0
Honda Accord LX
The Accord LX was launched in 1978 as a 3-door coupe and was later re-designed as a 4-door hatchback and 4-door sedan. The latest model is available as a 4-door sedan powered by a 2.4 liter engine.
4,658 Questions
Where is the oil dipstick on a 97 Honda accord?
Open the hood and look around. It is right there in front of you on the engine. If you cannot find the dipstick then you need to shut the hood and seek professional help. You have no business under the hood of your Honda.
Wilke339's answer:
If your Accord is 4 cylinder, the oil dipstick probably has a yellow pull ring handle, and is located toward the driver's side of the engine, up high near the top belt pulley.
How do you remove a frozen cv axle nut on a 1994 Honda accord?
Spray on some PB BLASTER and let it sit for a day to penetrate. That's what I woudl do first, then check back if it's still tight. You may need to use heat.
How to get a frozen axle nut off.Use heat and an impact gun. If you don't have access to either take it to a repair facility.Yea, Just use an impact Hammer... keep pounding, it's taken me up to 8 or 10 seconds on one nut, out of about 30 or 40 that I've done.
How do you reset oil light on 2007 Honda Accord?
If you are referring to the maintenance required light, then press the odometer reset button and hold it while turning on the ignition switch to the on position. After around 5 seconds the light will reset.
If you are referring to the red oil pressure light there is no reset. It is on because there is low or no oil pressure. Stop driving the car immediately or you will destroy the engine. If the oil level is full, Seek professional help.Does the opening look like your ignition key would fit into it? If so, it is likely to allow you to shift the car out of park without inserting the key into the ignition. You would simply insert your key into the slot, and the shifter should unlock. Try it.
What is causing your 2001 Honda Accord to lock in park?
There is a brake sensor assembly that has gone bad. Down by the top of the brake pedal is where it is located. if it is bad it will not let you shift out of park and your brake lights will not light up when you depress the brake pedal as well. The part can be purchased at a Honda dealer for $60 plus dollars or you can buy on at NAPA for $38.50 It was really easy to install all you need is a small wrench to losen a nut and then thread the new one on. Taking the electrial wiring clip lose was the hardest part because it is in such a small space under the steering wheel by the brakes.
Where the DRL relay is located in a 2001 Cavalier?
its located right in the fuse box on the driverside dasboard. its the only black box type fuse in the panel Just know that when you remove this, you will have only one headlight working and an annoying DRL light on your gauge cluster. Unless you know the jump sequence...
Why would a 1988 Honda Accord Lxi leak oil?
My 1989 Honda Accord Lxi with 168K miles was leaking engine oil at the rate of about a Quart every week. Now i just check oil levels weekly and haven't needed to replenish it other than as normal. The fix i found was in replacing the PCV valve. Interestingly, the advice i had gotten for a non expert like me was to not try and save a few bucks by just cleaning the old PCV valve. But to replace it with a new one. The reasoning was that in a properly working PCV valve, not only is it there to help redirect vapors back into the combustion chamber, but to aid in preventing vapors from building up which could also be a cause for premature oil leaks around the crankcase area.
How do you change the front rotors on a 1993 Honda accord?
Some say, "Take it to a repair shop. They have to be pressed on." This is completely incorrect. There are two alternative methods for accessing the front rotors (or the outer hub - as in the case of broken wheel stud replacement).
The design in question is the "hub over rotor" or "trapped rotor" used on the front wheels of these older Hondas. The outer bearing/hub has to be pulled apart from the inner bearing in order to remove the rotor.
First, remove the axle nut. Use a breaker bar and a 36mm socket. Leave the car on the ground to loosen the nut initially, then jack the car to remove the nut.
Two ways to do to the hub or the hub+rotor:
1)USING A SLIDE HAMMER
Four bolts connect the outer hub to the rotor. To remove only the outer hub (that is, leaving the rotor on) - as in the case of replacing broken wheel studs...
-remove the four bolts that connect the hub to the rotor
-attach a slide hammer (loaners available at most auto part stores) to two of the wheel studs (lug bolts)
-give the hammer a few good strokes (I've gotten it off in one stroke)
-to replace the hub, use the hammer to seat it back in place
Of course, if you need to remove the rotor in addition to the hub, disconnect and move the brake caliper assembly out of the way. Support the loose caliper assembly with a wire hanger so as not to damage the brake hose. Once the hub is off, the rotor is free to remove.
2)USING TWO LONG 10MM X 1.25 BOLTS
There are 4 bolts that hold the hub to the rotor; remove two of these (the ones closest to the 12 o'clock and 6 o'clock positions) and re-insert two 10mm x 1.25 three inch long or longer well-greased bolts; when these two new bolts (they should be available at Ace Hardware) contact the backing plate (which will be supported against these bolts by the inner hub), alternate tightening them until the outer hub (attached to the rotor) separates and can be pulled away from the car. Remove all 4 bolts (the two new long ones and the remaining two original ones) and the rotor will separate from the hub.
How do you remove a governor from a 97 Honda Accord?
It has no governor. The speed is computer controlled.
How do you fix a seat belt on a Holden vl?
If the seatbelt wont retract your coil inside is stuffed so go to the local reckers yard an buy a replacement.
there is 3 bolts you have to remove the plastic cover carefully with a flat head screew driver then undo the bolts and remove the belt then replace with the new one. IMPORTANT NEVER EVER OPEN THE SEAT BELT COIL DEPARTMENT
(THE BIG THING) AS THE COIL WILL SPRING OUT AND SLICE YOU UP!!!!!!!!
The 1st one i did i was just playing trial and error i lost half a finger and have a nasty scar about 4 inches long on my face that needed 32 stiches and nearly lost an eye.
2003 Honda accord flasher relay?
The flasher relay is located above the fuse box/fuse panel on the left side of the driver's foot-well. To access it, you will need to lower the black plastic panel above the brake and accelerator pedals. You no not need to remove any screws, the panel is held-on by 3 clips at the front (side closest to driver's seat). The relay itself can be found on the top-right corner. It is typically a black box. To be sure, turn on your 4-way flasher (assuming that this works) and follow the clicking sound. From my understanding, the flasher relay is a dual-relay, acting as the relay for both the 4-way hazards and the turn-signals.
How do you reset viper alarm on your 1992 Honda Accord?
my ignition on my Honda accord will not turn over all of a sudden.could this have something to do with the viper alarm? thanks
What does it mean when your Honda Accord is ticking while idling?
Valve adjustment needed is a possibility.
Where is the obd2 port on a 1996 accord?
It is under the ash tray in the center console. Just remove the tray and you will see it..............
if its cold out your gear oil is just very thick which makes it hard to shift once the car gets going it should be fine
What type of oil to use for a 1995 Honda Accord lx 4 cylinder?
SAE 5w30 any major brand of your choice.
What is wrong when the brake light are dim 92 Honda accord lx?
Answer Probably a bad ground or the bulb needs changing. battery is dead or a bad ground wire connection
