0
Chevy Camaro
This category covers general questions about the Chevrolet Camaro, a pony car manufactured by General Motors and sold through its Chevrolet division. The Camaro was designed to compete with the Ford Mustang. Production of the model began in 1966.
4,208 Questions
What motor does a 1996 z28 camaro have?
its the LT1 don't confuse with the LT-1 from the oldschool corvettes because there not the same.
its a high compression reverse cooled 350 with aluminum heads
1998 Chey Camaro SS headlights will not switch to low beam it is stuck in high beam mode?
you will probably have to replace the headlight switch.
Where is the Map sensor is a 99 camaro?
On a 1999 Camaro, the map sensor is located on the back of the intake manifold. The intake manifold is the series of tubing that distributes the air coming into the engine.
How does a neutral safety switch work?
A neutral safety switch works by comparing the current in both the active and neutral conductors. When the current in both the active and neutral conductors is not equal the safety switch will trip. This works on the principle that the active and neutral are part of a closed loop and if there is an inbalance then current must be leaking out of the circuit. This leaking could be caused by faulty wiring, moisture (particularly in unused heating elements) or by contact from human or animal (ouchy)
A picture of the Chevy Camaro starter?
http://www.autopartswarehouse.com/mmp/chevy~camaro~starter~parts.html
How do you change the door hinge on a 1990 Camaro?
The '90 camaro has three bolts that hold the door hinge to the body and I believe three that hold the hinge to the door. The easiest way I've found is to score the position of the original hinge location and remove the bolts with the appropriate wrench with the door open. Be sure to have the door supported because it will try to sag. Once the new hinge is in place, align it to the original hinges location and tighten your bolts down.
How do you put a 350 short block in a 97 RS camaro?
you have to remove and install the motor through the bottom of the car by dropping the old one out, and lifting the new one in
How many Camaros came from factory with a 350 engine and a 5 speed tranny?
No camaro came from the factory with a 5 speed and a 350 the only way they could have both is if you did a swap and its worth it i did it in my 91 camaro rs and i love it! The iroc`s came with a 350 but they are all automatic.
One drain plug located in the center (bottom) of the radiator. It's not easy to get to but it can be done. If you cant get it just take off the bottom hose on the passenger side of the radiator.
How many 2011 camaros were produced?
Not possible to answer since they're still currently being produced
How get the starter off a 1994 camaro with the 3.4 liter v6?
theres two bolts that hold the starter in place and two wires that attach to the motor. Remove the nuts holding the wires and take note of where each go. then while supporting the starter remove the two bolts and it should slide right out as one piece.
Where is the ac drain tube on 1998 Camaro?
It is under the hood on the passenger side firewall down low.
Which is better the new or old camaro?
I would say old, (I like 89 models.) Plus you don't have to weary about the computer messing up on the new stile cars.
Use a maintance hole saw and drill a 3/4 to a 7/8" hole on each side to get to them. One hole will not weaken the subframe at all. Any hardware store or tool dealer will have them.
What would cause a 1995 GMC Jimmy to idle and run rough and the check engine light come on?
Mid 90's Jimmy's have issues with cracked blocks, at transmissions, the front differencial, as well as the oil: pan, filter, pump, and gasket. It is very possible that the block is cracked.
AnswerIt could also be carbon in the EGR valve... AnswerEarly 90's Jimmys has a multiport fuel injection system which used a fuel regulator and delivery system inside the intake maniford. The Central Port Injector(CPI or Spider) has had a tendency to leak from the regulator putting excess fuel into one side of the intake manifold. The single O2 sensor reading the combined exhaust trys to lean the mixture by shortening up the "on" time for all of the injectors which leans out the other bank of cylinders. In essence you have three cylinders running rich, three running lean. Not the best situation for a stable idle.The indication of this is that one side of the intake manifold will be relatively clean(usually a yellowish brown)from being cleaned by the gasolene, and the other side dirty from the blow-by products from the crankcase vent. Check out: http://www.asashop.org/autoinc/feb2000/techtotech.htmfor a expert diagnosis from an ASE Certified Tech with lots of pictures of what I was trying to explain. Look for "Jimmy CPI Unit" on EBay, they have some of the newer modified units for fairly cheap ($200), their not hard to change, just be careful not to get any dirt into the injectors when you remove the poppet valves at the end of each feed tube. That's about it if it's the CPI, hope it helps.94 AnswerI have gone through 2 EGR ValvesA few times a friend even cleaned one to get it going, It worked for a while but eventually failed. Answerits prolly the egr valve a piece of carbon is prolly holdin it open mine used to do that but i got a gasket made by timeco an it has a screen that stops the carbon from buildin up AnswerIf the check engine light is on, get an obd2 scanner and check out what code is stored in the computer. The scanner will tell you what codes showed up even if the light is now off. The code should tell you exactly what is wrong without guessing.How to change window motor on a 1997 camaro?
Pull off door panel. Roll window half way down. Un-bolt window. There should be four bolts on the door panel that hold the motor. Take the arm off the left on driver side or right on passenger. Then motor should just slide out of the hole.
How do you remove ignition cylinder for a 1997 camaro?
Disconnect the battery. Remove the steering wheel. Remove turn signal switch,Remove the buzzer switch with needle nose pliers. Then insert the key(make sure it is not in place beforehand) and place in lock position. remove lock cylinder retaining torx screw. Then with key in place, pull out the assembly straight out.Disconnect the electrical connector from the bulkhead connectorand remove retaining clip. attach some wire to the connector to help with installation and pull harness through column. Installation is reverse.
How do you check the transmission fluid on a 97 Chevy camaro V6 3.8 automatic transmission?
There should be a dip stick labeled on the passenger side of the car just pull it out and make sure you fluid level is where it should be
What is the turning radius of the 2013 Chevrolet Camaro?
The 2013 Chevrolet Camaro's turning circle is 37.7 ft..
