answersLogoWhite

0

Jeep Wrangler Sahara

The Wrangler Sahara was a compact sport utility vehicle produced by Chrysler for its Jeep division. This model featured trail cloth seats, alloy wheels, body color fender flares and bumper fog lamps.

1,201 Questions

How does a fold and tumble passenger seat come off in a 97 jeep wrangler?

Access the back seat from the tailgate. On the left there is a lever - lift it up, push the top of the seat forward. Be careful of the carpet and your fingers while doing this. Tip the entire seat forward. The next part isn't pretty, it just involves strength. Slide the entire seat to one side and the pin should slip out of the bracket. Lift the free side up and slide it the opposite way. Then it's brute force to get it out.

Make sure you remember which holes the pins go back in.

How do you flat tow a jeep wrangler 4x4 automatic?

Place the transmission in Park and the transfer case in neutral.

What would cause a tapping noise in a 1999 Buick Century 3.1 liter engine?

I ask the same question to GM and they told me that it is a cold motor piston slap and should go away once the motor is warmed up. The garage told me that it is normal and not to worry.

How do you fix a door latch that's stuck and the door wont shut?

how do you fix a prosthetic leg that the release screw wont go all the way down in to the socket

What kind of tool is needed to take the filler plug out of the manual transmission of a 1988 Jeep Wrangler YJ?

well it's not a 3/8ths or a 1/4 so I made my own. I found that a hole punch with a square shaft fits perfectly. I cut it iff about 1/2 inch long and set into a 9mm socket. I had enough material to make about 4 "tools"

How do you adjust the headlights on a 2002 Sonoma?

There should be adjustment screws on top of the housing for the headlights. You need some of those sockets that look like they are Allen wrenches, but have like a star on the end. They come in a few sizes but the sizes are like T15 T20 T25. something like that. Otherwise you can use a pliers or something like that to turn them. clockwise to move the lights down, and counter clockwise to move them up I believe.

How do you reset the change oil on a 2007 Jeep wrangler?

You're not going to believe this, but it worked on my 4-door Jeep Wrangler Unlimited. Insert ignition key. Turn one click. Press the right-hand button on the instrument panel -- the one just below the odometer, which you would normally use to track the miles of a particular trip. With that button still pressed down, turn the ignition key one more click -- not so that the car starts, but so that the radio could come on, etc., etc. Every light on the instrument panel should now light up, and all the instruments should run through a complex test pattern that you've never seen before. While that test pattern is still running, or perhaps just after it's finished, depress the gas pedal three times in rapid succession. Now start the car; the "change oil" message should be gone. You don't need to all that stuff to reset the indicator. The correct process to reset the oil change indicator system (after

performing the scheduled maintenance) is: 1. Turn the ignition switch to the ON position (Do not

start the engine).

2. Fully depress the accelerator pedal slowly three

times within 10 seconds.

3. Turn the ignition switch to the OFF/LOCK position.

NOTE: If the indicator message illuminates when you

start the vehicle, the oil change indicator system did not

reset. If necessary repeat this procedure.

What is the smallest rim size that will fit on a 2008 Jeep Wrangler jk?

A 15" wheel is the smallest that will fit. However, not all 15 inch wheels will, only certain ones. Many make contact with the brakes and will result in you having to grind the calipers to make them fit. Do some research on the wheels you like beforehand to assure they will fit correctly.

How do you replace a headlamp relay in a 1994 Jeep Wrangler YJ?

I believe there is no relay in the 94 YJ.... the power is regulated throught the switch.

Can rips in a jeep wrangler's soft top be fixed?

Yes, it is possible to stick the rip/s with thread using your hands or a sewing machine.

How do you change the wiper motor on a 1995 Jeep Wrangler?

Take the wiper arms off. Then undo your windshield so that it folds down onto hood. Remove the three screws holding the wiper motor on. disconnect the wiper drive link. remove the wire clip from bottom on the windshield frame. Take out the 4 screws on the bottom of windshield that hold on the seal. (they get in the way of pullin the motor out). Pull the motor and link out through the access hole. Pry the link off the motor pivot. Do not remove the crank arm adjusting nut though. That's it. Sounds way harder than it is.

What is the stock gear ratio for the rear of a 2000 jeep wrangler Sahara?

There are four ways to find a ratio.

1 A dealer can normally tell from the vin number.

2 There are normally tags or labels on the axle that have part number, gear ratio, and fluid requirement

info.

3 You can count how many times you have to turn the driveshaft to get one complete turn of the tires.

4 You can divide the number of teeth on the ring gear and divide by number of teeth on the pinion.

How do you remove the front brakes on a Jeep Wrangler?

If you are replacing the pads or rotor on a 1987-1990 here are my thoughts:

  • Tools needed- 17mm hex socket, Large Clamp, flathead screwdriver, small wood block, rubber mallet. (Note; some calipers may have standard heads)

Step1:

  • Remove brake reservoir cover and tire(s) then remove caliper using 17mm socket counter clockwise (you may need to tap socket to seat properly. Back out screws- on the drivers side caliper tap or use leverage bar from the top of caliper and push toward rear of jeep- this will Free the caliper from the top and then it release the bottom of caliper form the support. Use a hanger or something to suspend caliper from frame (careful not to damage brake lines). This procedure is then reversed for the passenger side caliper.

Step2:

  • Removing Worn Pads: There are two metal clamps on top and bottom of pads. Take the screw driver and carefully lift the clamp ends/tips so they rest on the support (note clamps do not have to be removed, unless damaged)- Now remove pads (this is a good time to inspect disc and clean area and apply a small amount of Lithium grease on support where caliper ends sit (this will allow pads to slide easier). Now take your C-clamp and wood block to reset or push back caliper piston. Place wooden block on the inside of caliper (where the pads sit), then place C-clamp between wood and outside of caliper (make sure reservoir cover is off) and slowly twist clamp until piston is completely pushed in.

Step 3: Installing New Pads: Install is reverse of removal- Smaller pad rests on the inside or engine side of support. (Note: you may want to add brake silencer grease to the metal part of pads to reduce squeaks, etc). Once pads are rested, take screw driver to replace metal clamp end/tips- these hold pads in place.

Step 4: Reinstalling Caliper: Reverse of removal (driver's side: rest bottom of caliper on support, then swing top caliper in place. Tighten hex screws.- remember passenger side is reversed).

Step 5: Check Brake reservoir for correct fluid level- add DOT3 fluid if necessary. Replace cap-

Step 6: Install tires and start Jeep- Pump brakes- if peddle feel is soft or drops you need to bleed your breaks.

Option#1: Bleeding Brakes: It's best to removes tires for easier access- Two ways to precede (1) Buy a brake bleeder kit or (2) Do this manually with another person. - Manual instructions: Bleed Passenger side first: Tools needs 7/8" socket: Now- open bleeder valve w/ socket w/ a half turn (fluid should come out- Have one person slowly push the brake peddle to floor and have them hold that position until valve is tightened- do this 3 times to get all the air out. Use same procedure on driver's side and now you are done!

Option #2: Rotor disc removal: If your discs need replacement follow steps 1 & 2- Once old pads are removed the disc should simple pull off with little effort- Installation is reverse of removal.

!

remove the tire, carefully push the capilar in with a screwdriver. on the back of the brack claw are 3 bolds: the upper and lower are size 13, the middle with the brake hose atached to it is size 14. to remove the claw unbold the size 13 bolds, pull them out and remove the claw by lifting and pulling back. once the claw is out you can remove/install new pads. if you need to remove the claw to rebuild or replace, you need to unbold the middle size 14 bold. when re-installing you should used 2 new copper whashers.once the claw is removed you can also remove the disk simply by pulling it of the hub.

How do you open rear window for Jeep Wrangler hard top?

On my Jeep Wrangler, I have to open the tailgate first, then just lift up on the window.

Where can you find a Chevrolet suburban rear passenger sliding seat drawing?

You can find a Chevy suburban rear passenger sliding seat drawing at most local libraries. You can also obtain the drawing from most Chevrolet dealerships.