0
Oldsmobile LSS
The Oldsmobile LSS was a four-door sedan produced by General Motors. The car was a rebadged 11th-generation model of the Oldsmobile 88. It featured a 3.8 L Buick V6 engine, 110.8 in (2814 mm) wheelbase and front-wheel drive.
105 Questions
Where is the fuel pump on a 1994 Oldsmobile eighty eight?
On a 1994 Oldsmobile Eighty-Eight, the fuel pump is located inside the fuel tank. To access it, you'll need to remove the tank from the vehicle, which typically involves disconnecting the fuel lines and electrical connections. It's also advisable to relieve fuel system pressure before attempting to remove the tank. Always consult a repair manual for detailed instructions specific to your model.
Where is the fuse for the lighter on an Oldsmobile royale 88?
The fuse for the cigarette lighter on an Oldsmobile Royale 88 is typically located in the fuse box, which is usually found under the dashboard on the driver's side or in the engine compartment. You can identify the specific fuse by checking the diagram on the fuse box cover or referring to the owner's manual for the exact location and amperage of the cigarette lighter fuse. If the lighter is not functioning, make sure to inspect the fuse for any signs of damage or a blown filament.
1997 Oldsmobile how to remove mounting device button on rear view mirror when there is no set screw?
To remove the mounting device button on a 1997 Oldsmobile rearview mirror without a set screw, gently pry off the plastic cover that may be concealing the mounting mechanism. Once the cover is removed, look for a small clip or a spring mechanism that holds the button in place. Carefully push or release this clip while simultaneously pulling the button away from the windshield. If needed, use a flat-head screwdriver for leverage, but be cautious not to damage the glass or surrounding areas.
What car uses STP oil filter s3506?
Oh, dude, the STP S3506 oil filter is compatible with a variety of vehicles, like a bunch of cars and trucks from different manufacturers. It's like a universal oil filter that fits a range of models, so you don't have to stress about finding the exact one for your ride. Just pop that bad boy in and you're good to go.
It is used by many vehical models as a sub-model of the vehical (Impala SS, Mazda Protege ES, Boniville LS...etc.)
With the Oldsmobile, the LSS was originally going to be a sub-model of the Eighty-Eight. The LSS became a stand alone production (Proud Owner =) ) branching off of the Eighty-Eight.
When becoming an LSS, certain upgrades need to go into effect to do so. Evolving from the Eighty-Eight to the Lss, the susspension was stiffened to give a more sporty ride (while still maintaining a smooth cloud like ride) and upgrade handling abilities. The engine remained the same (3.8L V8) producing 225BHP and 240LB Torque; but, the LSS had the option for an upgrade to a supercharged version of the same 3.8L engine-now producing 240-250BHP and 280LB Torque. The LSS had many other various upgrades, but that is not what this question is about.
Back on topic... LSS=Luxury Super Sport.
97 Olds 88 fuel gauge brokenany ideas?
You got to change the fuel sending unit which involves dropping the fuel tank , aint really a bad job if you have a lift
My fan blade is positioned too close to the housing. Whenever I would pull on the fan (from under the passenger side dash), it would start up.
I have had continual problems with the heating and fan operation of my car.
It is the last Ford that I buy because of the continual problem.
chk to see if yu have it positioned in the fan housing correctly , yu may have it in the worng position and causing it to be tilted the worng way , its an easy mistake to make
How do you replace a belt tensioner pulley on a 1996 olds lss?
It has a bolt at the center of it' BE AWARE that this bolt is reversed threaded, that means the direction normally used (right, is counter clockwise) to loosen , and left is "clockwise"to tighten, therefor when removing the bolt you go in the direction of tightening to remove it, the reason for this application is that the bolt is used to releive the tension on the serpentene belt to take it off for replacement.
What happens if the transaxle range sensor goes bad?
what happens if the transaxle range sensor goes bad?
How do you replace a idle air control valve on 1997 Oldsmobile lss?
If you know the location you need a TORX bit, there are only 2 screws there, remove the wire first, this usually is very simple. You should also clean the inside area with carb/fuel injector spray as well as the throttle body for the best results as there may be some oil in there at times.don't use too much at one time as it will make it start hard at first, does this help?
Where is Engine Control Computer located on a 1994 Delta 88 LSS?
Clipped to the firewall, passenger compartment, just above where the passenger's feet would be. Remove the plastic cover (I think 7mm bolts) and you'll see the bottom of it.
Fuse box location on a 1999 olds 88?
On the drivers' side above left foot, it has a cover on it with a pulldown on it, it has 2 little inserts to keep it in place that go in the direction of the glovebox, it easily drops down when you use the elevated grip, also be aware that thre are othe relays and fuses hiden on the right side kick panel that are easily accessed, but no information is put there for whatever they are there for, but the one you are looking for does have the applications for each fuse and the 2 circuit breakers there
How do you change headlights in Oldsmobile 89 delta 88 royale?
Pop the hood and look at the back side of the lights, the outside ones are the normal headlights, the other light in the clear case will be your brights. Pull out the wiring connector - the gray thing with 2 wires going in it. There will be a black plastic lock ring that you turn counter-clockwise to unlock. Pull out the headlight and replace it. Then put the lock ring back on (good luck with that one, I'm having a hard time getting mine back in). Last, just put the wiring connector back in. For the passenger headlight you'll need to take your battery out. For the battery removal you should need a 8mm wrench for the terminal bolts and a 13mm ratchet and extender for the bracket.
