You can use the same drill you use for drilling metal. Answer: Yes you can use a metal drill bit, but you have to be very careful with Plexiglas when drilling, it can chip-out, break-out, or even crack the Plexiglas.

The way to drill without no chip-out is to sandwich the Plexiglas between two pieces of wood. TIP: make sure the Plexiglas is held tight between the 2 pieces of wood when drilling.

The rear view mirror on a 1999 Cadillac Deville is replaced by loosening the retaining screw and sliding the mirror assembly of the mount. A new mirror is then slid into place and the screw tightened down.

if it is just the mirror order a replacement for that model. then break old glass with a small hammer,gently and peel glass parts off mirror back. it is held by double sided tape . push in new one after cleaning. if it is whole assembly remove door inside panel three nuts holding mirror in place and unplug if power from connector

Yes, it is not going to cause any problem

Depending on where the house is located and the sizes and types of windows you want... it can run you from $200.00 to over $800.00 per window...

You should go with a replacement window because of the difference in labor cost to install. A completely new window including the frame would be a tremendous difference. Make sure you get a insulated glass with a low 'E" rating and the glass should be filled with Argon Gas or Krypton Gas. They have a new composite made window that has an extremely high insulated rating.

If you are handy at all you can replace the old windows with new ones while saving a lot of money doing it. Changing out windows is not really all that hard and can reduce the cost of the windows down to $50-$300. and up according to the size and type of window you want to replace. I would think the average would run about$79.00 per 4'x4' double payne vinyl window purchased from your local home improvement store.

For more information visit the Related Link.

wel a 14 by 18 inch garage window pane would usually cost 6679 million dollars but from us at the warehouse limited dunedin new zealand you can purchase a 14 by 18 inch garage window pane for only 9999.99 dollars... isn't that cheap!!!!!

Mirros will break if something hard hits it. A basketball,tennisball,soccerball,tetherball,football ext... Also a peice of medal would probabaly break it or make it fall.

ten or more years of development depending on your version of Ubuntu. Ubuntu is a modern Linux distribution while windows 95 is an aging and unsupported parent of the current windows environment.

You can save a lot of money by doing the replacement yourself. Windows can be purchased at your local home improvement store reasonably cheap from 49.00- and up.

It depends on the size and quality of the window you're looking to replace. More information provided will help you on this question. Give us the size and type of window you're looking to replace. As for labor it's cheaper if you're having multiple windows done rather than just one. Places like Home Depot and Lowe's do installs but you might find it easier and cheaper to buy the window on your own and look up a local handyman that knows how to install it.

I would say an average is $200-$400 in most areas for a single window - though this can vary widely. If you don't have any tricky trim, shapes, access, obstructions,... you should have the window cost plus $200 labor - this includes re-installing existing trim, and some insulation and caulk. Again - this is a rule-of-thumb - there are MANY variables that can affect this - INCLUDING the time of year that you have it done. The dead of winter (with cooperative weather) is always good as business is slow.

The pulleys are used to transform any hand-draw wood rod and ring system to a cord-operated system. The pulleys should be adjusted properly by experts. Mostly, window covering companies offers free installation service of shades and blinds. Fifty shades and blinds is a window covering company who serve in ROWARD, DADE and PALM BEACH and provide free measurement and installation services.

It is a mirror or a looking glass

The reflective surface is a mirror. It can be highly polished metal or chromed, the surface of a calm area of water, or a flat glass plate with a silvered back and a protective coating.

Sure, as long as you have proper visibility to the sides and rear on both sides.

Yes, a mirror is nonluminous. It does not emit light by itself, it only reflects light emitted by other things.

Convex mirrors - they provide a good all-round view for security purposes.

Wherever the source of light is, after reflection by the surface of a convex mirror the rays would go always diverged. Hence the name "diverging mirror"

Convex mirrors are common in security applications. For example - if they're placed in a store at strategic positions, it's possible to view a large proportion of the store from one location.