Ford Laser

for starters you remove bolts from strut and wheel hub. then in the middle of the wheel hub you will see a bolt remove it.

pull tension on the c.v and axle and pop it out of the gearbox with a flat head screw driver. pull out. then remove c.v of axle and replace.

My 87 is 1mm. So around .8 to 1mm should be OK

Right underneath the car. You cant see it from the top, u will have to jack the car up to be able to see it. Be careful when changing it, don't burn yourself on the exhaust.

I don't think they have fuel pump shut off switch. What model?

remove handbrake handle console, there is the cable with the nut at rear of handle. put down handle and screw down nut 'till the handle comes up 7 clicks.

grab the turn signal lever and pull it toward you

Remove the inner door lining and reach up and push the clip up.

Cam belt or timing belt on Ford Laser Liata needs to be changed every 100 000 kms. It is made of rubber with geared teeth on the inner surface.

The safest way to get it right is remove the bottom pulley and line up the pointer on the crankshaft cog with the cut out on the back cover The cam gear has two marks that are put in the 3 o'clock position . The one at 12 o'clock lines up with the center of the cam cover.

When the belt is on, install the tensioner with the spring attached. Only let the spring tension be on the belt when you tighten the bolt on the tensioner. Turn the motor over twice by hand (plugs out) and check that the marks line up.

What is the question?

The water pump on the 92 Laser is easily replaced. You just need to untension the the belt driving the bump. Once you have done that all you need to do is undo the bolts and take the pump into your local auto parts dealer. Now that you have the pump install it and retension the belt.

Just did one last week, on my car. U actually have to remove alternator belt and powersteering/a/c belts, then remove timing belt cover, remove timing belt adjuster, and slide timing belt off top pulley, making sure you mark it before removing it, so as to put it back in same position. Next, unbolt 2 bolts at bottom of water pump (this is a bit fiddly, but doable, then, undo water pump, replace with new water pump, being sure to use gasket cement, aswell as new gasket, which should be supplied with pump, then put it all back together, in reverse order of removal. Fill cooling system, check for leraks, and voila, u have done it :)

On a Ford Laser, the oil filter is typically located on the underside of the engine, near the oil pan. It's often positioned towards the front or side of the engine block, making it accessible from under the vehicle. Depending on the specific model year and engine type, you may need to raise the car for better access. Always refer to the vehicle's service manual for precise location details.

The stud pattern for a 1988 Ford Laser is 4 bolts with a spacing of 4 inches (or 100 mm). The bolt size is typically M12x1.5. When replacing wheels, it's important to ensure the offset and diameter are compatible with the vehicle specifications for proper fitment and safety.

To set the timing on a 1990 Ford Laser, first ensure the engine is at operating temperature and then turn off the ignition. Locate the timing marks on the crankshaft pulley and the timing cover, and use a timing light connected to the number one spark plug wire. Start the engine and point the timing light at the marks; adjust the distributor until the timing mark aligns with the specified degree on the timing scale, typically around 10-14 degrees BTDC for this model. Finally, recheck the timing after tightening the distributor to ensure it remains in place.

To change the transmission on a 1991 Ford Laser, first ensure the vehicle is securely lifted and supported. Disconnect the battery, then drain the transmission fluid and remove any components obstructing access, such as the exhaust or driveshaft. Unbolt the transmission from the engine and support it with a jack, then carefully remove it from the vehicle. Install the new transmission by reversing the removal steps, ensuring all connections and fluid levels are correct before testing the vehicle.

For a 1992 Ford Laser, it is generally recommended to use 10W-30 or 15W-40 engine oil, depending on the climate and driving conditions. Always refer to the owner's manual for specific recommendations, as it may vary based on the engine type and local conditions. Ensure the oil meets the appropriate API (American Petroleum Institute) classification for optimal performance.

You can find a workshop or service manual for a 2001 Ford Laser Lxi KQ through several sources. Online platforms like eBay or Amazon often have physical or digital copies available for purchase. Additionally, websites like Haynes or Chilton may offer manuals for download or order. Local libraries or automotive forums can also be useful resources for obtaining specific manuals or advice from other owners.

On a 1995 Ford Laser, the horn is typically located near the front of the vehicle, often behind the front grille or near the radiator. It's mounted on the driver's side, usually attached to a bracket. To access it, you may need to remove the grille or other components depending on the specific model and configuration. Always consult the vehicle's service manual for precise location and access instructions.

The firing order for a 1994 Ford Laser, which typically has a 1.6L or 1.8L engine, is 1-3-4-2. This means that the cylinders fire in the sequence of the first cylinder, followed by the third, fourth, and then the second cylinder. It's important to ensure that the ignition system is set correctly to maintain engine performance.