0
Suzuki Samurai
The Suzuki Samurai was a rebadged second-generation variant of the Suzuki Jimny manufactured from 1981 to 1998. The car was available as a two-door sport utility vehicle or two-door convertible. It featured a front engine and rear/four-wheel drive.
429 Questions
What size bolts hold the spare tire carrier on a suzuki samauri?
If you are wondering about the thread size, they are the same as the Lug Bolts. 12x125 MM.
On my 88 suzuki samurai Where is the diagnostic terminal of the fuse block located.?
Jim Duquette
Oklahoma city, OK
Gusthedog2.net
How do you replace a wiper motor in a 1990 suzuki samurai?
the best way is to unbolt the windshield and fold it down on to the hood. under where the windshield meets the body is where all the wires and stuff is at. its about a 30 min job.
What year did they stop making z24s?
half way through 2002.....then they started calling them LS and so on.
What to do with noisy input shaft bearing on an evo 6?
Any bearing making noise more than likely needs replacing.
Any bearing making noise more than likely needs replacing.
What is the weight of a 1987 Suzuki Samurai?
roughly 2200 lb IIRC. I had an 86, that when fully loaded (er, overloaded) for a week's worth of camping in the Mojave Preserve, weighed in at 2900 lb...with all my gear, half a tank of gas, and me.
Will 235 75 R15 tires fit on a Suzuki Samurai fwd?
If you mean stock, no.
With maybe a 2" to 3" lift and a little trimming in the wheel well to prevent rubbing, it will fit fine.
Why does my rebuilt Sumo II Suzuki Samurai engine still use up oil after 8000 miles?
i don,t know but mine is the same it takes a quart after 600 km. i,m sending it back to where i got it rebuilt
How do you replace the clutch in a 1986 Suzuki Samurai?
Because the transmission does not drop free of the crossmember, pulling the engine is generally the best. Placing a 3/4" thick piece of wood under the bellhousing for support before removing the engine, will hold it in position for refitting.
Why does my brake pedal bleed done it won't hold pressure?
Probably either from air in the lines or the master cylinder leaking and in need of repair before the brakes go out entirely.
To tell the difference, if you pump up the brakes and hold pressure on the peddle and it stays up and then you let off of the peddle and it goes down, it is probably air, bleed the brakes.
If after pumping up the brakes and holding pressure it slowly leaks down, you are either losing fluid somewhere or the master cylinder internal seals are bad, fix them before the brakes are gone when you need them.
Why does your samurai 4wd dash light go out when idrive?
The 4WD switch is located in the transfer case. It is possible that you have a broken wire that is making intermittent contact.
Download the FREE Suzuki Samurai Shop Manual from http://www.suzukiinfo.com/
or visit zukikrawlers.com
zn
Where is the drain plug on the engine block for a 1987 suzuki samuria located?
Bottom of Oil Pan.Cheers Joseph
Will 2005 jeep rubicon rims fit on a 1987 Suzuki samurai?
I do not believe they will.
The newer Jeeps are bolt pattern 5 lug and 4.5 spacing.
This is commonly referred to 5 on 4.5in.
The Suzuki Samurai is 5 on 5.5in. (139.7mm).
The older Jeep wheels will fit because they used to be 5 on 5.5in. (139.7mm) (1946 to 1985).
What are the Suzuki samurai valve adjustment specs?
Hot adjustment on the 1.3 engine is .009-.011 clearance on the Intakes, and .010-.012 clearance on the Exhaust valves
What year they stop making Suzuki Samurai?
They stopped importing it into the US after the 1995 year model.
What is the head bolt torque specs on a samurai?
Head bolt specs for the '86 Samurai are 46 to 50.5 in. lbs.
How do you fix Suzuki samurai fuel gauge?
99% of the time replace sending unit in tank----very common problem on sammis
Does a 1987 suzuki samurai have a hydraulic clutch?
No, all of the sj410 and samurais are mechanical cable clutchs. The adjustment for pedal free play can be found on a bracket on the passenger side of the block, just behind the motor mount.
lets assume that all tests have been done. ie. presence of emissions in the cooling system. cylinder leak down indicates hi leakage into cooling system ect. if these tests prove these theorys then cylinder head service will be needed. further testing of the head will need to be done after removal to determine the cause. however lets keep it simple.is there exessive consumtion of coolant? humidity and cold temperatures can cause this sign of milky oil in the cap and is no indication of falty or "broken" car.
Two steps shold be followed with all suzuki products: 1. Drive car into the largest body of water you can find. 2. Buy a Honda or Toyota.
Ta dum ching! Thank you, thank you I got a million of em....
But seriously...you need to consider that loss of power and address it alone. If the car is not overheating, then ignore the goo in the cap. Certain climates are worse for this than others. Try to fix the drivability problem first, and it will lead you back to the head if its bad.
Sounds like all the previous answers are possible. However, if you get to removing the cylinder head it is always worth getting it pressure checked as these heads do have a tendancy for going porous due to rubbish grade aluminum being used in the casting process. this gives the same symptoms as a failed head gasket. they can be welded as a repair, but may well end up in the cylinder head needing replacement.
Where is the position of the VIN number of suzuki samurai?
on the drivers side of the vehicle. on the side of the dash. or just look at the inspection sticker.
