Industrial Engineering

You go to an engineering school or college and take a course in Engineering Drawing.

PT's are typically used for metering and relaying purposes to sample the power system voltage and phase angles. The primary is at line voltage, and the secondary is typically between 66 - 120 volts (depending on primary connection, Line to Line or Line to Neutral). So yes, PT's are step down transformers.

melting loss very in all castings from 2% to 50%.

If you melt aluminum pure ingots & cast within minimum holding loss is 2%. If you cast in small batches it will go up to 15%.

If you melt aluminum scrap & cast within minimum holding loss is 15%. If you cast in small batches it will go up to 30%

If you melt aluminum turnings & cast within minimum holding loss is 25%. If you cast in small batches it will go up to 50%

melting loss very in all castings from 2% to 50%.

If you melt copper ingots+zinc ingots & cast within minimum holding loss is 12%. If you cast in small batches it will go up to 35%.

If you melt copper turning+zinc &chips & cast within minimum holding loss is 25%. If you cast in small batches it will go up to 50%

Its metric pipe, can also be thread male or female, din 65 is real close to 2.5" standard

the role of a contractor in construction is to ensure that the structure is built as per drawings. Specifically as per Architectual drawing because it is this drawing which best represents the final structure to an owner. In the fulfillment of their role the contractor will liease with consultants, sub-trades and owners to achieve the common goal of work being completed on time and with in budget.

ARTZXC

the rubber seal is used to seal the car of from the outside so that you want hear any wind noise and you dont get wet when it rains from water leaking in

320 degrees F

http://www.copper.org/applications/plumbing/techcorner/pdf/saturated_steam_tables.pdf

to avoid unnecessary use of sewing machines, reduce manpower , use of folders and attachment to make garment easily with quality, make R & D , time study for bulk production.

Rama

50 sq.mm of aluminium

and 25 to 35 sq.mm of copper

answer deleted because it is a copy-paste from a website

Essentially it contains a screw (under the handle) driving a round rubber washer onto the incoming pipe. This blocks the supply, but also slowly destroys the washer after a few years. At this point the washer can be easily replaced.

Around your neck. If you need to know the smallest perimeter, then measure around the smallest part of your neck. If you need to know the largest perimeter, then measure around the largest part of your neck. If you need to know the average perimeter, then measure around the smallest part of your neck AND the largest part of your neck, add the numbers together, & then divide that result by 2.

Industrial training institute

Systems science began as an emergence of General Systems Research. The theoretical frameworks consisting of systems analysis, systems design, system dynamics began in the 1950s.

poda punda nangalae theriama dhan serch pannarom . idhula enga kitta enda ketkarina punda mavaingala

Make the returned echoes easier to distinguish from Noise, Make target tracking easier with conical scanning, and it have no effect of the range resolution

There is only one advantage of waffle pod slab construction - reduced cost. The waffle pod slab is no more than a slab of concrete placed on the ground, with polystyrene blocks in a grid pattern within. This results in a system consisting of a slab with a grid of stiffening and edge beams, giving the (reverse) effect of a 'waffle' if viewed from underneath.

If construction is to take place on reactive soil, consideration needs to be given to the future maintenance of the slab. There is some requirement to ensure consistency in the landscaping and general treatment of the areas surrounding the slab. Typically, having concrete on one side, for example a driveway, gardens on another side, perhaps gravel on a third side and a timber deck on the fourth side can result in different soil moisture conditions which in turn can lead to structural movement and failure. Of course it is difficult to regulate the area underneath the slab.

Builders often advise that consistent landscaping or even a concrete apron around the house is required to ensure reliable performance of the slab, unfortunately this advice is sometimes given when it is too late. Typically, category 1, 2 and sometimes category 3 cracks appear, and when the builder is advised he engages an engineer (usually the engineer who designed the slap) to give an opinion. Invariably, it seems to be the fault of the owner.

The problem is that houses commonly have concrete on one side (the driveway) and gardens or lawn on another side, so the question really is, is it acceptable that the slab and foundation material be so fragile? Usually, stable foundation material will be found at a reasonable depth - perhaps 600mm - 1200mm. Home builders should obtain a quote for the price difference between a waffle pod slab and a conventional slab & beam construction, keeping in mind the cost of rectification in a cracking building and the effect on resale value.

Builders should advise their clients accordingly and give them the option. At the moment, clients are not given the option, the display homes they are shown are not cracked, the brochures do not warn of the likelihood of cracking, they are not told of the onerous maintenance requirements, and it is not until it is too late that the issue arises.

In early America about 1809 by creator Eli Whitney.

Certainly not. Once you've been doing isometric drawings for a while, the right technique will become second nature without having to use arrows as your guide. Isometric dot paper is also useful for this.

Micro strip antenna has following advantages :

1) Low profile : conformal (most important)

2) Easy to fabricate

3) Can be used in array

4) Easy to feed

the most important use of micro strip is its conformity as it can be conformed to the air crafts, missiles, satellite. A stealth aircraft has about 50-70 micro-strip antennas. the most popular of conformal microstrip antennas are Cylindrical, conical as the are mounted on various parts of aircrafts, missiles etc. they have many use on armament department.

procrastinate .

Not at all. It is weaker

Mining done by family members or community which is not under government is called rat hole mining in India. This is mainly done by tribals of north-east India. This is named so because they dig holes similar to that of rat holes to mine.

Between 45 and 50 Degree Celsius, depending on your body and the ability for it to handle the steam. Breathing becomes harder and heart rate goes up!