0
Ford Trucks and SUVs
Trucks and SUVs are among the extensive product lines manufactured by the American automaker Ford Motor Company. Some of the models that belong to these product lines are the Ford Escape, the F-650, the Ford Transit and the Ford Cargo.
2,071 Questions
"Generic Electronics Module"
It is used on 1995 and later models according to my Haynes manual.
What exhaust system sounds better magnaflow or flowmaster?
I like flowmaster 3" with super 44 mufflers.
How do you tell what size of engine is in a 1976 ford F100?
if its a in line 6 its a 300ci------ if its a v-8 3to 4 options 302small block 351w still a smill block 351 Cleavland big block 400m or 460ci......
http://www.fordf150.net/howto/decodevin2.php
Use the VIN Decoder to find your motor if you know it is either the original or was replaced with the same size. The 4th character is your Engine Type.
As to the previous answer, correct me if I am wrong but from 1973 to 1976 the "H" code was for their 390cid.
How do I replace the float in fuel tank on a 1989 ford pickup?
you have to remove the fuel lines going to the top of the tank. then drop the tank. then turn the retaining ring on top and remove it. then you can pull the float/pump assembly and repair or replace. it's built together.
Where are the hidden vin numbers for 1994 F-150 Ford trucks?
I've been told there is a "hidden" VIN stamped somewhere on the frame behind the right front fender well, but I've never been able to find one. Good Luck!!
How to Read VIN Ford Explorer?
(Redirected from Vehicle identification number)
Jump to: navigation, search
"VIN" redirects here. For other uses, see Vin.
A Vehicle Identification Number, commonly abbreviated to VIN, is a unique serial number used by the automotive industry to identify individual motor vehicles. Prior to 1980, there was not an accepted standard for these numbers, so different manufacturers used different formats. Modern day VINs consist of 17 characters which do not include the letters I, O or Q. There are vehicle history services in several countries that can help potential car owners use VINs to find lemons and branded vehicles. See the used car article for a list of countries where this service is available. * en.wikipedia.org/wiki/Vehicle_identification_number *
Where is the o2 sensour bank 2 on a Ford F-150 2003 v6?
Bank 2 is the drivers side of the engine ( V6 and V8 ) in your Ford F-150
Sensor 1 is in the exhaust before the catalytic converter ( upstream )
Sensor 2 is in the exhaust after the catalytic converter ( downstream )
Where do you put brake fluid in a 2003 Ford F-150?
You put the brake fluid inside the brake master cylinder
Why would the abs light not go off in a 2001 Ford Truck?
A problem has been detected with the Anti-lock Brake System
It could be a fuse , a sensor , or some other problem
As long as the red " BRAKE " light is not on in your dash you
still have " normal " brakes
* my ABS light came on suddenly and the first ABS fuse that I checked was
not installed all the way , when I touched the fuse with my finger I heard a
click sound and the ABS light went out - just lucky I guess
Will a 1994 Ford F-150 5 liter engine fit in a 1990 Ford F-150?
Yes. The only difference is the TBfI and MPFI. (Throttle body fuel injection and Multi port fuel injection and corresponding computer controller.
What fuse number is for the cigarette lighter on a 2003 Ford Explorer Sport?
In the fuse panel on the driver's end of the dash (visible with driver's door open) in location # 17 is a 20 amp fuse for the cigar lighter/ OBD II.
What later model frame can you mount a 1954 f100 body on?
what later frame can you use for a 1954 ford f100
What part is a Three Hole Cap Screw Nut for automatic hubs - AKA Drag Shoe Nut?
It's a special nut found more commonly on early model Fords, Jeeps, IHs & very few GM trucks as it is only found on "external" hubs. The nut system contains 4 parts:
- Keyed washer
- Wheel bearing nut
- Keyed, index (with holes or slots) washer
- Drag Shoe Nut
There's two types of Drag Shoe Nuts
- Smaller diameter - Auto-Matic hubs
- Larger diameter - Lock-O-Matic hubs
Each uses the same keyed washer (#1) & wheel bearing nut (#2)
The Auto-Matic hub's DSN has four 1/8" diameter holes in its face, two of which are threaded, each of which contain a full dog point set screw that receives either a 1/16" hex bit or allen wrench. This uses an index washer that has holes in it. To lock the nut in place, one hole must completely receive a set screw.
The Lock-O-Matic hub's DSN has five 1/8" diameter holes in its face, three of which are threaded, each of which contain a full dog point set screw that receives either a 1/16" hex bit or allen wrench. This uses an index washer with slots in it. To lock the nut in place, at least two slots must completely receive a set screw.
The unthreaded two holes in either nut, receive a pinned spanner wrench/tool. The tool is used to tighten/loosen the nut. These nuts had a short life due to people being ignorant to their design & beating on the nut with a chisel and hammer, while the set screws were still seated. Sometimes the set screws' holes have been found to be marred so badly, that a 1/16" allen wrench can't be used to even feel around to see if there's still a set screw in the hole!
When uninstalling, you unthread the set screws completely and thread them back in three or four threads so you don't accidentally use the threaded holes with the tool... which is hard to do considering the threaded holes are the only two that are a perfect 180° apart. Then you spin the nut off... if you don't have the $175 tool, or the $10 tool that came with the hubs/service kit, you can make one out of a set of channel locks or a Cressent Wrench. Drill 1/8" holes in the head of the pliers or wrench and insert a 1/8" needle, roller bearing in each hole. Open pliers/wrench to the correct size and there you have it.
Upon Installation, the keyed washer is installed, then the wheel bearing nut (torqued to specs - usually 40 foot pounds) and then the index washer, flat side out. The set screws are threaded into the beveled face of the DSN until the dog points are almost flush with the interior face (flat) of the nut. Then the DSN is threaded on and torqued to specs.
What engines where available in a 1969 Ford F100?
the 240 cubic inch and 300 cubic inch straight 6 cylinder engines the 302 cubic inch V8 and I believe the 360 cubic inch V8
Where can i find a 1991 ford f350 headlight switch wiring diagram?
Go to your local auto parts store and get you a Chilton manual for Ford Pickups and Bronco 1987-96. They have a diagram for that.
How do you know when a fuel injector pressure regulator is going bad?
You will need to test the pressure of the fuel system with the regulator on and then disabled. You will need a manual for the correct pressures.
Be sure to read the fuel warnings in the manual as the fuel rails will be under pressure even with the vehicle turned off.
What is the towing capacity of a 1988 Ford F-150?
The Gross Combined Weight Rating or GCWR determines the maximum weight of a loaded tow vehicle and its attached loaded trailer. In a 1988 Ford F150, it tops out at 7800 lbs.
