Oldsmobile Cutlass

There more than likely aren't any. Modern automobiles use sealed units that are non-serviceable. Your owners manual should list grease points if there are any. Of course you could just look at all suspension parts to see if there are any grease fittings.

CAPACITIES
Engine, with filter..........4.6 qts
Cooling System, Initial Fill..........13.0 qts
Automatic Transmission, Total Fill..........13.0 qts Hope This Helps.

The horsepower for a 1994 with the 3.1 engine is 160. It will do 0-60 in approx 9.5 secs.

It is hidden in the dash on a the passengers side. To locate it u must open the front passengers door.

Possibly burning oil. Check compression.

yes it will if it is a 4T60E from a 3.4 DOHC and yes it will if it is from the 3.1 even though it may not i know this because i am an olds nut and i have a 96 3.4 DOHC and that is the only year in the 90s that will not enter change with the others in the case of your 93 the 95 tranny will fit as long as it is the same tranny you may have to switch a mounting bracket on the cradle but again yes yes yes is the answer you seek

Not too familiar with that engine, but never use a hammer to press it on. Go to your local Kragen, Shucks or autozone, they have a harmonic balancer installer in which you can rent. It simply screws into the center of the shaft and evenly presses the harmonic balancer onto the crankshaft.

The P1406 code on a 1996 Oldsmobile Cutlass Ciera 3.1 is the code for the EGR pintle position circuit. I know this because it was my question initially and we bought a code reader to check the problem. It is a factory specific code, so the answer is quite specific. Good luck !

I believe you need to pull the steering wheel off and get in the steering column that way. I had this done on a previous car, (expensive) so this time I just hot wired to the starter and added a tago switch.

number one is closest to the radiator... read up

everyone should have a manual for their vehicle, and the library should have a professional manual available...in the reference section, you'll have to make copies of the important sections...good luck :)

* Looking from the front of the vehicle, the number 1 cylinder is on the rear left side(near the alternator) & the firing order is: 1 4 6 3 2 5... Taken from the Haynes Repair Manual #38010.

be more specific money, lowrider, race car,or in what way..

The thermostat is located where the hose leaves the engine to go to the top of the radiator. You unscrew the bolts holding the hose mounting to the engine. There you find the thermostat.

Behide the passengers side air bag

The 1993 Oldsmobile Ciera with the 3300 V6 (code 'N') is specified for 10W30. 5W30 can be used is severe service/winter conditions. The service fill capacity for the Ciera is 4.5-quarts with the filter.

where is the emc located on a 1988 olds cutlass?

If the flashers work, change the fuse. It is located behind the ashtray/cigarette lighter area. You'll need to remove the cover, the fuse was a pain for me to locate when I had to change mine. But that is where mine was, and that fixed my problem. Hope this helps you.

Under the drivers dash to the left of the steering wheel.

What bolt pattern are you talking about? The wheels? Is it front or rear wheel drive? Rear wheel drive will be 4 3/4 inches measured from the center of one lug stud, skipping one, to the outside edge of the next lug stud. This is measuring across the center, NOT wrapping the tape around the outside of the skipped lug.

Follow the top radiator hose down to the water outlet on the engine; the stat is in there.

Assuming you're referring to the 4-door sedan model, the rear windows were fixed in place on that bodystyle (1978-87) - hence their being no crank to wind them down.

Which mirror? Just guessing you mean the door mounted mirror. Remove the inner door panel. There will be two nuts holding the mirror on. Remove them and pull the mirror off. If you mean the windshield mounted mirror, there is a small Allen or torx screw holding it on. Loosen it, slide the mirror up and remove.

The firing order for a 1990 Olds cutlass supreme 3.1litre is 1, 2, 3, 4, 5, 6. The number one cylinder is closest to the pulleys on the left as you face it.

You can't, its done by the computer if you have a knock noise, replace the knock sensor. its locate on the back of the engine near the alternator.

There is plenty of room if that's what you want to know.

Simplest way to do it is to lower the engine and trans into the car together and align the trans to the tail shaft mount. Put a level across the valve covers, then mark where the motor mounts will need to be and remove engine and trans to install the mounts.

Headers from a Chevelle should work.

Inertia is the resistance of motion of an object. The more inertia, the harder it is to move something. The less inertia, the easier it is to move. Take a bowling ball and a marble. The marble can be flicked by the finger, because it has less inertia. The bowling ball takes the entire hand because it has more inertia than the marble. According to Newton's laws, an object that is moving tends to continue in motion. A moving object has inertia as it has Mass and Velocity. An object that is not moving requires a Force exerted on the Mass to start it moving.