0
Kia Rio
The Kia Rio series is a subcompact car manufactured from 2000 to the present. Two generations of this car have been produced – all are equipped with front-wheel drive, and inline-four diesel and gasoline engines.
919 Questions
How do you replace a 2001 Kia Rio oil pan?
1. Remove the drain plug and drain the oil from the pan. 2. Remove the bolts on the perimiter of the oil pan. 3. Remove the oil pand and its gasket. 4. Install new gasket. 5. Install new oil pan. 6. Install new (or use existing drain plug). 7. OPTIONAL: now is a good time to replace the oil filter. 8. Fill appropriately with oil.
Where is the transmission in a Kia Rio?
should be drivers side under the hood
answer
The base trims are connected to a 5-speed manual transmission, which was earlier traditional for all trims. However, the 2011 model is coupled to a 4-speed automatic transmission, which is the traditional transmission for the SX and LX trims.
How many gallons does the gas tank in the 2008 Kia Rio hold?
The gas tank on the 2008 Kia Rio holds 11.9 gal..
The 2008 Kia Rio is 13 ft. 10.9 in. (166.9 in.) long.
How do you fix cv joint for a Kia Rio?
Replace the entire "half-shaft" The new one will have a warranty. Unless you're a good mechanic this is best done by a pro. The brake and suspension must be disconnected. I bought mine on line and saved a bunch.
Starter locaction for 04 Kia Rio?
Behind the engine. There are two bolts in front and one bolt on the back
How do you replace a tail light bulb on a 2001 Hyundai Elantra?
I just replaced the tail light bulb on my 2003 Elantra, so it may be the same for a 2001 model.
Open the trunk and open the cloth/plastic access cover found behind the tail light assembly. It is wedged in using flaps on three of the sides, but the fourth side is riveted to the trunk liner, so leave it attached on that side. It's flexible enough to act as a hinge and allow the cover to swing open.
You should see the ends of three bolts sticking through the metal part of the trunk. Remove the nuts from the bolts with a 5/16" wrench or socket. There is also a rubber socket that holds a metal post from the assembly, but you do not need to do anything with it, the post just slides out of the socket when you remove the assembly.
Gently pull the assembly away from the car, it may stick a little at first, but don't pull too hard, because the assembly is still wired to the car for power and you don't want to yank the wires out. Locate the back of the dead bulb's socket, and turn the socket until you can pull it out of the assembly. Rotate the bulb to remove it from the socket, and rotate the new bulb back in. Now that you know how to take it apart, just reverse the steps to put the assembly back onto the car.
What type of fluid does a 2004 kia rio automatic take?
oil- depends on season. Winter-5w30,summer10w40.
transmission fluid- standard AT fluid
Is a 2001 Kia Rio a good car to own?
Well personnaly I have mine for 5 years now and its the worst piece of c*** I ever own.Making the ford tempo 1989 the best car ever.Cost me a motor and a transmission and right now im about to put the fire to it...never buy a kia 2001!I keep having problem with even if never accidented and regurly checked.
******************************************************************
NEVER BUY A KIA EVER! from my experience ( automechanic) they are the worst cars to own besides a geo tracker.... Plus be AMERICAN BUY AMERICAN CARS
How many quarts of transmission fluid does a Kia Rio take?
What year, more than 1 transmission has been used. A 2001 takes 6.2 US quarts of SK ATF SP-III and a 2006 takes 6.4 US quarts (same spec) There may be others...that's why the year is needed.
Good Luck
fram .puralator, u can get them at any autozone, oriellys, and advance auto parts, run as little as $2.99 on sale to $ 6.99.
What happens when the timing belt breaks on a 2004 Kia Rio?
Well, the 2004 Rio 1.6l engines are "interference" type engines. If your belt breaks as you are cranking the engine over to start it, you're probably going to be ok, but if you're driving down the road at 45mph like I was, you'll likely need a new engine due to the cylinder heads smashing into the open valves at the top of the cylinders. Yay.
Kia's all have a zero clearance motors. here is a very good example. your timing belt breaks your motor is garbage! your intake valves spark plugs and exhaust valves will all be embedded in your piston. Please read your manual and go by what it says, and I state it says change it at 60,000 miles. If you want to save your motor in your kia Rio, Spectra, Sedona, Sportage, Amanti, Rondo, etc CHANGE IT AT 60,000 MILES!!!
Change out a standard transmission to automatic in a Kia Rio 2003?
Why would want to do that ? Manual transmission own.
How do you reset airbag light Kia Rio?
Most OBD II, III, scanner can not reset the airbag light.. When comes to KIA Rio the
best way to reset "Airbag Light" take it to your delar, it will take the mechanic about
3 to 5 min. to do it. Normaly no charge... atleast to the customer-service oriented
dealers.
How do you replace the tail light bulbs on a 2005 mountaineer?
I have an 02, but it should work the same way. Unscrew the tail light cover from the outside, then pull it off.
How do you change a timing belt on a Kia Rio Cinco 1.5 ltr?
Removal for 1.6L engines :
REMOVAL 1. Disconnect negative battery cable.
2. Loosen power steering lock bolts and nuts accordingly and remove tension from power steering (P/S) and/or air conditioning(A/C) compressor drive belt.
3. Remove P/S and/or A/C drive belt.
4. Loosen generator mounting bolts and adjusting bolt.
5. Remove generator bolts.
6. Remove water pump pulley.
7. Remove crankshaft pulley.
8. Remove upper and lower timing belt covers.
9. Turn crankshaft so that timing mark ontiming belt pulley is aligned with timing mark on engine.
10. Check that "I" mark on intake camshaft pulley is aligned with mark on seal plate and "E" mark on exhaust camshaft pulley is aligned with mark on seal plate.
Do not move camshaft or crankshaft once timing marks have been correctly positioned.
11. Loosen tensioner pulley lock bolt.
12. Protect timing belt with a rag.
13. Remove tensioner pulley.
14. Remove timing belt.
Mark the direction of timing belt rotation (on the timing belt) for proper reinstallation.
INSTALLATION 1. Install tensioner pulley.
Replace tensioner spring whenever timing belt is replaced.
2. Pull tensioner pulley to its furthest point and tighten lock bolt.
3. Check that timing mark on timing belt pulley is aligned with timing mark on engine.
4. Check that "I" mark on intake camshaft pulley is aligned with mark on seal plate and "E" mark on exhaust camshaft pulley is aligned with mark on seal plate.
If existing timing belt is being reused install belt in proper rotation direction marked prior to removal.
5. Install timing belt onto timing belt pulley first, then idler pulley, exhaust camshaft pulley, intake camshaft pulley, and tensioner pulley in that order.
6. Check that there is no looseness in the belt between idler pulley and exhaust camshaft pulley or between intake and exhaust camshaft pulleys.
7. Loosen tensioner pulley lock bolt and allow tensioner spring to apply tension to timing belt.
Do not add additional tension.
8. Tighten tensioner pulley lock bolt to specified torque.
Tightening torque:28~38 lb-ft (38~51 N·m, 3.9~5.2 kg-m)
9. Rotate crankshaft two full revolutions (clockwise only) and align timing mark on timing belt pulley with timing mark on engine block.
10. Check that "I" mark on intake camshaft pulley and "E" mark on exhaust camshaft pulley are aligned with marks on seal plate.
11. If they are not aligned, remove timing belt and start process from tensioner&;nbsp;installation.
12. Measure timing belt deflection by applying moderate pressure midway between camshaft pulleys If deflection is not correct, repeat from tensioner installation.
Deflection pressure:22 Ib. (98 N, 10 kg)Deflection:0.39~0.50 in. (11~13 mm)
13. Install lower and upper timing belt covers in that order.
Tightening torque:5.8~8.0 Ib-ft (7.9~10.7 N·m, 0.8~1.1 kg-m)
14. Install timing belt guide plate and crankshaft pulley.
Tightening torque:9.0~12.6 lb-ft (12.3~17.2 N·m, 1.3~1.8 kg-m)
15. Install water pump pulley.
Tightening torque:9.0~12.6 lb-ft (12.3~17.2 N·m, 1.3~1.8 kg-m)
16. Install generator belt and adjust the tension.
Were is the crank shaft position sensor on a 2002 Kia rio?
where is the crank position sensor located on 2003 kia Rio 1.8
The 2005 Kia Rio is 5 ft. 6.1 in. (66.1 in.)12V front power outlet(s) wide.
Can the airflow be adjusted by the Mass air flow sensor or meter?
jhinde hndcy yvm
uchycjkfigbg[bh
hfrgff
yt
jhj
h
kh
ky
kfjvfhgfviivgkgb
Is this an interference motor2001 Kia Rio?
Yes it is. Be sure to change your timing belt at or around 60k, 120k, etc. There are a couple of instances where people have not timed the engine right after doing the change and destroying the engine so take your time and be careful.
The 2007 Kia Rio is 13 ft. 10.9 in. (166.9 in.) long.
Where is the thermostat in a 2002 Kia Rio cinco?
The thermostat in a 2002 Kia Rio Cinco is located in the engine compartment. It is installed on the cylinder head.
