0
Jeep Comanche
Produced between 1986 and 1992, the Jeep Comanche was a pickup truck version of the Cherokee compact SUV. Available as a rear-wheel and four-wheel drive model, the vehicle’s body, suspension and styling was based on the Jeep Cherokee.
271 Questions
Why does my Jeep Comanche idle high?
If you have a multi port fuel injected 6 cyl, it's probably the idle air control. I have
replaced mine a couple of times over the years. 2 screws and it plugs into the
throttle body next to the throttle position sensor. Costs around $60.
Will a Jeep Comanche fit a 350?
a Chevy 350 small block will fit into a 86 jeep comanche with some modifications.
-A 350 small block will fit in a 86 comanche without modification just be prepared for a lot of work beacuse when you do that the ENTIRE driveline needs replaced all the way back to the knuckles on the u joints at the differentials. you will also need to adjust the motor mounts. but nothing significant.
How do you change heater core on 87 jeep Comanche?
First of all you haave a super old car second i recomend you get to a auto repair before you get into any serious action
i have the same problem i think its the stupid choke that is hooked to the airbox and cnnected to the exhuast header
How do you reset the check engine light on a 1992 jeep Comanche?
Resetting the CEL will only result in it coming back on unless the problem is fixed. Once you have fixed the problem, disconnect the battery for 30 minutes then reconnect and wallaa.
Borden Comanche
Where on earth can you find a height sensing proportioning valve for a 1989 Jeep Comanche?
lol, i have a 91 Comanche and just ran across the same problem. after contacting a dealership, i had learned that they had stopped making those in 95. when i asked the dealer, what should i do with my jeep, he told me good luck, im just going to run a brakeline above ea wheel and just get 2 brake hoses, the rubber ones, and run them both down with the rubber hoses. you need to get a rubber hose with 2 female ends that except a 3/16 steel line, at least a foot long, $20ea.
Where is the oil sensor lacated in Jeep Comanche 86?
on a 2.5L AMC four it's located above the passenger side engine mount.
How do you change the speedometer setting on a 1988 jeep Comanche 4x4?
Good question. BUT in most states it is illegal to change the odometer on a motor vehicle.
Why Comanche headlights work but tail lights don't?
Check fuse for parking/tailights Could be a bad headlight switch
Hello Make sure that everything is clean where the shifter meets the transmission. You may have worn bushings in the arms, or changing the gear oil and putting some Lucas trans additive (for standard trans) may help. A mechanical repair may be the only way to fix it.
sounds like a fuel filter, do you have any more dignostics?
Why did jeep stop making the Comanche?
Because CHRYSLER bought AMC and they aren't the smartest people on the planet!
Because CHRYSLER bought AMC and they aren't the smartest people on the planet!
And another reason that they stoped is because Chrysler needed to cut cost and they already had trucks in the lineup so they didn't need the Comanche pickup.
What type of oil in an 86 jeep Comanche 2.8l engine?
The recommended type of oil in a 1986 Jeep Comanche 2.8 liter engine is 10 W 30. This oil can be purchased at any auto parts store.
Where is the fuel pump located on a 1989 jeep Comanche?
It is located under the driver side between the tank and the engine. I need a vacuum hose diagram for the same truck . If you have one, please post it. Thanks
Yes, many of them. These were very commonly sold as new in Florida.
The low pressure side of most cars is the larger of the 2 lines. This should hold true for the Comanche as well.
Can a 1995 Jeep Wrangler engine be placed in a 1987 Jeep Comanche?
probably
Edit: Will it work? Yes - especially if it's the 4.0. Is it legal? NO. In California, the law prohibits installing an older motor than the year of the project car. I.E. you can install a 1993 motor in a 1984 vehicle BUT you CAN'T install a 1995 motor in a 1987 vehicle. It may be legal in other states so check with your local DMV to make sure BEFORE you drop the cash on that swap.
Sounds like no gas is getting to the carb. eaither the choke is done or and most likely the fuel pump is done. The fact it will start with a shot of sure shot and then dies out usually means there was no additional fuel to burn hence, the fuel pump is not pumping. You can also check to see if the choke is pumping by havingsomeone continously pump the gas then watch the primer see if there is any gas. I had an old For Ranger do the same thing. John Ottawa, Canada
Where is the neutral safety switch located for the 1992 Jeep Cherokee?
Neutral safety switch is on the passenger side of the transmission oddly enough. It is delicate and can be easily broken as it is made of bakelite material and will not take much stress. DO NOT PRY on this device when making adjustments. They cost in the range of $180 to replace. Keep in mind that this same switch is what turns on the backup lights as well as allowing the Jeep to start in Park. So if you have trouble with backup lights AND/OR the thing won't start in Park (but will in Neutral) this is the likely culprit. Here is a link to some pictures so you know what you are looking at. http://newton.tek-ed.com/jeep/thumb0001.htm And here are some generic instructions from a fellow Jeeper (thanks to Ed Kummel for the following post): "The device is on the passenger side of the transmission opposite of the shift linkage. If the underside of your Jeep is like mine, then the shaft that this device is on is gunked and corroded and difficult to remove. If you're lucky, then you won't really have to remove the device. To adjust the switch, you will need several people (at least two) Loosen the bolt at the top. The hole is slotted which will allow for ~a little~ ammount of play. Have one person in the car with their foot on the brake and the shifter in reverse (with the key on of course). Have the second person behind the car looking for the reverse light. You are under the car moving the switch through the slotted play. When the person in the back sees the reverse light, top moving the switch and tighten it down...and hopefully you're done! If this doesn't fix your problem, then you will need further work. Removing this thing is a real problem. The metal is a cheap pot metal and the plastic is bakelite. So, it will shatter with a minimal amount of force. Plus the wiring harness is wire-tied to the main harness leading up to the engine compartment! So, don't force it!"
