Unanswered | Answered

Mazda 6

Parent Category: Mazda
Known for its sprinted, insightful and stylish design, the Mazda 6 is a mid-size car manufactured by Mazda Motor Corporation since 2002. The company’s Mazda 6 2011 model is equipped with a rearview camera, 17-inch alloy wheels and new cloth seat materials.
The Mazda6 was introduced for the 2003 model year to replace the Mazda 626. The Mazda6 was designed to be a more sophisticated and upscale car than the 626 because it would be the company's "flagship" or top model since the Millenia was also discontinued at the same time. But there wasn't a...
Plenty in Ardnamurchan Scotland.
Answer . well that depends on the type of driving, but i have gotten 800 km from a tank with the fuel light just coming on
go to either mazda6club.com or 6crew.com. they have a ton of information on doing it. use the seach and type in fog light mod.
The fuse box is located along the floor to the left on the driver side. You will see where you can slide off the panel to get to the fuses. The front lighter fuse is 10 and the rear lighter fuse is 15. See owners manuel 8-41.
6 gallons 3qt=
Answer remove air filter box, just a few clips i believe, move out of the way, then there is a metal clip.. just pay attention how it comes apart. then reverse order. New Answer I've just replaced the driver side low beam bulb myself, and it's not necessary to remove any box. BUT TAKE THE COVER...
Answer . If this only happens when vehicle is cold - most likely condensation accumulated in the exhaust system - normal condition. If this happens when vehicle is hot - may be an indication that head gasket is begining to leak slightly
Will,Bill,Hill,Ill etc. x gill, Bill, kill, fill, frill, chill, pill, mill, etc..
Press the button to unhinge your key and flip it open. Look where the key lies flat when closed, and there is a small tab. Push this tab in and the end assembly with the key assembly will slide out. The battery is in the half with the buttons, not with your key. Split the half without the key...
I have a 2003 Mazda 6 with approx 80k miles. This noise confounded me for months. On ours, it showed up when pulling into or out of our driveway (forward or reverse, always with the wheels turned hard left). It is NOT the CV joint in the axle. It is NOT anything rubbing in the fender well. It is...
I had the same problem. You will have to tap or beat the wheel or tire off from the inside with a rubber mallet or hammer after you remove the lug bolts. Do so evenly while rotating the wheel. It is designed and mounted to the hub on a tapered machined surface. JC
3000 miles or once a month. Whichever comes first.
Answer . I have an 01 Chevy 5.3 single cab short bed 4x4. The PCV valve is on the back of the left valve cover.
mines a 2007 and it gets there around 6.7 - 7.0 seconds
1, 4, 2, 5, 3, 6 firing order
Answer . Weak battery or poor connection - battery to starter. Possible bad starter.
bracket clips. . Answer . There are indicators on the pads that will squeak when they are getting worn out, but it could also be that the brakes need to be cleaned and the parts lubricated this will make them squeak when they are not worn out, brake dust will make the parts bind up and noisy. ...
Answer . I have been reading many websites. they all say that to replace the fog lights on this vehicle you have to remove the front bumper. This is true only to the extent of the passenger side of the vehicle. If you are attempting to replace the fog lamps on the driver's side, you can simply...
If you turn it on, the volume will change depending on your speed to compensate for engine noise.
take off your front numper and you will see. it is really easy
i have 04 Mazda 6 mt and find that only the 2003-2005 block are the same (at or mt same )or 14-15 mt engine same , wish there is interchenge page with some more info on engine swap
Horse Power The mechanical horsepower , also known as imperial horsepower , of exactly 550 foot-pounds per second is approximately equivalent to 745.7 watts. http://en.wikipedia.org/wiki/Horsepower
4 and a quarter to 4 and a half quarts
dont know what you mean by preformance, but your looking at a top speed of 170km, for the manual daewoos and they have a 50L fuel tank
16 city and 24 highway.........unless the car is modified in some way....
Answer . Complete "how to" posted here:. http://mazda6tech.com/index.php?option=com_content&task=view&id=36&Itemid=49. Includes videos :)
This procedure is for changing rear pads, not the rotors. . I'll assume you know how to remove the tire, or please stop now. You will need a 7mm hex wrench, 6" C-Clamp, hammer, long nose pliers and a screwdriver. Eye protection and work gloves are suggested for your safety as there is a lot of...
Well, its easy, take something hard and break the small triangle window. It costs around 100 euros - 200 euros with work and toning (dealer's price). If u have good insurance - it helps;)
pull off mud flaps and find the belt tensioner turn the nut on the tensioner pulley clockwise to loosen serpentine belt. Take belt off. Take the three bolts out of the water pump pulley and take it of then you have three bolts connecting the water pump to the motor take them off problem may be the...
pat itself is about $25. Very eazy to replace. Take off the passanger side wheel, the sensor is located on the back side of the engine right at the botton. You will need a 8mm socket wrench to take of off. You can get to it through the opening for the axle.
I also need to know I am also wondering the same thing, I have looked all over the internet and found nothing on this topic so far. Any help with this would be GREATLY appreciated. Looks like you need to remove the intake manifold. Doesn't look too difficult, but you should probably use new gaskets...
ono ca poepe peupo una fusible de 1 hjh donde wid is
The ROTARY engine is the best engine that Mazda made. It is still in use in the RX 8s
The calipers on a Mazda 6 turn inwards you don't push them to compress them.
Fuse . The stereo doesn't have its own fusebox, but the audio fuse is in the fusebox under the hood, its a 5amphere I believe. Whats your business with it?
On the V-6,Immediately in front of the oil pan. Probably the easiest oil filter to get at on any car I've ever owned.
I had a hard time with this one.. there is a wire latch across the back of the bulb that you need to un-hook before you can take the bulb out. If it is on your driver side you can disconect your coolent container to give you more room. Once you have the bulb out you need to take it out of the ...
i need stereo wiring schematic for 08 mazda 6 non-bose
HEADLIGHT BULB REMOVAL/INSTALLATION Low-beam . Disconnect the negative battery cable. . Disconnect the front combination light. . Remove in the order indicated in the table. CAUTION: A halogen bulb generates extremely high heat when it is used. If the surface of the bulb is soiled, excessive...
Bad brake pads (wear indicator rubbing rotor), brake pads not retracting and rubbing rotor, or bad wheel bearings. You need to have this looked at before possible great damage is done.
Answer . (1) Open the hood; (2)unscrew the retainer from the back of the headlight; (3)pull the bulb socket out of the headlight assembly; (4)pull out the housing clips and remove the housing from the grill. NOTE:on later models there only 2 clips that are pulled up to release the headlight...
you trade it in for a z
The 2004 Mazda 6 takes a 22" drivers side, 18" passenger side and a fairly specialized 12" rear wiper (wagon) that is difficult to find in the stores. See sources and related links below for more information. Since there are currently over 22 different wiper arm attachments, do not buy wipers just...
it's mounted on the end of the rubber intake rube that goes into the throttle body---it has a set screw on top and two black small vacuum tubes connected into it, as well as a wire
. Sorry but the differences extend beyond the type of interior upholstery..... 2.0 5dr TS2, 2.0D 5dr TS2 and 2.2D 5dr TS2 additional features over TS . Increase to 17" alloy wheels Auto dimming rear-view mirror Electric folding mirrors Automatic rain sensing front wipers 6-CD changer Front fog...
It doesnt. its to just give you pleasure
Shift it around 4.5k RPM. Don't go under 3k when driving or else you start wasting gas.
press 6 them am 1 at a time if it does not work call me on 07828329160 as i have done quite a few of these in the past
5000km on regular oil 15k on syntetic
Manual. Type F or Mercon. Automatic. Motocraft Mecron ATF
\nErr will display if you enter 3 times error code.\nsorry for bad english.\ni want say you entered invalid password 3 times
For Low beam and high beam, it is H1 bulb.
2006 MAZDA MAZDA3 2.3L 4-cyl Engine 2006 MAZDA MAZDA3 2.0L 4-cyl Engine CAPACITIES Engine, with filter..........4.6 quarts [1] Cooling System, W/ Heater Initial Fill..........8.0 quarts AMSOIL Antifreeze and Engine Coolant Cooling System, W/O Heater Initial Fill..........7.3 quarts ...
The 2004 Mazda 6 4cylinder has 160HP
The 2004 Mazda 6 V6 has 220HP
Inside glove box, unfasten the cable used to hold the box. Now the box hangs only on it's hinges. Now you can locate the filter. Open and replace. you might have to bend filter to fit it back in. Just make sure it sits flat afterwords.
You have to remove the front bumper to change the head lamp , i did it one time on my Mazda 6 2003 . Regards Abdullah al brahim from K.S.A
I found out you have to take it to the dealership because the bumper (among other things) must be removed. They said that the passenger side is especially difficult to replace. Although the bulb costs under $10, it will cost around $200 for labor (if not still under warranty.) Well you can do it....
Look at it and you will figure it out.
15.9 US Gallons That's 60 Liters (good rounded number like it should be) for the smart folks.
Answer . I do not know how much it would cost to have a factory sunroof installed by a dealer, but I expect it would be a lot more than a a respectable body shop would charge to install an aftermarket one
Ultimately, you could replace the whole unit with an aftermarket unit but it wouldn't be cheap. As you're already aware, the stereo system is kind of built in with various other things in the dash. Anything is possible of course if you're willing to spend some money but by the time you install even...
take out top slide pin using Allen wrench push and pry top of calliper down , i mean way forward streching hose slightly and take caliper and slide it off the bottom slide pin .
the speaker size on 09' Mazda 6i with standard system is 6.5 front and rear. with tweeters on doors in front
The driver's side low beam headlight is slightly easier to replace than the passenger side. The owner's manual states the dealer must replace this bulb, but it can be done yourself if you are handy. The main problem is limited access due to the crowded engine compartment. A flashlight and small...
In a 2003 Mazda 6, open the glove box, squeeze the sides gently and remove ithe box. The cabin air filter is directly behind where the glove box lives. It is a simple matter to unlatch the door and pull the old filter out. Reverse your steps to install the new filter and glove box. It helps to empty...
For real world warranty reasons, best case scenario have the oil changed by the dealership or buy Mazda 5w20 from the dealership and keep the invoice. If the vehicle is out of warranty, any new 5w20 synthetic oil will prove beneficial. Best results can be found by making concurrent oil changes and...
Call the nearest Mazda dealership first!! My sons had to be replaced and we took it to an independent auto shop...he had to call the dealership!! He told us he looked at it and thought the only way to get to it was taking off the front bumper so he called the dealership because he thought "this...
For an 08 year model, here is your answer!. CAPACITIES Engine, with filter..........4.6 quarts[1] Cooling System, Initial Fill..........7.4 quarts AMSOIL Antifreeze and Engine Coolant Automatic Transmission, FNR5 Initial Fill..........Not Specified Automatic Transmission, Total Fill 5...
Replace with a new cup holder assembly. It's $173. Ouch.
Tire size for a 1995 Mazda 626 4-cyl P195/65R14 V-6 P205/55R15
Depending on what year you have.R-12 up to 93 or 94,after that R-134a. The two different types are not combinable without system damage in the future. The easiest way to determine which refrigerant you have is by what type of fitting/adapter is on the vehicle. R-12 has male threads on the connector...
Good question! I took mine to the dealership since it is under warranty still. If not, it would be expensive and difficult to replace on your own.
Trouble code P0128 means:Coolant thermostat (coolant temp below thermostat regulating temp)
Answer . There is no way to change the trip computer to display MPG, except perhaps in the service centre, since the dashboard LCD which displays mileage is universal for metric and imperial countries (has both km and mile segments for displaying gas mileage).
P0442- Evaporator system small leak. P0440- Evaporator system malfunction.
Because its a Mazda! its normally part of the 75k service which costs anywhere between £500 and £850 depending on which Mazda garage you go to. Plus another potential £150 as apparently the auto tensioner can 'go' when replacing the belt. Mazda want £300 to change just the belt. But...
Operating from 2 Japanese and 14 international manufacturing plants, Mazda makes vehicles in many different countries.
\nRemove the door panel, find and repair the lock linkgage.
I was informed by my local dealership that after power is loss (disconnecting from the battery), using the switch at the window in question - take window down to lowest level and then bring it back up to it's highest level and hold the switch until you hear a 'click'. This process returned the...
1) Pop hood.. 2) Remove the rear cover of the headlight assembly by twisting counter clockwise 1/2 turn.. NOTE: you may need to loosen and move other things out of the way such as the air cleaner box before you are able to get to the back side of the headlight assembly.. 3) There is a spring clip...
Answer . \nthe altenater is located on the bottom, closest to the fire wall
You can not drain all the gas out, there will bee spillage.
Pulse is Green/red trace behind the stereo. Remove trim from around Handbrake, then lift the trim around the handbrake, access then to two screws at base of radio facia. Remove glove box (pull sharply to disengage). A third screw, which goes into side of radio can then be removed. Whole facia,...
4 mm Allen screw under 14 mm cap Next to the bracket that holds the parking brake cable to the caliper, there is a bolt with a 14 mm head that needs to be removed. This is a cap that covers the adjusting screw and should have a small copper washer. Insert a 4 mm Allen wrench into the hole you just...
VIN = Vehicle ID Number
Sure you CAN. The question is should you? Only you can answer that.
The Mazda 6 has the most common hook-end wiper arms. See sources and related links below for installation videos. Also, purchase the replacement blades first and there will be additional instructions/illustrations on the replacement packages. Locate and press the tab or button where the wiper blade...
1.) Remove the screw that is behind the inside door handle. It hasa small plastic cover that you need to pry off with a smallscrewdriver. 2.) Remove the screw that is directly under the pull-handle (thepart you pull to close it) of the door. There is a small piece ofsticky rubber that you need to...
A little diagram might make it easier to explain. FIREWALL -------- |1 2 3| -------- |4 5 6| -------- . FRONT OF CAR . Cylinder 4 is the leftmost cylinder closest to you if you are looking at the engine head-on. Cylinder 5 is the middle cylinder closest to you... Hope this helps!