0
Hyundai Elantra
The Hyundai Elantra is a compact car manufactured by Hyundai in 1990 for the 1991 model year. It is known as Hyundai Avante in South Korea and was formerly marketed as the Lantra in Australia and some part of Europe.
1,636 Questions
Where is the trans axle fill on a 1990 Toyota Camry?
Look on the side of the transaxle for a plug, if this is a manual transmission. If it is an automatic, the fluid is added through the tube the dipstick is in. A manual transmission takes a heavy gear oil, usually about a 90 weight viscosity, and should only be filled until the oil begins to flow out of the hole. Check the level by inserting your finger into the hole. If it is right below the level of the hole, it does not need more oil. If this vehicle has several hundred thousand miles on it, it might be wise to drain the transaxle and fill it with new oil. If it is an automatic with more than 100,000 miles, flushing the transaxle is a good idea.
If you have a moon roof, sometimes the drain hoses can leak and the water can run down the door channel. just a possibility, hope it helps.
What grade of oil does a 1999 elantra use?
5W30 synthetic would be best.......see the following from another post.
3.75 qts
Correct Amount1999 HYUNDAI ELANTRA 2.0L 4-cyl Engine Code DOHCOil Filter it calls for is this one.
Wix # 51334
Gasket Diameters
O.D: 2.475
I.D: 2.173
Thk: 0.233
Length: 3.194
CAPACITIES
Engine, with filter..........4.2 quarts[1] 5W30
Cooling System, Initial Fill..........6.4 quarts
Automatic Transmission, Total Fill..........7.0 quarts
Manual Transmission, ..........4.6 pints
1. After refill check oil level.
TORQUES
Oil Drain Plug.....26-32 ft-lbs
Manual Transmission
Fill Plug.....22-25 ft-lbs
Drain Plug.....22-25 ft-lbs
How do you remove speakers from a 2002 Hyundai Elantra?
fold down back seat and remove three pushpins-remove the two sides of the back seat with 13mm socket,bolts are towards the bottom of the seat cushion. remove seat belt anchors in back dash with same socket.remove third brake light buy pushing towards backglass then pulling up and away. don't forget to unclip wiring. Three or four pins hold the back dashpad in place. go thru trunk and pop clips back thru hole then go to back seat and pull out the dash cover and speakers are exposed.
Paint color code for elantra GLS?
This is stamped on square metal badge,Open the hood and look on right side of bulkhead.
Can also be had by called a dealer with the VIN number
What oil to use for Hyundai i30 crdi?
Use recommended oil - Shell helix ultra diesel sae 5w40 or Shell helix ultra extra 5w30 if you have dpf installed. Otherwise you can use castrol edge turbo diesel 5w40, or Q8 excel diesel 5w40.
What kind of transmission does the 2014 Hyundai Elantra-Coupe have?
The 2014 Hyundai Elantra-Coupe has a 6-speed shiftable automatic.
Where is the input and output speed sensors for a 2001 Hyundai Elantra?
I think this should answer your question The vehicle speed sensor (VSS), which IS MOUNTED ON THE TRANSAXLE, is a "Hall Effect" switch.
I Had the same problem. Found answer here:
http://www.2carpros.com/topics/airbag.htm Basically, it is the voltage regulator causing a voltage spike and blowing the lights and causing an airbag issue. I haven't yet fixed the problem but seems to make sense with the symptoms I had (bright flicker before lights went out).
Transmission goes in reverse but will not engage in drive in a 98 Hyundai elantra?
It sounds like you need a new transmission. I had the same problem but I replaced the transmission and decided to trade it in.
The ignition coil on an 2001 Hyundai Elantra?
to replace the ignition coil on a 2001 elantra 2.0.....take the plastic cover out(5 bolts...10mm) once you see the coil pack to your right........................................
disconnect the plug wires....make sure to keep it in order....... there are 2 bolts attached to each side of the pack take them off......then disconnect carefully the 3 cables attached to the pack ...put the new pack....bolt it in...plug the the 3 wires ....then connect the ignition wires and you are done.....put the plastic cover back....................remember to disconnect battery before you start working on this.
How do you replace the water pump on a 1999 Hyundai Elantra?
CAUTION: Some models are equipped with anti-theft-radio make sure you have the activation code before disconnecting battery
- Disconnect negative battery cable
- Drain cooling system if coolant is relatively new save it
- Remove the accessory drivebelt
- Loosen the water pump pulley bolts.Remove the water pump pulley bolts and then remove the pulley
- Remove the alternator.Note the position of the alternator bracket on the water pump it must be installed in the same position when installing the water pump.Remove the alternator bracket bolts they're also water pump bolts and then remove the other four bolts from the water pump
- Loosen the hose clamp and then disconnect the water pump coolant inlet pipe connection hose.Detach the coolant inlet pipes from the block and then disconnect the coolant inlet pipe from the water pump mounting boss.Remove and discard the old o-ring
- Clean the bolt threads and the threaded holes in the engine to remove corrosion and sealant
- Compare the new pump to the old one to make sure they're identical
- Remove all traces of old gasket material from the engine with a gasket scraper
How do you change a 2002 Chevy Cavalier automatic transaxle fluid and filter?
Hey Eric==Pull the trans pan and filter then replace the filter and pan and about 4 quarts of fluid. GoodluckJoe
In the owners manual, it states that you do not need to change the automatic transaxle fluid. But you should check it. Unfortunally, you'll need to raise the car, and then drain it to see if you have the correct amount, and if it needs to be changed. There is no dipstick, and this is the only way to check the fluids levels.
the first answer is is the best but if you pull the pan its actually 6.9 quarts to refill
Fluid Capacity Specifications (4T40-E) Application
Specification
Metric
English
Bottom Pan Removal
6.5 liters
6.9 quarts
Complete Overhaul
9.0 liters
9.5 quarts
Dry
12.2 liters
12.9 quarts
Measurements are approximate
Hyundai Elantra 2006 replace headlight?
The passenger side bulb is much easier to replace than the driver's side, and I suggest you use it as a visual aid.
On the driver's side, you will need a Phillips screwdriver to loosen the three plastic screws that attach the shroud to the front of the car. These screws do not come out, they simply anchor the plastic clip through the metal. When the screws have come up about an inch, gently lift the shroud & set it out of the way to the left. You can also remove the 10mm bolt at the other end of it, but it is not necessary. Just be gentle as you shift things. On the passenger side, you can simply work around the windshield washer fill tube.
The headlight enclosure has an airtight cap on it, which you remove by turning slightly counter-clockwise from behind, facing the front of the car. Pull the electrical connector straight off the back of the bulb. The bulb itself is secured by a brass-coloured bent-wire do-hickey. To remove the bulb, you simply press the wire where there is a rectangular bend on one side near the bottom, next to the silver screw. The wire will unhook and you pull it up out of the way, freeing the bulb. (If you are working on the driver's side, go have a look on the passenger side to see how it works.) Pull the bulb out, being careful not to hit it on anything. Note that the metal ring around the bulb has the notched part at the top.
Now put the new bulb straight in, with the notch at the top. Hold the wire do-hickey up out of the way as you slide the bulb in, let it drop back into place while you keep the bulb in place (I placed a finger on the connectors to do this), then press the wire rectangle to hook it back on. Put the connector back onto the bulb and replace the black plastic cap on the assembly. Check to make sure the light works before reattaching the shroud. Replace the passenger side cap if you've been using it as an aid. I know, I know, but we've all forgotten something under there once or twice.
Gently move the shroud back into place, & put the plastic clips back into the holes - if the screws dropped back into the clip you will have to pull them out or the claws of the clips won't fit through. Tighten the screws and Voila! You are safely lit once again.
What would cause a rise and fall of RPM while idling in gear?
the rpms should rise and then drop no more then 500 rpms when the fan on the radiator turns on and then off.
Why does blowing on food make it cooler?
It cools because the moisture inside the food vaporize and carries away heat. That is why the steam from your food is hot.
How many types of sensor in car?
A LOT! over 100 that's for sure. It vary per vehicle make and model.
some commons that you will find on every vehicles are Oxygen sensor, crank sensor, MAF sensor, Camshaft sensor, coolant temperature sensor,...
How do you change the factory stereo in a 2000 Hyundai Elantra GXE?
Got this hint on another board and its answers all your questions!
Goto www.hmaservice.com (Hyundai webtech 2000) Set the Model Year and engine drop-downs on the top of the page and then click Search on the far right. Try entering the search kewords "dashboard", "interior" and/or "radio" (leave all items as the default values)
["dashboard" worked for my 2004 Elantra, and "radio" for my 2000 Elantra]
You should get a "Removal" or "Instruction" document that you can click on. This contains all the details of removing the dash assembly and radio.
Enjoy!
I went to the website and this is what you get although the pics didn't seem to work here. I ran into some snags where there was not nearly enough info and so I added a bit between steps three and four.
>ELANTRA(RD) > 2000 > Engine > Engine Control > Body Electrical System > Audio & Antenna > Antenna > REMOVAL AND INSTALLATION >
REMOVAL AND INSTALLATION
AUDIO
1.
Disconnect the battery negative terminal.
2.
Remove the shift lever boot and the rheostat assembly using a (-) driver.
3.
Remove the center facia panel's 2 mounting screws. (2EA)
At this point it is going to tell you to pull off the facia panel. You will want to
get down and unscrew the heater control cable down near the gas pedal.
There are two screws holding it in place. One is holding the cable casing
and the other is holding a white piece that swivels attached to the cable.
Once these are free the facia piece should come free. If you do not do this you'll only have about a half inch of play and will probably break a clip yanking on stuff. You can do the rest without removing
all of the wire assemblies attached to the facia panel it is a little in the way
but manageable.
4.
Disconnect the heater control cable and connectors (6EA), and then remove the center facia panel.
5.
Remove the audio mounting screws (4EA) and remove the audio.
6.
Installation is the reverse order of removal procedure.
ANTENNA
1.
Disconnect the battery negative terminal.
2.
Remove the LH luggage side trim.
3.
Remove the antenna mounting nut and insulator.
4.
Remove the antenna mounting nuts (2EA).
5.
After removal of the antenna cable and connector, remove the antenna assembly.
6.
Installation is the reverse order of removal procedure.
FRONT SPEAKER
1.
Remove the inside handle mounting screw, and then separate the inside handle assembly from the door latch mechanism by removing the handle's plastic hook.
2.
Unscrew the door trim mounting screws and detach fastener. Remove the door trim.
3.
Remove the speaker mounting screws (3EA), and then remove the speaker assembly.
4.
Installation is the reverse order of removal procedure.
REAR SPEAKER (FOR SEDAN)
1.
Remove the rear seat cushion.
2.
Remove the rear seat side back.
3.
Remove the rear seat belt lower mounting bolt.
4.
Remove the high mounted stop lamp.
5.
Remove the rear partition trim and the package tray trim.
6.
After removing the speaker mounting screws (4EA), remove the speaker assembly.
REAR SPEAKER (FOR WAGON)
1.
Remove the rear cargo security screen and the speaker grill
2.
After removing the speaker mounting screws (4EA), remove the speaker assembly.
Obd 2 code PO133 Hyundai Accent?
P0133 is a trouble code for o2 sensor, what it means is 02 sensor slow response bank1, sensor 1 (before cat) should be located before the flex pipe. What causes this code is that there are many reasons, one could be a faulty sensor, a bad exhaust leak or minor usually happens if the leak is before the sensor depending on which leak is greater. vacuum leak can cause this code due to not enough oxygen entering the exhaust manifold. check with the dealer or local garage, it is very hard to actually state which problem is causing this code.
Mine was coming on due to a massive exhaust leak, when fixed the code disappeared.
Why is coolant mixing with the oil in your 2001 Hyundai Elantra?
At best you have a blown head gasket that is letting coolant into the cylinders and from there past the pistons into the sump where it becomes emulsified with the oil and will destroy the rest of the motor if you run it.
Or it could be a warp or a crack in the head same symptoms but a lot more expensive to fix.
And then there is the possibility of a crack in the block that's really expensive.
No mater which one it is it has to fixed before you run it again because the coolant in the oil will destroy every bearing in the motor.
It can also commonly be a ruined Intake Manifold Gasket. This is a more common problem in GM vehicles, but can also occur in others as well. This is still not a cheap fix, but less expensive than new heads or head gaskets.
What does P with an exclamation point mean on control panel of 2001 Hyundai Elantra?
My best guess would be for the parking break. Easy way to test, when the car is running just pull the lever or step on the lever and see what light turns on
