Kia Rio

You can check this in the owners manual or you can look on the cap of the power steering reservoir if either of these don't tell you I would say it would be ok to use any fluid you would like to use

timinm belt seting sistom

hoeveel pk is deze motor

The gas tank on the 2002 Kia Rio holds 11.9 gal..

Open the tailgate. On the inside next to the tail light, there will be two plastic covers. Remove them. You will see a Phillips head screw deep in the hole. These hold the light in place. Be careful removing them because they can fall down inside the vehicle. Use a magnetic tip screwdriver if possible. The light will then pull out of the truck. Then remove the plastic light module from the tail light. All the bulbs are connected to this module. Installation is reverse of removal. Just be careful not to drop the screw in the body cavity.

The fuse and relay compartment is under the hood on the drivers side fender well. The cover has a diagram and lables of all the fuses and relays etched on the inside. Explain "main fuse"

See *Rear Combination Lights* on page 10-53 of your "Owner's Manual", under Section 10: Maintenance and Service - Replacing Bulbs.....

Trouble code P0304 means:Cylinder 4 misfire detected

The 2013 Kia Rio has received really good reviews and was placed 9th out of 40 in the Most Affordable Car category of US News. The average price of a Kia Rio is between $14,294 and $18,510.

how to set timing on a 2006 kia 1.6

Dexron Mercon 3

you need to remove the front calipers then remove two Phillips head countersunk screws that are in the middle of the wheel studs

Here it is.

it takes 3 and a half quarts

i assume you mean by "RPMs" ,ignition timing,sadly you cant,its controlled by the PCM(computer) if you want to adjust idle speed, again ,no the PCM controls that through a device called Idle air control (IAC) if it wont idle, you have to find out why,there are no adjustments on this or any other modern engine other than spark plug gap.

The 2011 Kia Rio has a 1.6 L base engine size.

Open the hood. Look toward the rear of the engine and on the drivers side. The dip stick has a round "handle" on it, I think the color is yellow. The transmission is connected to the engine on the drivers side. If you look down into the engine compartment you should see where the transmission is connected to the engine. When you check the fluid level the engine should be warmed up and running, place the shift lever in park. Remove the dip stick and wipe it clean....now, with the engine still running, put the dip stick into the tube and insert until it it will not go any further. Remove the dip stick and check that the fluid is between the low and high marks. Add fluid if necessary.. Do not drive it with the level low, this will ruin it.

I hope this helps

Rear combination light assembly contains three bulbs. Two bulbs are single-filament and are used in hazard/turn signal and backup light circuits. Third bulb is a dual filament bulb; one filament functions as brake light and other as tail light. A plastic bulb holder mounts three lamps and associated wiring. Bulb holder can be removed from inside vehicle for bulb replacement.

I have recently just bought a 2003 Kia Rio and i personally think that it is a wonderful car. The gas mileage is great. Especially with the price of gas going up. You can drive forever on a tank of gas and it dont cost much to fill up!

Begin by removing the air conditioning condenser belt. Remove the air conditioner hoses. Remove the air conditioner condenser retaining bolts. Reverse the process to install your new air conditioner condenser.

The 2014 Kia Rio has a 1.6 L base engine size.

Do not use the oil instructed below.... 10w-30 is fine for mild climates.

SAE 75W-90

You mean the egr valve? Rios have precise timing with lower compression no need for an egr vale.

Here is the 2005 instructions that may work with your 2006, not sure.

Using jumper wire, connect jumper across pins 12 and 16 of the diagnostics connector which for my vehicle is located beside the battery in the engine compartment. See connector diagram below. 12 and 16 marked with "x".

oo oo

xooooooo

ooooxooo

Turn on ignition to ON.

Push LOCK button on all remotes TWO times.

Turn off ignition

Test remotes - they should work.

Hope that helps

Depends on the shop, Labor guide says 5 hours which is very close. I just done one for $200. One of the easier trans to change.