0
GMC Yukon
The GMC Yukon is a full-size sport utility vehicle manufactured by General Motors from 1992 to the present. The car is available as either a two-door or a four-door model. It features a front engine and a rear/four-wheel drive.
1,653 Questions
How long is the warranty against rust on the 2015 GMC Yukon-XL?
The 2015 GMC Yukon-XL has a 6 yr./ 100000 mi. warranty against rust.
Where is the fuel filter on a 2002 gmc Yukon?
On the left side (driver side) in the frame about driver door.
Where is the jack on a 2007 Yukon Denali XL?
Should be in the compartment by the left rear wheel inside the vehicle.
How wide is the 2009 GMC Yukon-XL?
The 2009 GMC Yukon-XL is 6 ft. 7.1 in. (79.1 in.)1 one-touch power windows wide.
What kind of transmission does the 2012 GMC Yukon-XL have?
The 2012 GMC Yukon-XL has a 6-speed shiftable automatic.
You know how to adjust the headlamps but how do you know they are in adjustment?
park facing closed garage door about the length of your vehicle away.you should be on level ground to do this.headlight beam should be same width apart same hidth to, as your vehicle.only go 10 to 15 feet away.i found it best to do on low beam.high will fall into play without adjustment.works for me.hope this helps.oh and do it when its just starting to get dark.good luck let us know if it works for you.
1999 gmc Yukon just all of the sudden lost power and hard to keep running?
I have a 1996 GMC Yukon and this happened to me. I would be driving on the highway and all of a sudden the engine would shut off. The fuel filter and then the fuel pump turned out to be my problem.
How do you change a serpentine belt on 1996 gmc Yukon?
Just changed the water pump and hoses to the water pump. I decided to replace the serpentine belt as well. This should take about 15 minutes. No need to remove the fan shroud if you can reach down below to the pulleys. The fan blades can do a number on your hands if you are not careful. I wore mechanics gloves as a precaution. Make sure you draw a diagram of how the belt goes on before you take the old belt off. On the front of the tensioner spring pulley there is a square slot for a 1/4" ratchet drive to fit into. Insert the ratchet into the slot and turn the ratchet so the tensioner pulley swings down. With the tension released, slip the belt off the pulley Make sure the new belt is the correct one. I was sold an incorrect belt and spent way too long reinstalling trying to figure out why the new belt would continue to squeal intermittently Hint: if you have the old belt in one piece, compare the length and width to the old one. I read some forums that said to replace the tensioner as well if the new belt is squealing. In most instances I don't think this isnecceassary. I think more times than not the new belt is not the correct one and is more than likely too long. Thread the belt over and under the pulleys according to your diagram. Pull down the spring tensioner as above with the 1/4" ratchet to slip the new belt over the tensioner pulley. Make the belt is seated well over and or under the pulleys Double check to see all tools are out of the way. Start the engine to test for any squeals or chirps which could indicate belt slippage.
How do you reset the ABS light on a 2000 S 10 with a 2200?
The ABS light is on because you have a problem with the ABS system. The problem would have to be repaired before the light will go out. After it is repaired the light will clear itself. You can start with attaching a scanning device into the vehicles diagnostic link and reading the trouble codes. This service can be done at many auto parts stores for free if you purchase the parts needed for repair from them.
Where do you locate the ignition module on a 1998 GMC Yukon with HO 350?
the module is in the distributor the module is in the distributor. you will have to remove the cap and rotor. it should be held on by 2 screws. good luck
How many gallons of gas can a 2000 Yukon hold thanks?
My 2000 Yukon XL holds about 32 Gallons. The regular Yukon may hold a little less, I am not real sure.
The vacuum tube to the heater control is broken in two or cracked...usually in the engine compartment. It's a black, hard plastic tube or pipe about 3/16" od. Without vacuum, the heater control cannot open and close dampers to direct air flow.
When would it be time to change the timing belt on a 2001 GMC Yukon XL?
TRUCK HAS A CHAIN THAT SHOULD LAST THE LIFE OF THE TRUCK. I don't believe that these engines are equipped with a "timing belt" like some Japanese & European cars, but a conventional timing chain as used by American manufacturers for many years. Timing chains do not need to be periodically replaced as with timing belts, except at engine overhaul which should at 150,000-200,000 miles or greater on today's engines if serviced & maintained properly. GM V-8s have timing chains as far as I know; expect to change around 50 to 70k miles is traditonal wisdom.
How wide is the 2010 GMC Yukon?
The 2010 GMC Yukon is 6 ft. 7 in. (79 in.)1 one-touch power windows wide.
How do you replace the front parking light bulbs on a 1994 Ford Probe GT?
The way I did it on my 94 probe gt was to jack the car up about 8 in off the ground, USE some kind of jack stand, and for the left one, just remove the plasic splash guard on the left side to grand somewhat easy access. For the right side, I ended up taking the right front tire off, then partially removing the front bumper on the right side, then I removed the wind shield washer resivor, and while pulling out slightly on the bumper, SQUEEZe your hand in there and with a little skill change the bulb.
1. Remove the screws and pull down on the front portion of the fender liner. This provides just enough room for your hand to reach in and access the two bulb holders.
2. Turn the bulb holder counterclockwise and pull it out of the housing.
3. Pull the bulb from the holder and replace.
** What the book DOESN"T tell you is that it's a whole lot easier if you turn the tires opposite from the side you need to get too. Also, if you have really large4 hands or forearms, you may need to take the tire off altogether.
What is this code p0507 i got from a 99 GMC Yukon?
Trouble code P0507 means:Idle control system,RPM higher than expected
How do you install a screw drive garage door opener?
For safety's sake, the best way to learn how to install ANYTHING is to carefully read, understand, AND FOLLOW the MANUFACTURER'S INSTALLATION AND OPERATOR'S MANUAL. Good luck ! j3h
Just to add on...
I rarely recommend for people to install their own garage door opener. It's not that an average person couldn't do it himself/herself, but most people won't follow directions carefully enough to have the opener installed properly. It also isn't too cost efficient to spend an entire day trying to make an opener work.
However if you are insistent on doing this yourself, please read all the directions before hand (not just while you install the unit). Prepare yourself and you will be able to do it. Also, there are instructional videos online. Just search it up and watch through them. If you have any doubts, just call a local company to come out and help.
How do you adjust emergency brake on 2001 GMC Yukon?
The emergency brake is designed poorly and uses a circle asembly with two brake pads on the circle there is some adjustment ,but mostly designed to be replace when changing out the disk pads . It is like a drum brake withend the rear disk brake.
