Jeep Liberty

Check the wiring harness for the motor to the sunroof. The harness may be loose and might need adjustment. My sunroof on my 2002 Liberty Limited stopped working and I dropped the headliner and found that there was loose wire. I clicked it back inot place, and it works just fine.

A.C. circulates air(just like a fan) and turns it cool.

Four

Unfortuately if you don't have a least 2 keys for you can, your going to have to go to dealership for a new one, its gonna cost $300..

19'' front (both) and 11'' rear. The rear is a special jeep-only wiper blade that you have to get at the dealer. The front wipers are available aftermarket. See sources and related links below for more information.

That is the right size but what i use on my jeep liberty is a 22" on the front and 12" on the back, and i can see way more then i could with the 19" on the front and 11" on the back..

Low side.

Low side.

It should come on when you turn on the ignition without starting the car. If it does not the bulb is blown or it has been disconnected. Some unscrupulous sellers do this before selling a car with emissions problems where the light is on. If you just bought the car, have the bulb checked and if you find after replacing the bulb or connecting it, the light stays on demand a refund or repair of the problem from the seller. Get written proof of the condition of the bulb. If they refuse contact your state Attorney General for advice on what to do. It is illegal to sell a car with a non-functioning MIL (check engine light).

It is probably low on transmission fluid. Check transmission fluid level only with a warm engine after it has been run about 5 miles or so. Checking this when the engine is cool will give false readings.

They're not actually tweeters. They are a unique speaker size. There is a Blaupunkt 3 1/2 speaker that fits with little modification. Hunt around google for blaupunkt liberty tweeters.

If its a 4x4 and 3.7 there are 4 snesors. 2 on each side of the motor. That is what I have. I am changing the ones before the converter today.

Most likely.

First make sure that the service brakes are adjusted properly

Emergency brake adjustment should be either at the junction of the cables under vehicle or at the handle itself (may have to remove trim for access) Set handle at 3 clicks brake should hold at this point

nope the 3.7 has a timing chain...last much longer

Trouble code P0463 means: Fuel Level Sensor A Circuit High Input

Check your owners Manuel, If it has the towing package with the class3 hitch its 5,000lbs.

There is a malfunction in the "chip" key system.

The Jeep Liberty is equipped with a Tire Pressure Monitoring System (TPMS), and a light on the dashboard that looks like an exclamation point will light up if one or more of the tires on the Jeep is significantly under-inflated. You should check the air pressure in all of your tires, and make sure that each tire is properly inflated.

it is located on the left of the oil filler cap.Pull the vacumm hose of and turn counter clockwise,then pull out.

well in side of the jeep in the back pull the plastic off and on the left side were the handle is there is a whit leaver pop that to the other side and then pull handle that is what i just did to my moms jeep.

underneath dash near steering column attached to linkage from master cylinder

Just unscrew the two hex screws.Pull tail light out.locate bulb assembly and twist then remove bulb.Replace new bulb.Put back in reverse order.

price of a new battery for a jeep liberty sport 2006

Yes, a 2003 hitch will fit a 2005. If you look at Liberty hitches for sale online, they state they fit 2002-2007 Libbies.

# Raise and support vehicle. # Remove the wheel and tire assemblies. # Compress the caliper # Remove the caliper slide pin bolts NOTE: Do not allow brake hose to support caliper assembly. # Remove the caliper by tilting the top up and off the caliper adapter # Support and hang the caliper. # Remove the inboard brake pad (1) from the caliper # Remove the outboard brake pad (2) from the caliper # Place an old brake shoe between a C-clamp and caliper piston. Bottom piston in the caliper bore with C-clamp. # Clean caliper mounting adapter and anti-rattle spring guide # Lubricate anti-rattle spring guides with Mopar brake grease. # Install anti-rattle spring guides NOTE:Anti-rattle spring guides are not interchangeable. # Install inboard brake pad to the caliper # Install outboard brake pad to the caliper # Tilt the top of the caliper over rotor and under adapter. Then push the bottom of the caliper down onto the adapter # Install caliper to the rotor and then install the caliper slide pin bolts, Install wheel and tire assemblies and lower vehicle, # Apply brakes several times to seat caliper pistons and brake shoes and obtain firm pedal. # Top off master cylinder fluid level.