0
Jeep Cherokee Laredo
The Jeep Cherokee Laredo was manufactured from 1985 to 1992 as a full-size SUV. Its earlier models had a 2.5-liter engine while the four-liter engine came out after 1987. It was designed primarily for the North American market.
1,043 Questions
Your jeep chugs and backfires when you apply gas?
It could be your timing is off or your timing chain needs replacement.
How do you change the armrest panels in the front doors of a 1996 Jeep Grand Cherokee Laredo?
I think this year had sone peeling problems and the dealer actually has a repair kit available for 1996 only. Otherwise, find a salvage yard and replace the entire panel. There are about three screws that need to be removed, then carefully pry the panel from the door "popping" each of the plastic retainers loose. There will be some electrical connectors for the window and door lock and light but these unclip easily.
What Causes sudden loss to 4 wheel drive on jeep grand Cherokee 1995?
there is a possibility that your shift linkage is messed up. if not that then it is a sensor.
Where and how do you install a MAP sensor on a 1997 Jeep Grand Cherokee Laredo?
The manifold absolute pressure sensor is installed in the intake manifold it is a simple installation thread in thread out.. but it is in various locations on the manifold depending on which engine you have The chilton or haynes manual will show you.
What causes a p0118 engine coolant temp circuit high input error and how do you fix it?
Most likely culprit is the ECT (engine coolant temperature) sensor. It can give this code and still not read high on the temp guage.
What is the engine code 66 for a 1997 jeep Cherokee?
Error code 66 on a 1997 Jeep Cherokee means TCM to PCM failure. This code means that the transmission control model is not communicating with the powertrain control model.
What does code p0513 means for jeep Cherokee Laredo 2005?
Basically it means it means you have a invalid skim key and you are going to have to replace the i mobilizer module with new keys and reprogram.
Hey Becky==There probably is part of the linkage that has come loose. GoodluckJoe
answerThis problem applies to 95-98 Blazers as well as the GMC and OLDSMOBILE versions. On the newer blazers they have a secret hole in the back of the tailgate where you can insert a rod to release it.The key to the solution is to get the window to unlatch first do that you can open the tailgate and then perform the repair inside the tailgate. This was not easy. I got very frustrated even after reading some of the other "answer" suggestions like the Allen key method. To unlatch the window you will have to climb inside behind the tailgate facing out. You need to make a tool using a bent piece of heavy wire 12" long (like a coat hanger - but preferably stiffer). Bend a 90 degree hook in the end about 1-1/4" long. Make another bend about 6" away from the first bend to make a "J" shape.
Hold the tool parallel to the glass and slide down - hook first - into the center of the plastic hump concealing the latch mechanism. Rotate the tool so that the hook faces the front of the vehicle (the 1-1/4" section should be horizontal at this point). Line the tool up about 1/2" to the passenger side of the hump's centerline. Push the whole tool straight down with about 2 pounds of pressure. This pushes on the release and the window will pop. After you get the window to pop you will see how the latch is made and it will seem easy. I made a drawing I can fax to those who need it. Fax your request to 718-857-8499 and I will fax back the sketch. In the future I will get drawing scanned, I will post a link.
After you get the tailgate down,You will need to remove the back interior panel of the tailgate, this has 3 screws, 1 in the top middle and 1 on each side, after they are out it is just held in by clips so remove slowly. With this removed you should be able to look through little access panels to see if something has come apart, some of the assemble you can reattach from this point for harder to reach areas you will need to remove the steel panel. This is easy it just has a lot of screws and a couple of clips you need to unclip. Just remember what screws and clips you unhooked so assemble will be easy as well.
Where is 4-wheel drive switch located on a 1995 Jeep Grand Cherokee Laredo?
The 4 wheel drive switch is located on top of the transfer case
Where can you get a copy of the master fuse box diagram for a 1991 Jeep Cherokee Laredo?
Chiltons Auto Manual for Jeep Cherokees has diagrams for each of the jeep fuse boxes
What is the difference between 242 transfer case and a 231 transfer case?
the 242 has full time four wheel drive made possible by a center differential while the 231 only has part time four wheel drive and no center diff.
The drive shaft attachment point yokes, and spline numbers could also be different. The 242 is usually in a Jeep, while the 231 is in a truck.
What is the location of the wiper Intermittent module on a 1993 Jeep Cherokee?
On a 1994 Grand Cherokee, it is located behind the driver-side kick panel. Maybe that will get you started.
How do you replace the wiring harness on a 1988 Jeep Cherokee Laredo?
It really depends on which wiring harness. If you are asking about the whole cars wiring I would seriously take it to a shop. Other harnesses may be easy, like the radio harness, and door switch harnesses are the easy ones.
How do you reset the oil change light on 2008 jeep grand Cherokee Laredo?
Turn the ignition on, engine off. Press the gas pedal to the floor three times in 10 seconds.
Interior lights flicker in 97 jeep?
check for blown fuse. Or check and see if fuse is in all the way.
goto http://www.wjjeeps.com/faultcodes.htm got retrieve codes write the instructions down and get the code from your jeep. now find out what code means what issue. thsi should help with your issue if not then disconnect the battery and wait 30 seconds then reconnect the battery. wait for the computer to reset ( about 2 minutes.) see if the same light is still on. if it is ON then get a pro to look at it because it is most likely over your head and needs a mechanic. if it is NOT ON then drive and wait for it to come on and when it does then get it serviced....
What is the correct factory tire size for a 1999 Jeep Cherokee?
The correct factory tire size for a 1999 Jeep Cherokee is 225/70R15.
Where are the circuit breakers on a 2000 Jeep Grand Cherokee Laredo?
The circuit breakers are in the junction box next to the battery. They are at the front of the box with clear square lids and amp ratings printed on them.
Where is fuel filter located on the 2005 jeep grand Cherokee Laredo?
The fuel filter on a 2005 Grand Cherokee is part of the fuel pump module in the fuel tank.
Is the pinion nut on a 1993 jeep grand Cherokee Laredo right threaded or left threaded?
Right hand. Righty tighty lefty loosey.
Where is a flasher fuse located on a 1997 Jeep Grand Cherokee Laredo?
The '99 flasher fuse is in the fuse box in the engine compartment and the flasher switch solinoid in under the dash on the left side. Hope this helps.
The flasher fuse is located on the kick plate of the passenger side above the fuse box. I actually just replaced one too!
How do you engage 4 wheel drive on 1988 jeep Cherokee?
the best way i have found to engage the 4x4 mode is to be rolling at about 5 to 10 mph because this takes the the tension off the transfer case and the shifting link that runs to the transfer case this makes for an easy transition from 2 wheel drive to 4 wheel drive this will make your shift link last longer and extend the life of your transfer case if u don't do this and shift to 4 wheel while sitting still u might notice that its a little more stiffer to do this stiffness will cause your shift link to get sloppy and cause problems later in life such as not being able to shift to 4 low or even to neural or even in real bad cases full time i wouldn't recommend shifting at fast speeds cause the transfer case gears spin at very high rpm or revolutions per minute if something happens to bind up because of lack of maintenance this could result in some serious damage to the cases to take it out just push the lever to 2 wheel and be shore to back up in reverse about 20 feet or so u should here a soft click noise that's how u know its disengaged i hope this helps and in joy your Cherokee and safe wheeling
Easy! Pull off your fuel line on the fuel rail, Put a few bucks under the car, And then turn the ignition on, DON'T TRY TO START IT! But this will drain the old gas out, Next, Reconnect the line, Refill the tank, And add some sort of Water Remover to the tank. Then it should be good!
