0
Dodge Intrepid
In this category you can ask questions about Dodge Intrepids. These questions can include where to find parts, how to get help, or how to do it yourself.
1,915 Questions
What fluid is correct for 1996 Dodge Intrepid?
Engine - 5w30
Trans - Mopar ATF+4
Brake - DOT 3
Coolant - green
Power steering - power steering fluid
AC - R134a
How do you change a starter in a 1996 Dodge Intrepid?
My Guess would be if you look underneath by the rear of the motor you should see a round object about 8 to 12 inches longand 4 to 6 inches in diamiter. if i am right all you need to do is take a wrench and take out the bolts!
More specificallyOn a 3.3l engine the starter is about mid-engine on the driver's side. Follow the positive battery cable down to help locate it.- Always start by disconnecting the negative battery cable. A memory saver that uses a 9-volt battery and plugs into the cigarette lighter is useful as it retains computer and radio information.
- You'll need to take the usual safety precautions about jacking up a vehicle, including using jack stands.
The starter is held in with three bolts. If I recall, they are 15mm heads. I was only able to use a socket on one of them, the other two required a wrench and more time. Small hands are helpful. Once the three bolts are out, you'll need to unbolt the battery cable and unplug the solenoid wire. When reinstalling, do not over-tighten the battery cable bolt or you can damage the new starter.
Where is the fuse box for a 1997 Dodge Intrepid?
YES YOUR FUSE BOX IS LOCATED WHEN YOU OPEN YOUR DRIVER SIDE DOOR ON THE SIDE DASHBORAD THE IS A SLOT LOOKING THING IF YOU LOOK AT THE SLOT IN SMALL LETTERS IT WILL SAY FUSE BOX STICK HAND IN SLOT AND PULL
Where is the computer module in a 95 dodge intrepid?
To the side of the battery & relay box area on the driver`s side. should be attatched to the fender.
How do you replace the front sway bar bushings on a 1995 Dodge Intrepid?
When the sway bar try's to do it's job without the bushings then it will come in contact with the body of the car and will be an confortable ride that could causes more problems in the future.
What would make a whining noise come from a 99 Dodge Intrepid it does this in park and in movement?
ur car sucks!!!!
Seals are a group of marine mammals. The niche for seals are the sea in cold waters. Seals are predators and eat anything from fish, mollusks, and crustaceans.
It is called a "knock Sensor" it is the one that advances or retards the engine timing as needed, usually is green in color but there could be other colors and it bolts to the side of the cylinder head in beetwen both heads thank you
The igniton coils are the items in the middle of the valve covers.
How much does it cost to replace rotors and pads on a 2003 Dodge Intrepid?
Try using www.repairpal.com, it give prices for parts and labor be year, make, model and even your zip code for most common repairs.
94 dodge Intrepid brake lights stay on when car not running?
If the brake lights stay on when the car is not running on most vehicles, including the 1994 Dodge Intrepid, there is probably a short somewhere in the wiring to the brake lights. The first place to investigate this problem would be the wires along the firewall that control the brake lights.
Also, check the brake light switch above the brake pedal.
Where is EGR valve on a 1998 Dodge Intrepid?
EGR VALVE SITS BEHIND THE ENGINE, BOLTED TO A Y PIPE WHICH IN TURN IS BOLTED TO THE BACK OF THE INTAKE PLENUM (ON THE TOP OF THE ENGINE)
Where are the TRANSMISSION input and output speed sensors on a 2002 Dodge Intrepid?
They are on the driver's side of the transmission, and require a 1 inch deepwell socket to remove, and you may need some extensions to reach it.
Where is cradle bushing located on a 94 Dodge Intrepid?
The frame for the LH series of cars has a "sub-frame" or cradle which carries the engine/transmission. This sub-frame is bolted to the main chassis of the car with four large "cradle bushings" to islolate vibrations and such. If you jack up the car a little bit, and look underneath, you will readily see the engine cradle. You will see the four round mounts, two at the front, and two towards the back, where the rear transmission mount is. Each bushing is each is about 3 inches in diameter. They kinda look like an inverted cone with a large bolt head in the middle, with rubber squishing out around the outside edge of them. JH
What causes vapor lock in Dodge Intrepid 94?
I haven't seen "vapor lock" since the carburetor days. Give us the symptoms you are experiencing. Maybe we can come up with something.
What does trouble code p0700 mean on a 2004 aveo?
Trouble code P0700 means:Transmission control system malfunction
How do you change speedometer cable in 95 Dodge Intrepid?
It does not have a cable. The speed signal comes from the trasnmission output speed sensor.
2001 2.7 intrepid rocker arm torque spec?
My 2001 2.7L Dodge Intrepid se has a rocker arm or lifter stuck and I'm hoping for a cheap fix by resetting all the nuts back to there original torque. If anyone knows the numbers please let me know, since 3 places tried to make me pay way to much money for a simple answer. Thank you, Chris.
Will the cam sensor effect the cruise control?
Yes it could, if it is setting codes it will affect the cruise.
What is the code p0500 on a dodge 1999 intrepid?
Vehicle speed sensor malfunction. Most likely you have a failed output speed sensor on the transmission.
Vehicle speed sensor malfunction. Most likely you have a failed output speed sensor on the transmission.
How do you jump start a 2004 Dodge Intrepid?
Once the hoods of both vehicles are opened (if using cables) the positive to positive of each vehicle's batteries should be connected first. The second step is connecting a cable to the negative (ground) if the good battery to a frame component of the car that will not start. Then the car should be started. Often it may take a few moments while some charging occurs.
How do you change the Blend Air Door Actuator on a 2000 Dodge Intrepid?
I am faced with the same problem. I have had no heat for 2 weeks now, and Ohio keeps getting colder. Pulled a diagram of what the 00 Intrepid hvac system looks like, but I think I pulled the wrong motor. The heat blend door actuator, from what my buddy at work told me, is at the bottom of the center console in the dash, and you have to pull the ENTIRE DASH out to change the blend door. I told him, all I want to do is find it and push it open manually, then use a wire hanger to make sure it doesn't shut again. He said, "cool, start pulling the dash out, cuz you're gonna have to do it no matter what." ALSO!!!! As a side note, I thought I might add...there is a little known door at the top, passenger side of the module, called the recirculation door. If this door is shut, you could be looking at a loss of heat as well, seeing as it recirculates the air from inside the vehicle. I'd go with the heat blend door to start though...Will keep you posted as I gut my ride tomorrow.
l8tr,
Tim
The crank gear should be in the 12: oclock position & the cam gear should be in the 6: oclock position facing each other this is top dead center on compression stroke.
Why does the instrument cluster on a 1993 Chrysler Intrepid shut off after working for 5 minutes?
The instrument cluster gets its power/signal from the Body Control Module. I believe it is located behind the carpet somewhere by the passenger foot area. Not saying this is bad, but it's definitely something to check into.
