0
Jeep Cherokee Laredo
The Jeep Cherokee Laredo was manufactured from 1985 to 1992 as a full-size SUV. Its earlier models had a 2.5-liter engine while the four-liter engine came out after 1987. It was designed primarily for the North American market.
1,043 Questions
What does P0155 code in a 2004 jeep grand Cherokee Laredo mean?
Trouble code P0155 means:O2 sensor heater circuit malfunction
(Bank 2 Sensor 1)
In my case it was the ignition switch. They overheat and carbonize the connectors so that eventually the switch "burns" out and can even lock up and never works again, as it did in my case I don't have an answer for this problem, but I am experiencing this very same problem to the letter. I will add some troubleshooting steps which have not helped, so that noone makes the same mistakeS: * Replaced four relays under the hood ($41) * Replaced starter relay ($54) * Replaced turn signal module ($2) * Replace emergency flasher module ($6) Other troubleshooting discoveries: * Power coming from the engine side the wiring seems to be alright * For every item listed in the original question above, the fuse box was dead (no power) when probed with a test light and the ignition was on. The ACC fuse contact was also dead. * All of the other fuse sockets of the unaffected systems were hot (had power going to them) NOTE: A portion of the fuse box seems to not have power, due to either a bad hot lead, or a bad ground. Which ever is the case, it appears that section of the fuse box is on a totally different electrical circuit from the working side of the fuse box. My next step is to find a good wiring diagram, pull the fuse box, and start tracing bad connections, burnt wires, and anything else I can find. If this helps anyone to track down the problem...PLEASE...Share! Thanks. :o) Have your battery tested - it is most likely a battery-related problem even though it has enough charge to start. I had the same problem; replaced the battery and all is well. Have you checked the fusable links?? - Look where your posative cable goes to. The first stop is a junction block that has many smaller wires coming from it. Each of these wires are for your sub-system voltage feeds. They protect the circuits at the point where they connect to the junction block, it act the same as a fuse, but it is designed to handle much higher currents than a fuse. You can buy the appropriate load fusable link to replace the one that has gone bad, just splice it back into the harness and all will be well again.
How can you tell if your freeze plugs have popped out on a 94 jeep Cherokee?
Your engine will overheat, rapidly if they have 'popped out' (on any vehicle, incidentally) because all the anti-freeze will leak out.
What makes a 1992 Jeep Cherokee Laredo make noises in the transmission?
It could either be loose bolts on your bell housing or anything down there. or it could be your torque converter and it could need to be replaced. i actually have to take the torque converter out of my 1992 jeep Cherokee Laredo because my block cracked so I'm selling it for parts. and it is a pain in the neck but much worth saving the money. to get the instructions on that i googled how to replace a torque converter and i found this one:http://neptune.spacebears.com/cars/stories/torqconv.HTML
it isn't for a jeep Cherokee but other sites i looked at say it is pretty much the same in every rig. maybe just different sized bolts and stuff.
What would cause an occasional drip on the passenger floor of a 1995 Chevy 4WD?
My 95 blazer has a leak that normally shows up after a heavy rain. It is caused by water running down the windshield into the air duct outside the vehicle. The water runs down the passenger side of the duct where the fresh air vent is located. If the fresh air vent is stuck open and a heavy rain comes, I'm given a puddle of water in the passenger side floor mat.
How many quarts of oil in a 1990 strait six Cherokee?
Normally 6 quarts in the 4.0L. Put in 5, run the engine, shut it off and check the level to be sure.
How do you replace the fuel injectors on a 1988 Jeep Cherokee Laredo 4 liter 6 cylider engine?
the fuel rail is held on by four bolts and i believe they are 9/16 on mine. the rail should just come up with a little force and the fuel injectors come out of the rail. at least that how my 88 is.
1985 300zx non turbo turns over but no spark tried new button and coil still no spark?
first check for juice. it sounds like your not getting power to the coil. check with a test light. if your not getting power work back to the source proboly a fuse of some sort in the engine compartment
How many hours it takes to change a fuel pump on a 92 jeep Cherokee?
About 30 minutes. The fuel pump on the Cherokee is on the front side of the tank, instead of on the top like most cars, thus allowing you to remove it without lowering the gas tank! There is a locking ring that holds it all in and can be removed by using a flathead screwdriver and a hammer to carefully tap the ring counter clockwise till it comes off. Then just pull out the pump, and replace. Be careful not to bend the float installing the new one or your gauge won't read right.
Where is the radiator cap on a 1988 Jeep Cherokee?
doesen't have one. Have to do everything from the over flow.
Gunite can last for decades with good soil conditions. Plaster is the part that needs to be redone periodically, but maintaining proper chemistry will allow your plaster to last much longer.
THIS WAS MY QUESTION, BECAUSE THE 3RD BRAKE LIGHT WAS BLINKING I THOUGHT THERE WAS A MAJOR PR0BLEM,TURNS OUT IT WAS THAT BOTH BULBS WERE BAD,CHANGED THEM AND EVERYTHING WAS FINE
How do you change the speedometer sensor on a 1993 Toyota Corolla?
The speed sensor itself is located on top of the transmission housing, and it is accessable (though a bit of a reach). Go twords the back of the engine compartment (it's best to look through from the passenger side) If you look straight down from the back end of the fuel injector assembly you'll see a black connector hooked to some wires, right on top of the transmission housing. It's held in place by a single bolt. That is the speed sensor.
To remove it, first unplug the couple (the thing with the wires in it). It snaps in so you'l have to give it a squeeze to get it loose. Then with a 10mm wrench (or close to that) loosen the bolt. Once the bolt is out, grasp the sensor and pull it straight up. It will be oily and will have a gear on the bottom. That gear is spun by another gear inside the transmission. That's how it works.
I would strongly recommend doing some continuity tests with a multimeter. The sensor costs over two hundred freaking dollars.
How do you shift into 4 wheel drive on a 1992 Jeep Cherokee Laredo?
OK, So far I have found this information in my vehicle owners manual. There are illustrations which help explain what to do exactly. I am unsure if your transmission is manual or automatic. I recommend locating an owners manual for your vehicle to verify the correct way to engage 4 wheel drive for your specific vehicle or find a local mechanic to assist you in learning the proper technique. I would not want to mis-inform you.
Do you need a scanner to retrieve fault codes on 1993 Jeep Grand Cherokee Laredo?
You can check the trouble shooting codes by turning the key to the on position, then back one click to the accessory position, (do not turn it off), repeat this three times and wait for the Check engine light to begin blinking. The light will blink as in a Morse code, count the blinks. i.e. blink, blink pause blink, will be a 21 code. You can find the coresponding problem to the codes in a Haynes or Chilton manual. 21 is the beginning and 55 is the end. Scott
Can you swap a 4.0 with a 4.0 high output in a jeep Cherokee?
All Cherokees 1987 & up have the H.O. 4.0(those that came with 6cyl).Some models just don't have the emblem.
Where is the crankshaft sensor located on a 1996 jeep 4.0 liter engine?
Driver's side, about 11 o'clock in relation to the rear of the motor. You should see a three wire plug with an associated harness traveling down into this area.
Part will cost just over $40.00.
well hate to tell u but it sounds like ur starter is out bro or check ur wires
Where does the oil go in a Jeep Wrangler when it leaves the oil pan?
It circulates throughout the engine area. Unless it leaves the oil pan from the oil plug then it should go into some kinda container so you can dispose of it. Most parts store can do that for you.
Turn your ignition key backwards to put your auxiliary power on. Make sure all your windows are up, and then get out and hit the LOCK DOOR button a few times to lock all your doors. Now shut your driver-side door and go to your passenger door. Use your key to open the door, BUT when you turn to unlock it, turn it a few times. Now get in and try to start it. Let me know if that works 807-597-6178 Brian
