0
Chrysler Concorde
Chrysler Concorde was a four-door, front wheel drive vehicle manufactured from 1993-2004 by Chrysler. The vehicle was designed with short overhangs and low slung windshield. Its wheels were effectively placed to the side of the vehicle to create a bigger passenger cabin than its competitors.
815 Questions
Where is the body code plate on a 1999 Concorde?
Usually on top of the right hand shock tower mount (under the hood).
How do you replace the air filter on a 1998 Chrysler Concorde?
what air filter do I change to help air condition flow. You car referring to a cabin air filter which this vehicle does not have.
Where is the thermostat located on a 1997 Chrysler Concorde?
It is under the housing where the upper radiator hose hooks to the engine.
Will 22's fit on Chrysler Concorde?
yes they will, as long as you have a low pro tire i have a 2002 with 245/30/22 tires
How muck is 2002 Chrysler concord car worth?
what is Chrysler concord 2002 car worth with 140000km in good condition
Where is the transmission filter located on a 1997 Chrysler Concorde?
It is inside the transmission pan.
Where is the thermostat in a 2002 Chrysler Concorde?
It is under the housing where the lower radiator hose hooks to the engine.
Why does your 1999 Concorde stall without warning and wont start back up again?
If it justs dies without warning while your driving and then takes a few seconds or a minute before you can start it again, it it likely the cam position sensor or the crank position sensor. I replaced both and it hasn't stalled since. In my case the car did not give any codes and my scan tool did not find any specific sensor faults. Both sensors are relatively inexpensive and easy to replace.
CAn anyone list the trouble codes for a 1994 Chrysler Concorde?
11 IGN reference signal. 12 Battery input to PCM disconnected during last 50 key starts. 13MAP sensor pneumatic circuit. 14 MAP sensor electrical circuit. 15 Vehicle speed/distance sensor. 16 Open or shorted condition detected in knock sensor circuit. 17 Engine running too cool.21 Oxygen sensor circuit. 22 Coolant temperature sensor circuit. 23 Intake air temp. sensor voltage high. 24 Throttle position sensor.25 IAC motor driven circuit. 27 Fault in injector driver interface circuit. 31 Purge solenoid circuit. 32 Fault in EGR diagnostics. 34Speed control solenoid circuits. 33 A/C cutout relay circuit. 35 Fan control relay circuit.41 Charging system excess or no field current.42 ASD relay circuit. 43 Fault in ignition coil control circuit. 44 Battery Temp Voltage.45 Overdrive Solenoid open or shorted 46Battery voltage too high. 47 Battery voltage too low. 51 Oxygen feedback system stuck at lean position. 52 Oxygen feedback system stuck at rich position. 53 Internal logic module problems.54 No cam position signal. 55 Completion of fault code display. 62 Indicates unsuccessful attempt to update EMR mileage. 63 Unsuccessful attempt to write to an EEPROM location by the controller. 64Methanol sensor voltage too low.
To call up codes, cycle ignition switch on, off, on, off and on within 5 seconds. Stored codes will be indicated by flashes of the power loss/check engine lamp. The codes will be indicated as two digit numbers, with a four second pause between codes. An example of a code is as follows:
- Power Loss/Check Engine Lamp illuminated for approximately 2 to 3 seconds as a bulb check, then turns off.
- Lamp flashes 2 times, pauses, then flashes 6 times.
- Lamp pauses for approximately 4 seconds.
- Lamp flashes 3 times, pauses, then flashes 1 time.
This would indicate that code 26 and 31 are stored. The lamp will continue to flash until all stored codes have been displayed.
Once the lamp starts flashing the stored fault codes, it cannot be stopped. If a code is missed, the entire procedure must be repeated. The lamp will not indicate if oxygen feedback system is switching lean-rich or if idle motor system is operational. The lamp also cannot be used to perform actuation test mode, sensor test mode or engine running test mode.
After all fault codes have been displayed, then power loss/check engine lamp can be used to verify switch function. The lamp will turn on and off as the switch is turned on and off.
Why is the traction control off light on on a 1999 Chrysler Concorde?
The abs computer has detected a malfunction and set a code.
How do you remove rear seat in 1999 Chrysler Concorde?
Remove the bench by prying up the bottom front edge on the outboard ends. Two vlips hold it in place. Then pull forward. Remove the back by first removing the two inboard seatbelt bolts. Pry the seatbelt holder away from the bolts. Pull forward on the bottom of the seatback and then lift up. There are three brackets holding the back to the interior chassis.
What is the coolant capacity of a 1994 Chrysler Concorde radiator?
According to the Owners Manual of a 1994 Concorde.
3.3 Ltr. engine 10 quarts
3.5 Ltr. engine 12 quarts
How do you change rear speakers in 2000 Chrysler Concord?
Step 1- open trunk
step 2- crawl in trunk
step 3- remove the upper insulation below the rear window, it has 2 clips up by the seat, and approx. 4 pegs holding it in place. After removing this set it outside of the vehilce
Step 3a.- cause i forgot to mention this step until i got to step 7, disconnect the rear brake light.
step 4- remove the insulation that is on the back of the back seat it is also held in with pegs
step 5- look up under where the speakers are and you will se approx. 3 more pegs that should be popped out, and 2 gold clips that should be pushed up. Pull the pegs, and puch the gold clips up.
Step 6.- Loosten bolts holding back seat in place and remove the rear portion of hte bback seat.
step 7- go inside the vehicle and carefully remove the remaining pieces that are covering the speakers, it will come out wouth some careful manuevering. Be carefull not to damage the side wall plastic by the door panels, or the rear brake light.
Step 8- unscrew the speakers
step 9- take a break and drink some water
step 10 put it back together again.
www.autoaccessorygarage.com
Where is the distributor cap located on a Chrysler Concorde lxi?
hope you have not looked too much for it! there isn't one. on my 2001 there is a coil on each individual spark plug to take the place of the distributor.
Can't connect jumper cable to Chrysler Concorde remote battery plastic covers it.?
Remove the plastic cover.
Does the radiator have to be replaced when replacing the engine?
If it is clean, undamaged, and in good working condition.....NO. Since the radiator needs to be removed, to remove the engine, now is a good time to have it cleaned and checked.
Whirling noise under hood for 10 seconds after engine is turned off?
It is probably your cooling fans. These are electric and may run with the engine turned off. It is probably your cooling fans. These are electric and may run with the engine turned off.
The cooling fan is supposed to keep running as long as the coolant is over temperature. If it runs too long, it could be the temperature sensor or a stuck relay. If the relay has become magnetized or fused, you need to replace it.
Why does your 1995 Chrysler concord keep overheating after you changes the thermostat?
Make sure the thermostat is installed correctly, then there are other factors to consider. Your radiator may be plugged or corroded ( if you run anything but the correct mix of coolant and water you will have this), The radiator fans may not be engaging, the water pump may be bad, you could have a head gasket failure.
How do you install water pump on 1993 Chrysler new yorker 3.5L?
This takes a certain level of skill to do...while you are at it, replace your timing belt and other belts, as well as your tensioner pulley and tensioner as it has probably become frozen. in other words, you have to disassemble the front portion of the engine, including the removal of both radiators so you can gain access to remove the harmonic balancer, etc. You will need to be sure you have the instructions for setting the timing marks on the cam and crank shafts. Good luck, I have been successful twice, as I also own a 92 intrepid 3.5L.
