0
Dodge Shadow
The Dodge Shadow series is a range of compact cars introduced by Chrysler Corporation in 1987. It was a replica of the Plymouth Sundance. The series was manufactured in Toluca, Mexico, and Sterling Heights, Michigan.
405 Questions
Where is the fuse for the fuel pump on a 1994 dodge shadow?
the fuse is in uder the dash by drivers left kneee cap
Why 1994 Dodge Shadow 2.2 engine keeps overheating?
if the radiator is clear & there are no obstructions in front of radiator then make sure belt is properly tensioned next watch to make sure electric fan is cycling as engine gets hot next would be head gasket if other two is good
Do 89 dodge shadows with a 2.2L engine have a carburetor on it?
no they dont they have a throtle body injection(TBI) no they dont they have a throtle body injection(TBI)
Where is the heater core in a 1989 Dodge Shadow 2.5 lt?
I have an 89 shadow es turbo. It is located to the right of your gas pedal behind the dash. More or less behind the radio and vent controls. You pretty much have to remove most of the dash to get to it. Sorry. Also, if you car has a/c the refrigerant needs to be evacuated first since the cooling coil is in the same 'box' as the heater core. I didn't want to tackle the job and to replace my heater core was about 600 bucks...... Good luck.
Ideas why a 92 Dodge Shadow would go through 4-5 Oxygen Sensors per year?
If it is a 4 cylinder it is likely that the fuel injector is bad. I had a burnt wire that melted on the engine. It caused the engine to burn way too rich. It showed the code for the O2 sensor because it changed the fuel mixture so rich. I replaced the O2 sensor but that only lasted for a couple of months. I found out that it was the burnt wire that caused the engine to burn rich and giving bogus readings to the computer through the O2 sensor.
try changing your ignition modual drive safe
Why might the front power windows of a 1991 Dodge Shadow not work?
if both don't work I would check for a fuse or bad connection in a wiring harness. If one doesnt work i would check for a bad motor or bad switch
Just fixed my driver side power window. Is seams over the years, rust collected between the motor drive gear and the main gear that helps move the window up and down. I ended up taking the motor out and cleaning out the rust. Workes fine now. I had to take the time and remove the armrest and door panel to get inside the door itself to access the motor. Its not hard, just takes time.
Where is the fuel pump relay on a 1993 Dodge Shadow?
it is front of the master break cylnder on the drivers side the liitle black box that has the fuses has 4 plugins on the front of it sitting parell with the fuse box and the second plug is the relay to the best of my knoweldge, i had called oreilly autoparts and they looked it up on the computer , i do know that it was one of the four plugs for positive , i havent wnet bac an messed with mine as its been so cold and wet.
Why wont the Brake lights work on 93 dodge shadow?
Have you checked the switch on the end of the brake rod, I have had mine stuck, and even came loose and out of place a few times over the years. it has a bezel ring that gest loose, and the switch is spring loaded. So look way up the pedal rod, up toward the top.
How do you replace the thermostat on a 1992 dodge shadow 2.5?
there is a big hose going from the top of your radiator, to the engine block. where the hose meets the block, there is a metal fitting sttatched with 2 bolts. remove the bolts and you will see your thermostat sticking out. pull the old thermostat out, scrape the gaskets off and replace the unit, and the gaskets, and put it all back together.
Where the fuse for wiper for 91 dodge shadow?
It is up under the drivers side dash, a little left of the steering wheel ,it's better to lay down and look up, but the plastic moulding below the steering wheel pops off lmaybe 2 screws but it does come off and there you will find the fuses.
There is a auto shut down relay on the right fender that controls the fuel pump. It is the first relay from the front on the drivers side fender
How do you tell if your 95 Mercury Mystique has abs?
ABS came as standard equipment on the 95. It has ABS.
The timing specs for a 1994 dodge shadow 2.5 liter?
you can also put your heater on defrost and this will also operate the fan. sorry this answer was for another question.
Why won't the Gm envoy recirculate on climate control stay on?
it won't stay on if your blowing it the floor or using defroster.
Where is the fuel relay switch located on a 94 dodge shadow?
front driver side under the hood , over the wheel, well right in front of battery there are four square black boxes in a row that are about 2inches square and in most cases it the second from the front.email me at james_henderson@comcast.net and ill send you a picture from my car if you would like.
Were is the turn singles relay on a 1993 dodge shadow?
Look under the dash on the drivers side, you shouldn't have to remove anything. The relay is a silverish cylinder. It pulls right out from its mount.
Where is the fuel pump relay located on a 1991 dodge shadow?
It should be on the driver side fender... 2nd relay back.
How do you remove the ignition lock cylinder in a dodge shadow?
First off, you can visit Auto Zone and they have a pretty detailed procedure for this removal and replacement. 1993 Dodge Shadow, 5 speed http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c1528018e2c7 This was my experience, disconnect the negative power cable from the battery. You will need both # 20 TORX head driver. These are inexpensive from your auto parts store. # Remove the key lock cylinder from the ignition switch, as follows: # Insert the ignition key into the switch, then turn the switch to the LOCK position. Using a suitable small head Phillips head screwdriver, depress the key cylinder retaining pin until it is flush with the key cylinder surface. the cylinder retaining pin can be found on the left side of the key switch, look closely--it was my biggest challenge to find it. Rotate the key clockwise to the OFF position to unseat the key cylinder from the ignition switch assembly. The cylinder bezel should be about 1/8 in. (3mm) above the ignition switch halo light ring. Do not attempt to remove the key cylinder yet. # With the key cylinder in the unseated position, rotate the key counterclockwise to the LOCK position and remove the key. # Remove the key cylinder from the ignition switch. Installing the NEW # If the vehicle is equipped with a floor mounted gear shifter, place the selector in the PARK position. # Attach the wiring connectors to the ignition switch. Make sure that the switch locking tabs are fully seated in the wiring connectors. # Mount the ignition switch to the column: ## Position the shifter in PARK position. The park lock dowel pin on the ignition switch assembly must engage with the column park lock slider linkage. ## Verify that the ignition switch is in the LOCKposition; the flag should be parallel to the ignition switch terminals. Apply a small amount of grease to the flag and pin. ## Position the park lock link to mid-travel. ## Align the locating pin hole and its pin, position the ignition switch against the lock housing face and make sure the pin is inserted into the park lock link contour slot. Tighten the retaining screws to 17 inch lbs. (2 Nm). # With the key cylinder and ignition switch in the LOCKposition, key not in cylinder, gently insert the key cylinder into the ignition switch until it bottoms. # Insert the key. Simultaneously, push in on the cylinder and rotate the key to the RUN position. This action should fully seat the cylinder in the ignition switch. # Install the column covers and the tilt lever, if equipped. # Connect the negative battery cable and check the push-to-lock and park lock functions, halo lighting and all ignition switch positions for proper operation.
