Dodge Avenger

In a 2008 Dodge Avenger RT, the fog light switch is located on the headlight control knob, which is found on the left side of the steering wheel. To activate the fog lights, turn the headlight control knob to the "On" position, and then pull the knob outwards. If the fog lights are equipped, this action will turn them on.

The 2008 Dodge Avenger typically requires 5W-20 motor oil. It's important to use oil that meets the API certification for optimal performance and engine protection. Always check the owner's manual for any specific recommendations or requirements based on the engine type.

On a 2010 Dodge Avenger, the thermostat is located in the engine compartment, specifically near the engine block. It is typically situated in a housing connected to the upper radiator hose. To access it, you may need to remove the plastic engine cover and other components for better visibility. Always consult the vehicle’s service manual for precise instructions and safety precautions.

The ESP in the Dodge Avenger refers to the Electronic Stability Program, a safety feature designed to enhance vehicle stability by detecting and reducing loss of traction. It uses sensors to monitor the vehicle's direction and adjusts engine power and applies brakes to individual wheels as necessary to help maintain control during slippery conditions or abrupt maneuvers. This system aims to prevent skidding and improve overall handling, increasing driver confidence and safety on the road.

For a 2008 Dodge Avenger, it's recommended to use 5W-20 motor oil for optimal performance. You can choose between conventional, synthetic blend, or full synthetic oil, depending on your preference and driving conditions. Always check your owner's manual for specific requirements and recommendations.

To replace the idler pulley on a 2008 Dodge Avenger with a 2.4L engine, first, disconnect the negative battery terminal for safety. Then, remove the serpentine belt by using a ratchet or a serpentine belt tool to relieve tension on the tensioner pulley. Next, unbolt the idler pulley from its mount using the appropriate socket size, and replace it with the new pulley. Finally, reattach the serpentine belt, ensuring it is properly routed, and reconnect the battery.

On a 2007 Chevy Silverado Classic, grease fittings, also known as zerk fittings, are typically located on the steering components, such as the tie rod ends and ball joints, as well as on the u-joints of the driveshaft. You may also find them on the suspension components, like the control arms and sway bar links. It's important to check your specific vehicle's service manual for precise locations and maintenance guidelines.

The throttle position sensor (TPS) on a 2008 Dodge Avenger is located on the throttle body, which is typically found near the intake manifold. It monitors the position of the throttle plate and sends this information to the engine control unit (ECU). To access it, you may need to remove the air intake duct that connects to the throttle body.

The cost to replace valve seals on a 2008 Dodge Avenger typically ranges from $800 to $1,500, depending on labor rates and whether additional repairs are needed. This estimate includes parts and labor, with the majority of the cost attributed to labor since accessing the valve seals requires significant engine disassembly. It's advisable to get quotes from multiple repair shops for a more accurate estimate.

In a 2008 Dodge Avenger, the transmission pressure sensor is typically located on or near the transmission valve body. It can often be found on the driver's side of the transmission, close to the oil pan. To access it, you may need to remove some components for better visibility and space. Always consult a repair manual or professional for precise guidance.

The 2008 Dodge Avenger typically requires about 5 quarts of oil when using a standard oil filter. If you're using a larger filter, it may need slightly more, around 5.5 quarts. Always check the owner's manual for the most accurate specifications for your specific engine type.

If it is the 6 cyl. which i have if you are looking at the intake manifold it is on the back side to the right. There are 2 vacume hoses going to it, you can remove this, which i did because i had to replace it, autozone sells the egr valve for 65.99...hopefully i helped email me if you have more questions

The speed sensor on a 2012 Dodge Avenger is typically located on the transmission. More specifically, it can be found on the top or side of the transmission case, often near the output shaft. To access it, you may need to remove some components or shields, depending on the engine configuration. Always consult your vehicle's service manual for precise locations and instructions.

Yes, you can use 10W-30 synthetic oil in a 2008 Dodge Avenger, as it is compatible with many vehicles that require this oil viscosity. However, it's important to consult the owner's manual for your specific engine type and any manufacturer recommendations regarding oil specifications. Using synthetic oil can provide better protection and performance, especially in extreme temperatures. Always ensure that the oil meets the necessary API or ILSAC standards for your engine.

One possible cause for a 1995 Dodge Avenger stalling when shifted into reverse could be a faulty idle air control valve. This component is responsible for regulating the engine's idle speed, so if it is malfunctioning, the engine could stall when the transmission is engaged in reverse. It is recommended to have the idle air control valve inspected and potentially replaced to address this issue.

Best way to diagnose is to scan for codes, but not having that I would guess the ignition module then the crank/cam sensor.

should b bolts in engine compartment and then 1 bolt on bottom of strut make sure to use spring compressors and u will probably need heat for lower bolt dont worry about the smoke there is a rubber bushing in there u get a new one with new strut

have an alternator, battery, and electrical check to find out what the problem is. battery may not be taking a charge, or the alternator is not putting out enough voltage.

Type your answer here... It either means your air pressure is low in tires or tire..or one of the sensors are bad

As nearly as I've been able to tell, you must either use the Smart Key or the keyfob to disable the alarm. Other than that, you can see if the dealer can disable it permanently.

The 2014 Dodge Avenger is 6 ft. 0.8 in. (72.8 in.)1 one-touch power windows wide.

Remove the inside door panel from your 1996 Dodge Avenger. Remove the door handle linkage. Remove the door handle retaining bolts. Reverse the process to install your new door handle.

Check out a good Public Library.

how fast do 200cc choppers go

how fast do 200cc choppers go

that all depends on the displacement, they usually average between 65 and 90 mph

When they come from the dealer with a 5 speed transmission, their top speed is 45-50mph. you can modify them by putting a taller tire on the rear. A 185 60 14 car tire will fit if you get a used one (there are no motorcycle tires on the US market that will fit a 14 inch by 7inch rim. You are just plain screwed there) dealers don't tell you that part. And they don't tell you that they can't even get replacement stock size tires for it and that the stock tires wear out in less than 1000 miles! You can also replace the front sprocket with one with more teeth. I can cruise now at 60-65mph. These are a piece of junk. Seriously, get a Honda rebel 250. You will be much better off. mine is less than a year old and worn out from driving it on the roads,. These dealers for the 200cc choppers are the scum of the earth. If you still want something cheap that looks cool, then check out kikker 5150 bikes. They have a much better parts supply. Or you can just buy my 200cc chopper if you want one that bad and mine has already been titled in North Carolina.

5w30