Small Engines

Yamaha golf cars are made in Newnan, Georgia. Yamaha electric golf cars are 95% made in the USA and the gas cars are 88% made in the USA. Most all of the car is built by Yamaha in their plant in Georgia.

Other brands of cars are basically no more than 66% built in the USA making Yamaha the more American cart.

the year is 2000

my g2 runs full when you step on the pedal and is very touchy when going slow when looking for a ball and sometimes when its is warmed up it will backfire first before it starts running.

at least 4.10 for small one depnding on the sizes 5 feet is basicly all you will need

To convert cubic inches to horsepower, you typically need to know the engine's efficiency and design, as horsepower is not solely determined by displacement. However, a rough estimate is that 1 cubic inch can produce about 0.5 to 0.6 horsepower in a typical gasoline engine. Therefore, 110 cubic inches might yield approximately 55 to 66 horsepower, depending on the engine's specific design and tuning.

1. Remove cover from top of the motor (depending on the motor the recoil is attached to it) should have three bolts. When the cover is off you will see a fly wheel with a recoil clutch (or just a nut if the recoil is not on top). Take a pry bar or large screw driver jam the fly wheel with it (make sure you do not damage it). Use a pipe wrench or gently tap the recoil clutch loose with a hammer. Then take two pry bars and pry on the bottom edge of the fly wheel ( be carefull where you pry find two solid spots on the case)the fly wheel should pop off if not keep the pry bars prying and get a piece of wood and tap the end of the nut shaft this should knock it loose. Now you should be able to see the points and condenser. Take the screw off the pivot point on the points and take the bracket off the condenser. Once you put the points and condenser back in put the points at the open position - make sure the condenser is not tightened - put a piece of cardboard (about the thickness of a cigarette pack) between the points and gently push the condenser until it just touches the cardboard and tighten the condenser bolt. Then put it all back together again.

The best wheels for a soapbox racer are typically lightweight, durable, and provide good traction. Many racers opt for rubber wheels with a diameter of around 8 to 12 inches to balance speed and stability. Additionally, using wheels with a smooth tread can help reduce friction and increase speed on flat surfaces. Bearing quality is also crucial; high-quality bearings will enhance performance and ensure a smoother ride.

Usually a dirty carb ,but an inproperly adjusted carb can do it also .

I'm not sure but might be 40 to one?

It depends on what you need - if you want lots of speed no power on the bottom end you go with the high ratio - if you want lots of torque on take off and lots of pulling power you take the low gear ratio.

I work at a Go Kart Repair Shop and the current age limit to drive a go kart around a neighborhood area or similar scenario is 13 years of age. As long as you can drive the vehicle safely, you are good to drive a go kart. I hope this helped you in your needs.

The shifting fork is on the right side of the under the right engine cover . If it is electronic shift , when you push the button it rotates the shifting fork to go into gears . The bottom arm of the shifting fork is bad about breaking . In a pinch I have welded it back on but for the price its better to replace it .

count your teeth on your ring gear <big gear> and on you pinion <little gear> and the divide the ring gear teeth by the pinion

can i make a raptor 50cc any faster. can you bore cylinder out and get more power out of it

500

its 40:1. Check the specs for this saw at: http://www.acresinternet.com/cscc.nsf/ed1d619968136da688256af40002b8f7/801048d6175e831988256b6b00189180?OpenDocument

The top speed of a stock Yamaha Warrior 350 is around 65 to 70 mph. I own a 1998 Warrior 350 and it will go 68 mph. The top speed has not changed more than 5 mph from the time it was introduced until today...

I have a 2000 warrior 350 that has been clocked at 117mph and all it has added on is stage 2 carb jets and K&N air filter.

.020

U can only check the primary side,not the secondary side. Had same problem, changed coil and it worked, but its a crap shoot. If u have problems check ur points first, this is a mojority of the problem!

Hi I have a 2005 3010 transmule and it is in the shop right now needing a wiring harness. They put on 3 new fuel pumps and it burned them up. I wish you luck, they want $1,100 to put in a new wiring harness.

yes

It depends on a few things.... age of saw (15-20 yrs+ older=richer), how hard the saw is going to be working (a tad richer for really big jobs), etc, but probably 50:1 will work well for you.

Frame number is located below gear shifter,slightly forward on bottom frame rail. Engine number is next to cylinder,exhaust side of engine,below exhaust

it is made out of wood and medal.

the vaulve tourk on a 220 bayou should be enougt to make the quad run