Jeep Liberty

Approx 5 quarts

I have a 2003 jeep liberty, i just got my rear brakes done. It cost me any where from 179.00 to 250.00. You can get it done cheaper, just dont let the brake place screw you over like they did to me.

Pass side 2-4-6

Driver side 1-3-5

The 2003 Jeep Liberty wiper blade sizes are 19" wiper blades on both sides front. See sources and related links below for more information. Since there are over 22 different wiper arm attachments, do not buy wipers just by length only - be sure to lookup exact wiper blade part numbers by vehicle make, model and year for the brand wiper you decide to purchase. This ensures correct length AND correct attachment.

Yes.

It depends on if you're talking front or rear. If it's front, get a Haynes Manual from Auto Zone for whichever year you have. If it's rear, you'll need a metric socket set and wrench - unbolt the pillars under the bench seat (there are four 10mm bolts) and it'll swing up to let you access the seat belt anchors for both male & female connectors. If possible, don't mess with new parts from the dealership unless it's under warranty. A reputable auto recycler will probably carry what you need for half as much and still probably have the right color.

Hope this helps, I just finished doing the rear seat belt anchor on my wife's '04 Liberty.

Brad in Tucson

I would assume ATF+4 because it's a dailmer chrysler product.....Walmart sells it in the super tech brand........They all have to meet certain standards; super tech is just as good as any other brand.

Back yard Mechanic (15yrs)

no. there are no adjustments on any mass air flow sensor

Trouble code P0174 means:System too lean (Bank 2)

I just talked with a man today about my jeep liberty and i asked him why did the fan come on and why it makes the noise of changing gears and he said that if the gears don't change it just keeps running that means a sensor is out or malfuntioned on it hope this helps but i wasn't in there for that. I was there for a wheel sensor out again.

5w30

5w30

The PCD is 5 x 114.3mm or 5 x 4.5 inch Regards wizard

Dodge uses the same 8 cylinder engine in the Ram pick-ups. The firing order for both the 5.2L and 5.9L V8s is: 1-8-4-3-6-5-7-2

I doubt they changed the firing order just for Jeep.

The Enhanced Warning System (BeltAlert) can be enabled

or disabled by your authorized dealer or by

following these steps:

NOTE: The following steps must occur within the first

60 seconds of the ignition switch being turned to the ON

or START position. DaimlerChrysler does not recommend

deactivating the Enhanced Warning System

(BeltAlert).

1. Turn the ignition switch to the OFF position and

buckle the driver's seat belt.

2. Start the engine and wait for the Seat Belt Warning

Light to turn off.

3. Within 60 seconds of starting the vehicle, unbuckle

and then re-buckle the driver's seat belt at least three

times within 10 seconds, ending with the seat belt

buckled.

NOTE: Watch for the Seat BeltWarning Light to turn on

while unbuckling and off while re-buckling the seat belt.

It may be necessary to retract the seat belt.

The bulb probably just burnt out.. I'm not sure how to change it.

You can reset the oil light by scrolling to the oil life display. Once on the display, hold the scroll button in until the oil life goes to 100 percent

11"

The door stoppers have tension loaded ball bearings in a small case that press against the top and bottom of the plastic-looking bar between the body and the edge of the door. The pressure level is fairly substantial. The plastic is grooved (in which the balls slide) with extra depressions in two spot to hold the door partially and fully open. If the door is making "popping" noises, this would indicate that the plastic is wearing on the slide and the balls are essentially 'popping" into those depressions. To lube, I have used lithium spray grease around the pivot pin on the body side and directed above and below where the slide enters the door but even taking the slider out and cleaning it well has not had an effect on the"popping" at this point - it's more of an annoyance but the stoppers can be replaced for about $30 + labor if needed.

Turn ignition switch to "ON" position. Depress and release MENU push button until SERVICE INTV = is displayed. Press and release STEP button to step through available options

You probably have a faulty blower motor resistor. I believe it is located on bottom of heater box. This I also believe a dealer item.

No

No

The seat belt chime can be enabled or disabled by following these steps. Note: The following steps must occur within the first 60 seconds of the ignition switch being turned to the ON or START position. 1. Turn the ignition switch to the OFF position, and buckle the driver

Chrysler decided to make it a special tool only available to the dealer.

If you read the other jeep forums and listen to the dealer they will tell you things like it has to be done just so and at just a certain temperature yada yada . Well after owning an 07 since it was new I have taken it in many times for a "free trans level check" I do it just to be a pain in the but. Because I have watched them over and over. and all they do is stick a dip stick in the hole with it idling and in park. I did not see them take any temp or do anything special. I have rebuilt trans missions man and auto many times over so I know them. This is a bull-s ploy to get you in the shop as often as possible.

Low oil pressure

they are controls for the sound system. right hand controls volume and mode (press middle to change modes), left control varies depending upon which "mode" you are in . try checking owners manual