0
Chrysler LHS
The LHS is a four-door full-size sedan produced by Chrysler from 1994 to 2001. The car features a 3.5-liter V6 engine, and a 4-speed automatic transmission. It was based on the Chrysler LH platform.
543 Questions
Where is the heater core located in a 94 Chrysler LHS?
You have to remove the upper headers and it should be there toward the radiator and the fuel rail
It is on the left side of the block, only tools required are 13 and 15 mm sockets and wrenches.
Could well be a dirty fuel filter or fuel pump problem. I would check them in that order
How do you change headlights Chrysler lhs?
The headlight bulbs for the Chrysler LHS are inserted in the back of the light housings. There is a twist ring that holds them in, rotate the ring to remove and replace the bulb.
Where is oil pressure sensor or sending unit on 1995 LHS 3.5L engine?
I just got this changed on my car. The switch costs about 8 bucks at the local auto part store.Put the car on a lift or jack it up. right under the radiator youll see something that looks like the plug you just bought. un clip the old one put the new one on. its in the gap between the radiator and oil pan.
What will cause a overheating on a chrysler sebring jxi 1998?
I had the same thing happen to my 96 sebring and it turned out it was my radiator cap had lost its seal so took it to jiffy lube paid 8 dollars they put it on no problem since
Fuel safety shutoff 97 Chrysler lhs?
Chrysler does not use inertia switches. The fuel system is computer controlled with relays.
How do you fix a off track window on my 2000 Chrysler lhs?
Pretty simple actually, first of all remove all the retaining screws there are approx 6-8 with a phillips screwdriver, trick no 1, door handle there is a plactic insert in the middle remove it and there is a screw behind it, remove the metal grill that covers the speaker in the door, you will find 3 screws hidden in the panel remove them, ok now, with all screws removed the door handle has a plastic lock on the insert itself remove it by prying carefully outward and then twist it, if it breaks (you can replace it thru a parts store) it retains the lock rod in place, very carefully pry up on the window switch and remove it then unplug it, follow the rest of the wires ie speaker, door courtesy light, auto locks, make sure you unplug all the wires the door panel will not come off, and out of the way, if you dont, next remove the 3 screws at the very bottom of the door panel after this pry out on the panel and lift up to remove it, there may or may not be a rubber shield covering the entire area, if so remove it, it has black pliable rubber from the factory that can be re-used, also remove it, isknown as adoor sound deadner, with all this out of the way you are ready to fix your window, roll the window down approx 1/2 way and you will see 2 clamps that hold the window into the track with 2 10mm nuts, determine which retainer is bad remove both nuts and push the track out of the way, very carefully lift the window out of the track and pull up and out to remove it completely from the door, ok, now with window out on the bench, you will have to (very carefully) unseat the retainer from the glass, do this by using a thin bladed knife or razor knife, take your time it is sealed with non pliable calk and it can be difficult, to remove, take a piece of wood with a hammer and drive the clip off the glass, taking extreme care not to strike the glass, then install the new retainer , make sure you crimp the bracket a little tight and then redrive it back into place very easy, then re install the window back in the door, line the window in its tracks and let it back down (gently) till it goes to where you removed it from, align the 2 studs up and install nuts , test window up and down before putting everthing back
Is the center bolt on the crankshaft damper pulley reverse threaded on a 1996 Chrysler LHS 3.5L?
No. Counter clockwise to loosen. It is very tight.
How can you disable the factory alarm on a 1994 Chrysler LHS?
It can not be disabled, it is reset with the remote or by unlocking the door with the key.
It can not be disabled, it is reset with the remote or by unlocking the door with the key.
How do you reset the Engine light on a 1996 LHS Chrysler?
un-hook the negative battery cable from the battery for 15 minutes and then re-attach cable.
What a motor that will replace 3.5 Chrysler LHS 1996 what car year will do this?
1996 or 1997 3.5 only
What other rims would fit your 1994 Chrysler lhs?
1993-1997 Dodge intrepid, Chrysler Concorde, or eagle vision
1994 Chrysler LHS died on the road and now does not want to start why?
how do you install a crankshaft sensor on a 94 Chrysler lhs....where is it located on a 94 Chrysler lhs???????????????????loisanne0@hotmail.com
Is a 1999 Chrysler lhs headlights interchangeable with a 1999 Concorde headlights?
yes but inside the housing, there is only a high n low beam, where as the lhs of 99 has projectors from the factory n has the turn signals inside the housing aswell, so that's up to ur imagination to make that work my friend, good luck
How do you replace the Third Brake Light In a 1994 Chrysler LHS?
Open the trunk & remove the trim that is below the rear window. The third brake lamp is a LED light which is one piece and several hundred dollars, unless you can locate one from a salvage yard. If a few of the bulbs appear to be out, put on gloves & pound on the lamp assembly with your knuckles to see if they will come back to life in which was the case on my 95 LHS before taking the trim off.
Where is the the PCV valve on a 99 LHS?
On the 3.5 engine, the valve is at the right back of the intake. On the 2.7 the valve is on the left front of the intake.
What size speakers fit 1999 Chrysler lhs?
2 6.5's in the front
2 6x9's in the rear
4 tweeters in the doors
3.5 in. in the front dash
Upstream is an O2 sensor located between the engine and the catalytic converter. Downstream is one located behind the converter.
Where is the Throttle Positioning Sensor located on a 2001 LHS Chrysler?
Behind the throttle body, it is a very tight spot, you need to remove all intake hoses leading to the throttle body which sits next to the firewall in the center of your engine.(towards the back if you are looking at if from the front of the car)
