0
Honda Prelude
The Honda Prelude is a two-door sports coupe produced from 1978 to 2001 by the Japanese automaker Honda. This car during its production run served as a testbed for a number of features that would eventually be commonplace for the rest of the Honda line: examples include double-wishbone suspension, four-wheel steering, fuel injection, VTEC (after the Acura NSX), and ATTS.
1,006 Questions
Where is the fuel pump relay located in a 1988 Honda prelude?
where is the fuel pump cutoff relay located in a honda 88 prelude?
What is 0-60 for 91 Si Honda Prelude 2.0?
i have an 87 prelude si and mine will do 0-60 in about 4.5-5 seconds with a cold air intake.
Where do you add transmission fluid on 1987 Honda prelude 5 speed?
There is a fill plug just aft the right drive axle. Looking at it from the right front wheel area, it is about the 10 'o clock position on the transmission. 17mm male plug. The drain plug is about the 5 'o clock position and is a 3/8" drive female plug.
Where can you find a diagram of the throttle body for a 1998 Honda Prelude?
The throttle body diagram for the 1988 Honda Prelude is found in the maintenance manual of this car. It can be obtained as a print out from an automotive store as well.
How do you adjust the flooded carburetor on a 1984 Honda Prelude?
How to you syncronize a 1984 honda prelude carburator?
Where is the fuel pump relay for a 1992 Honda Prelude?
It's in the steering column. You can access it from under the steering column. It's light gray in color and on the left side.
Where is the air sensor located on a 96 Honda Prelude si?
On/by the Throttle body, should read "sensor assy map"
Would a 1996 F22 VTEC motor fit into a 1998 Honda Prelude?
Yes. The 4th and 5th generation ('92-'96 and '97-'01 respectively) JDM (Japanese Domestic Market) Honda Preludes had trim levels which used the F22B motor.
Where is the ECM main relay on an 86 Honda prelude?
The main relay is located on the drivers side cab of the car, it is specifically located behind the pull cable for the hood release. it is mounted to the wall and has one electrical connector plugged into it. to remove use your hand to unplug your sensor and then use a 10mm socket to remove the relay from the mounting position. Before assuming your relay is bad check all of its post connections and all of them should sit at 0 when testing at 20 ohms i beleive. mine is currently out and you will notice that the car will not even turn over.
It is called a main relay as it controls the entire cars electrical service and distribution. At some stores it will be listed under "fuel pump relay" but do not be fooled by the people that work in these stores as they have almost no mechanical experience and do not pay more than 85 bucks for this relay, you may be able to find a temporary replacement at a junkyard.
What colors did the 1998 Honda Prelude sh come in?
The 1998 Honda Prelude came in six colors. They were Nordic Mist Metallic, Eucalyptus Green Pearl, Flamenco Black Pearl, White Diamond Pearl, Midnight Purple Pearl, and San Marino Red.
How do you replace the head gasket on a 1985 Honda prelude?
the head gasket in any vehicle is located within the engine compartment. Since it's a 4 cyl engine, there'll be 4 gaskets spaces, although the head gasket is a singular unit. You'll have to "drop the engine", which really means raising it. Then, dismantle, and replace. Pain in the a$$...I had that prob w/ a 91 Ford, and in that particular vehicle, it wasn't worth the effort. I also recommend going into your nearest Honda dealer, specifically to the parts dept., and request to see the SHOP MANUAL for your year of Honda Prelude. Most of the time, they'll let you go through it, and even photocopy any pages you might need, free of charge.-Callie * I did mine without removing the engine, but it's not very much fun. Just make sure you clearly label where all the vacuum hoses, etc. It makes re-assembly a lot easier. Remember, you have to remove all of the old gasket from the head and the block before re-installing everything or it won't seal right. The aluminum scratches very easily so try not to take too much off or put any deep scratches in them. Also, you *have* to use new head bolts and *have* to use a torque wrench. Look in the shop manual and it will show you the order to tighten them in and the torque specs. If you don't follow them you'll have problems down the road after the head gets hot and cold a few times. (And then you'll get to do it again. yay!)
Where is the fuel cutoff switch located on a 2001 Honda Prelude?
You're probably talking about an "inertia switch" - sorry, I'm not sure if anyone besides Ford uses them for sure. Your owner's manual should tell you.
Honda prelude Drivers side window goes up crooked?
The rubber is dry; use a silicone based lube roll windows all the way down and spray all the rubber that guides the window up and down
Wheres is the intake temperature sensor in a 1994 Honda Prelude non vtec?
The IAT is located on the driver side of the intake plenum on an SI model. If you're standing in front of the engine, it is directly to the right of the label "PGMFI." It's a white plastic sensor.
How do you disable python alarm in 93 Honda Prelude?
You disconnect the wires to the little black box labeled Python usually under the dash on the drivers side.
On a Honda prelude 1996 transmission have somthing to do with the check engine light to come on?
That is very possible but most likely yes
Where is the iat sensor located in a 93 Honda prelude?
The IAT sensor on the 1993 Honda Prelude is located to the right of the intake manifold as you face the engine compartment. It is connected with red and green wiring.
Where is the speedometer cable on an h22a?
It is electrical. Vehicle Speed Sensor (VSS) on top of gearbox sends signal to ECU which sends signal to gauge cluster.
What is the small yellow dipstick for in a 1991 Honda Prelude?
Trans fluid. On the 97-2001 thr is no trans dip. Only a bolt under the car you stick your finger in to check level. So if you have two dips one for oil the other is for trans. Ludekrs
Where do you Connect pcv hose to carb or intake?
Pvc is not made be used in an automotive application.
If you chose to go with an "off label" use your on your own!
pcv (positive crankcase ventilation) is usually connected to a central vacuum source at the base of the carb.
Can to much oil make the check engine light come on and idle rough?
To much oil in an engine can cause it to flood which will then lead to blowing seals. But it should not effect how the car idles.
