Ford Laser

The coolant drain plug on a 1994 Ford Laser KH is typically located at the bottom of the engine block. To access it, you may need to remove any underbody covers and ensure that the vehicle is securely lifted. The drain plug is usually a threaded bolt or plug that can be unscrewed to drain the coolant from the system. Always consult the vehicle's service manual for specific details related to your model.

The starter motor for a 1995 Ford Laser LXI is typically located on the lower side of the engine, near the transmission. It is mounted to the engine block, often towards the back of the engine compartment, making it accessible from underneath the vehicle. To reach it, you may need to remove some components or shields for better access. Always ensure the battery is disconnected before attempting any repairs.

For the 1999 Ford Laser Tracer, the torque setting for the cylinder head bolts is typically around 63-72 lb-ft (85-98 Nm), but it’s important to follow a specific tightening sequence for even pressure. For tappet clearance, the recommended setting is usually around 0.008 inches (0.20 mm) for both intake and exhaust valves when the engine is cold. Always refer to the vehicle's service manual for the most accurate specifications specific to your engine variant.

To install a car radio in a 1996 Ford Laser Liata, first, disconnect the negative battery terminal to ensure safety. Remove the existing radio by carefully prying off the trim panel and unscrewing the mounting screws. Connect the wiring harness adapter to the new radio, matching the colors, then secure the radio in place and reattach the trim panel. Finally, reconnect the negative battery terminal and test the new radio to ensure it works properly.

To adjust the tappets on a Ford Laser, first ensure the engine is cold and remove the valve cover. Rotate the engine to set the piston of the cylinder you're adjusting at top dead center (TDC) on the compression stroke. Use a feeler gauge to measure the gap between the tappet and the rocker arm; adjust the tappet by loosening the lock nut and turning the adjusting screw until the correct gap is achieved, then tighten the lock nut to secure the adjustment. Repeat this process for each cylinder as needed, following the manufacturer's specifications for clearance.

Dump the old oil, rip out the old filter and replace, fill with new oil......

it goes into the tube that pushes into the flange that bolts to the water pump

it goes into the tube that pushes into the flange that bolts to the water pump

have clutches checked. My 89 Ford Taurus had the same problem and the clutches that control the fans were shot

1mm

it is in the disturber under the cap

Hi there,Carbby diagram ford laser.... I have just replaced all the gaskets in my carbby (1993 laser 1.6) & the "exploded" view of the carbby is in the box of gaskets. If you want me to send to you a copy of this diagram,send me your e-mail address & I will forward onto you this diagram. gemcampbell@iprimus.com.au I hope this will help you. regards David Campbell Perth W.A.

Perhaps you should take your foot off the brake and see if that helps ;-)

you have to turn the idle screw down ?? ? ? ? ? ? ? ? ? ? there are 2 of them. one on the right and one on the left. the left one is general idle and the one on the right is for air-conditioning idle and high power output idle ( rev higher ) A vacuum line may have come off if it has started revving.

hai iam manu i haVE A ford laser gl 1992 model in 1990 model for laser engine is different from that of 1992 gl model its engine is quite new the engine is mazda b platform engine with 16 valves but the old engine has only 8 valves so that the performance figure is different compared to the old drivetrain has also been immproved simultaniously a lpt. they are different series engine no similarities

If you have a hatchback their are usually 3 anchor points and you can find them on the inside of the boot between the floor and where the latch is, just look for a small round plastic disc about the size of a 50c coin, you just pop it out. You can also visit racq or some anmbulance stations will install one for you.

No just the rocket cover

fuze box picture

it has a timing chain. IT HAS A BELT !!

Yes

Check to see if vehicle is getting spark