0
Jeep Cherokee
The Jeep Cherokee is a full-size SUV vehicle that came in two versions: the SJ model (1974 to 1983) and the XJ model (1984 to 2001). The chassis was based on the Jeep Wagoneer but had a 6.6-liter engine.
2,083 Questions
Where can I get a fuse map for a 1997 Jeep Cherokee interior fuse box?
check the users manual.or you can go to the nearest parts store and sneak a peak into a repair manual ie haines chilton etc..
Can you adjust the rocker arms on a 1997 jeep Cherokee Inline 6-cylinder?
No, they are torqued to a specific amount and the lifter controls lash.
No, they are torqued to a specific amount and the lifter controls lash.
What was the last year Jeep Cherokee was made with the 4.0L 6-cylinder engine?
The last Cherokee was 2000.
The last Grand Cherokee with a 4.0L was 2004.
The last Wrangler with a 4.0L was 2006.
Is the Jeep Cherokee front wheel drive?
The original Cherokee, 2001 and older, was rear wheel drive or four wheel drive. The latest Cherokee, 2014 and up, is front wheel drive or all wheel drive.
Where do i find a steering column diagram for a 1993 jeep Cherokee?
When investigating possible problems in a car it is important to have a diagram in which to compare looks. A steering wheel column diagram for this car can be found in the cars maintenance manual.
How do you open the rear door on a 1997 Jeep Cherokee?
it is quite easy you see, on the outside of what one calls a door, there is this strange looking object that sometimes sticks out or sometimes is flush with the door, sometimes the same or sometimes a different color than the car,this is called the "door handel" you grab that and by either pushing a button, pulling up or out it pulls on a metal rod inside the door which in reaction releases the door latch which holds the doorshut when the door is closed. it is just so east that my 3 year old son can even opperate a door handel wiuth perfect ease.
Why would 1993 jeep Cherokee limited start then die what would cause that?
I purchased a '93 1 week ago with this result. The engine would start and run for appx. 2 seconds and die. When I would hook up the battery, the alarm system would go off. The problem was a door sensor for the security system. The system was disconnected by a mechanic. He worked on it appx. behind the left side of the glove box (after removing a lot of dashboard).
How do you program your keyless remote for a 1999 Jeep Cherokee?
TRY THIS Sit inside the vehicle with all the doors closed. Place ignition in the OFF position. Open the driver's door. Leave Open. Move the mechanical door lever to the LOCK position. Turn the ignition to the RUN position. Aim the transmitter at the Keyless Entry receiver and press Lock button. Hold for five seconds until the door locks cycle. Turn ignition OFF within 20 seconds.
How can you change thermostat for your 93 Jeep Cherokee?
follow the upper rad hose to the block and it will be right there i think its 2 13mm bolts and that's it be sure to clean the housing and block of old gasket or else it will leak
How do i fix a broken blend door in a Cherokee?
The most common cause of your symptoms is blend-door failure. This is a design flaw created by Chrysler engineers. Basically what happens is that every 20 times the vehicle is started, the A/C system software tells the blend doors to recalibrate to ensure that the airflow is as accurate as possible. The problem is that the stop point is made of cheap plastic. The stop point connected to the actuator breaks. Shortly thereafter, the blend doors break because they cannot withstand the pressure of the actuator pushing them beyont their limits after the stop point has been broken. Passenger side is typically affected first, followed by the driver side. If the doors fall with gravity into the down position, you will maintian A/C. If you hit a bump on the road and they fall into a mixed position, you will have neutral temperature. Either way, no heat is a symptom because that is the up position for Jeep Grand Cherokees (99-2004).
I have tried this product, the Blen-Dor repair kit which will replace the plastic drive connector piece and the plastic blend doors with solid aircraft quality aluminum parts. Aluminum was chosen because it will be close to the weight of the original parts. The blend door shaft is a ½" solid piece of aluminum rod machined to fit. The two doors are aluminum sheet stock tig welded onto the door axle shaft with a foam covering applied to both sides of the door panels, all to make a one piece assembly. The second piece is the drive connector it is a ½" solid piece of aluminum rod with steel pins. The drive connector is machined to fit the actuator motor and to fit onto the end of blend door axle shaft assembly.
About how much does replacing fuel filter on jeep cherokee cost?
While I do not know the direct answer, a very useful website to learn that is ... http://www.repairpal.com/estimator.
1996 Jeep Cherokee owner manual?
You can find them on Amazon for around $33.00 or you can download one for around $10.00. You might find them cheaper if you look around a bit.
What model of transfer case came in a 1994 Jeep Cherokee?
It will be either a NP 231 or NP 242. The 242 being the "Full Time" and the 231 being the "Part Time" 4x4 transfer case. There is a tag on the side of the case that is a small circle with the type and gear ratio on it.
How much slack should a serpentine belt for a 1996 jeep Cherokee have?
You need to measure the slack before determining if it is too tight or loose. To do this place a straight edge on the power steering pump pulley and the one to left of it, press down on the belt with a couple of fingers and use a measuring tape to measure the deflection from the straight edge. If the belt is too loose you will be able to press it quite a bit. If it is just right you will be able to measure about a 1/2 to 1/4 inch deflection. Too loose the belt will usually slip and squeal loudly
What kind of oil goes in a 96 jeep cheerokee?
10w30 Has been going into my '98 for over 100,000 miles without any problems.
How do you change the crankshaft positioning sensor on a 1996 Grand Cherokee with a 4.0L?
it is on the driver side of the bellhousing-near the top-it is hard to get to if you are under the trans you can look up and see it .you may have to drop the rear of the trans a little bit by unbolting the crossmember..good luck
Where is the switch that activates the back-up lights on a 1996 Grand Cherokee?
It is a three wire switch on the driver side of the transmission.
Possible reasons why four wheel drive not working on 1988 Jeep Cherokee?
If it is like my 1990 Cherokee the 4WD is vacuum operated. If the vacuum lines are old and brittle and possibly broken then the 4WD wont work. Also, sometimes it can become temperature sensitive (like mine) and wont engage initially in cold weather. There may be other causes, but that's what happened to mine AND my brother, who has a Comanche eliminator.
How do you replace the crankshaft sensor on a 98 jeep Cherokee?
disconnect the neg battery terminal.the crank sensor is on the drivers side in the back of the engine where the engine and the transmission meet.there will be a little cover with two 10mm bolts holding it in.it is a very very tight spot you can see or get the bottom bolt from underneath if you can get the vehicle up.Please use extreme safety precautions if using a jack.once you get those two bolts out remove the sensor the connecter for the wire should be near number 6 fuel injector
How do you refit the serpentine belt on 1997 Jeep Cherokee 4.0?
I just changed a serpentine belt on my '97 Cherokee 4.0 you need to loosen the 2 top mount bolts (I think they're 13mm) on the power steering pump and loosen the 15mm bolt in the middle of the idler pulley. Then loosen the tensioning bolt on the lower side of the power steering pump Lower (left hand side facing pump from the front) follow the diagram to route the new belt( should be on a decal under the hood) replace belt then tighten using the tensioning bolt on lower side of the power steering pump to get 1/4" to 1/2" of deflection between puleys (when you press down on the belt) then tighten the bolts on top of the power steering pump And don't forget to tighten the idler puley bolt in the center of the puley. Run engine for 3 to 5 minutes to seat the belt. then recheck the belt tension. Caution! be sure to route new belt propperly or you could run the water pump backwards NOT GOOD
Can i make my 1999 jeep grand Cherokee limited also 2 wheel drive?
Sure, just don't shift it into 4 wheel drive...
Where is the buss on a 2000 Jeep Cherokee?
The bus is the communication network between computers on the vehicle. It consists of two twisted wires that run to each computer and the data link connector under the dash.
