0
ATVs
ATVs are all-terrain vehicles, also known as "quads" or "four-wheelers." Ask questions about these recreational vehicles here.
2,162 Questions
How do you tighten rear axle nuts the right way?
All nuts and bolts for any vehicle has a torque spec( for a racher I think it's 47 ft-lbs.). from the manufacturer a torque wrench is the suggested way, but everyone I know just uses a 1/2 cordless impact gun.
1. chassis and body
2. engine
3. fuel system
4. cooling system
5. ignition system(for s.i engines)
6. electric system
7. transmission system
8. steering system
9. suspension system
10. braking system
11. emission
What are Mx vs ATV unleashed cheats?
brokeasajoke-millione bucks
minimoto-mini bikes
wardrobe-clothes
toolazy-everthing
How do you do a boot replacement on the rear axle of a 2001 Polaris Sportsman 400?
remove axle bolt from spindle and push it through you may have to remove spindle if no clearance. remove factory tie strap clean and grease before replacing with new boot reassemble in reverse watch for pin on nut threads reversed on passenger side always consult technical manual and follow safety protocols
How do you do a backflip on mx vs ATV reflex ds?
you press l and r at same time while licking your shoulder it only works if you lick your your shoulder so that the peter panda dance
How do you install an ignition bypass switch in an ATV?
How do I put a New key in ignition into it for 90 mL for speed Baja for Willer I lost my keys
Where is the model number located on a suzuki ATV?
i have a Suzuki LTA50 and the model is located on the steering column, or yolk , or whatever you want to call it
Where is the idle adjustment screw located on the 2005 Yamaha Kodiak ATV?
take the side pannel off and there is a knob on the end of a rubber tube that does this for you. turn right or left to get the Idle that you want.IF it is missing or has fallen off it will be on the left side and towards the front to bottom of the Carb.Good luck.
How do you make a Honda 250ex four wheeler louder?
Get a new exhaust, you probably want to look at FMF exhaust but if you get one too big you might have to get it jetted or it wont idol
What weight of oil for a 1986 Honda 125cc ATV?
I just called a Honda ATV dealer and asked him what oil to use in a 1982 ATC 110
he says 10w40. He says 10w40 was standard back in the 70,80's.
What is the position of a choke on a suzuki quadrunner ATV?
Just to the right of the LH grip you have rotating choke lever. All the way up is no choke, Rotated all the way down is fully choked.
How do you change the coolant on a 2001 Yamaha grizzly 600 ATV?
The 2001 grizzly 600 ATV is "Air Cooled". There is no coolant. The little radiator in the front is an oil cooler.
Maintance of Yamaha 250 quad ATV what oils do i use in a moto 4 250cc?
how to change rings on yamaha moto 4 250cc
Can you find out the year model of a YZ125 just by looking at the VIN If so how?
The tenth character of the VIN is the year character
Where to find a wiring diagram for polaris ATV 500?
this is the website i used http://www.quadtro.com/wp-content/uploads/admin/taller/pruebas/polaris/predator/500_2003/predatorspcs.pdf
How do you tell year model by VIN number on my polaris ATV?
To determine the year model of your Polaris ATV using the VIN (Vehicle Identification Number), locate the 10th character of the VIN. This character indicates the model year, with letters and numbers corresponding to specific years (e.g., 'A' for 1980 or 2010, 'B' for 1981 or 2011, and so forth). For a complete breakdown of VIN codes, you can refer to Polaris' official resources or other reliable databases that list VIN interpretations.
How do I test the CDI arctic cat 500 ATV?
To test the CDI (Capacitor Discharge Ignition) on an Arctic Cat 500 ATV, start by checking for any visible damage or corrosion on the CDI unit and its connections. Use a multimeter to measure the output voltage while cranking the engine; you should see a voltage pulse if the CDI is functioning properly. Additionally, you can swap the CDI with a known working unit to see if the ATV starts or runs better. If the ATV still does not run correctly, the issue may lie elsewhere in the ignition system or engine.
When making a gas oil mix for your Yamaha Blaster can you use sae 30 oil?
No, you can not use engine oil in place of two cycle oil.
What is the carburetor adjustment for 1984 Honda 200s 3 wheeler?
The idle speed screw is on the right side of the carburetor, just above the carburetor bowl (the lower part of the carburetor). Turning this screw clockwise will raise the idle speed. Turning it the other way will lower the idle speed, which is supposed to be close to 1400 RPMs. The other screw, or the air screw, should be turned in as far as it will go, then loosen it two and a half turn. If the engine runs well with this, then nothing more needs to be done. You can turn the last mentioned screw a bit more, clockwise, to adjust the air mixture. Make sure that the carburetor is clean.
What safety equipment is required to drive a 4x4 ATV?
There are a lot of safety equipment that you should bring with you when driving a 4x4 ATV. This includes equipment such as a shovel, a T-style lug wrench, gloves, pressure gauge, jumper cables along with general safety items such as water and a blanket to keep warm.
