0
GMC Suburban
Also known as GMC Yukon XL, the GMC Suburban is a full-size sport utility vehicle manufactured by General Motors Company from 1935 to the present. It has been one of General Motors’ most profitable vehicles.
904 Questions
Where is the Timing advance wire location 89 suburban?
It's a brown wire with a connector. It's located on the firewall on the driver's side to the left of the power steering booster. Pull the connector apart before checking the timing. Be sure to re-connect afterwards.
How do you change an interior reading light in a 2002 impala?
Carefully pry off the Reading Light Lens, pull the bulb straight out, push the new bulb (#194) straight in until it stops, carefully reinstall the lens matching the tabs with the slots...
You have turn signals running lights but no brake lights in a 1999 gmc suburban?
More than likely, you need to replace the stoplight switch. It is not a diificult change. Look under the dash directly where the brake pedal comes in contact with the dash when it is not depressed. Press the brake and notice the little contact nipple that pops out. That is the stoplight switch. Replace that, and you are good to go!!!
How do you replace a tail light in a GMC Suburban?
*** Open the rear doors and secure them so you don't get hit by them while you do this *** Look in the sheet metal directly behind the tail light assembly you wish to fix. There should be two rubber plugs; if so, remove them to gain access to the bolts that hold the tail light assembly. I would recommend a magnetic tool, as these bolts can slip and fall into the crevices back there! Rotate the assembly away from the body. If you try to pry the unit off, you will break the mounting tabs located in the forward portion of the tail light assembly. This means you have to grasp the inside part of the assembly that is closest to the middle of the 'burban and rotate them forward towards the front of the vehicle. For example, the rear passenger side tail light assembly would be rotated out in a counterclockwise motion towards the fromt of the vehicle. Unscrew the light bulb holder assembly and remove the bad bulb. Replace it with an exact replacement, and use the dielectric grease! It keeps out the water and prevents the corrosion of the bulb contacts. Hope this helps!
Where is the fuel tank pressure sensor on a 1998 GMC Suburban?
That would be attached on top of the fuel pump/sending unit assembly.
Are the threads on the bolt that hold the tensioner pulley left or right handed on a 1995 Suburban?
The bolt on the tensioner pulley are opposite of a standard thread. That is, righty loosey lefty tighty. I know this first hand because I stripped the threads on my pulley trying to remove it on my 94 Sub.
How do you remove the transmission pan on a 1995 Mercury Tracer Trio?
This is a messy, but easy job. First use some ramps, and get access to the underside of the car. Then remove the plastic skid guard on the drivers side of the car. It should have about 5 or 6 bolts. Once that is removed, you should see the fairly rectangular transmission pan. I'm assuming you already have a new filter and gasket, you shouldn't reuse the old ones. Also make sure they are the right size, and type. Line the gasket up underneath the pan to make sure. Then loosen the bolts on the lowest part of the tranny pan, (likely the side farthest from the front of the car), put something underneath to catch the dripping fluid. And slowly make your way around the pan bolts loosening them. Eventually the fluid will start to drain out. It WILL be messy. Once you've emptied what you can, carefully remove the other bolts and lower the pan. Removing the filter isn't hard either, just a couple of bolts. Make sure you don't get any crap inside the naked valve body, or you will likely wreck it. Clean out the tranny pan really well, and let it air dry. Make sure you clean your magnets as well. If you see any metal slivers, be concerned. If it's just a muddy sludge, you're probably ok. When replacing the pan, try not to over tighten, and tighten them in a criss-cross pattern to prevent leaks. If you have a rubber gasket, don't use sealant on it!
Why would a car stall when parking in a parking spot?
The most common reason for a car to stall is a lack of fuel. The gas tank could be empty or the fuel injectors. Need to be cleaned.
the engine might be siezed, put a big wrench on the crankshaft pulley and see if you can turn it starter could be bad (has a dead spot), to check have someone turn the key to start the engine while you tap continuously on the starter with a good size socket wrench, if it turns over by doing this, your starter is going bad and needs to be replaced. If it "clicks" or "clanks" it could be your starter solenoid. That is the unit riding piggy-back on the starter that basically starts your starter.
Is there an access panel to reach the fuel pump in a 1990 GMC suburban?
You need to drop the fuel tank down far enough to see where the fuel lines enter the tank. That is your access pt.
How do you remove the drivers side door panel of a 1996 GMC Suburban?
The question you ask is too involved for a proper answer. You may want to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.
How do you change heater valve in a 1999 gmc suburban?
with pliers, squeeze the spring clamps and slide them about an inch from where they are seated (all 4) remove one hose at a time and install it on the new valve in the correct position then put the clamps back into place. (don`t forget to refill the cooling system)
On a 1999 gmc 1500 suburban 5.7l where is the ac condensor?
on a 1999 gmc 1500 suburban 5.7 l where is the ac condensor
yes
Where is the TPS sensor located on a 1995 GMC Suburban?
Right on top of engine, next to fuel injector or carb, on passenger side. Usually has a wiring harness coming off the top if it.
What would cause a 1999 Suburban to continuously loose antifreeze and overheat?
If you cannot see an obvious leak, then the most common cause is a blown head gasket. Symptoms of a blown head gasket in addition to the 2 you listed are, sweet smell at the exhaust, air bubbles in the radiator with the cap off engine cold, creamy foam on the underside of the oil fill cap, overfull oil level, missing or loss of power. This condition is very serious and engine damage will occur if you continue to drive this vehicle. Have it repaired ASAP, and stop driving it.
How do you replace a throttle position sensor of a 2003 Chevrolet suburban?
It is located on throttle body, opposite side of where throttle cable is located- Unplug it, remove any screws or bolts holding it on then install new part in reverse order.
Armrest in 1992 suburban in locked position?
If the armrest on a 1992 Suburban is in the locked position and will not unlock, check for a foreign object that might be stuck in the hinge. Sometimes the armrest can lock if the bolt holding it on is too tight.
How do you adjust timing on a 1994 suburban?
Warm it up,....un-plug the pip conn.under the glove box(tan/black),adjust the dist.to read zero degrees before top-ded cntr,..
How do i remove fuel tank on 1997 suburban?
There are two straps on the fuel tank if you follow them up you will see two bolts that hold the strap to the frame if the fuel tank is not empty put a jack under it to hold it up so it wont fall.
How do you fix your stuck tailgate on your 99 gmc suburban?
To fix a stuck tailgate on a 1999 GMC Suburban, first, check the latch mechanism for any debris or rust; clean and lubricate it if necessary. Inspect the wiring and connections for the tailgate release switch to ensure they are intact. If the latch is still stuck, you may need to manually release it by accessing the latch mechanism from inside the tailgate. If these steps don't work, consider consulting a professional or replacing the latch assembly.
