0
Mazda 323
Sold in many countries as Familia AP, the Mazda 323 was a rear wheel drive (RWD) car manufactured in 1977-1986. Mazda offered station wagon and hatch back bodies for this model and 1.0 L PC, 1.3 L TC, and 1.4 L UC engine options as well.
617 Questions
Where is the relay for the fuel pump on a 1988 Mazda 323?
The question has been going around for years. Does the rapper "Soulja Slim" who died in 2003 have any children? Indeed he does, so far we only know about one of his children who's name is A'darryl the kid is 15 years old now he was only 9 when his father was murdered.
Why won't my Mazda 323 1993 hatchback start and doesn't make noise?
I have similar problem with my 1993 Mazda 323 and I'm told its a problem with the immobiliser. Seems that the alarm system is hard wired into the ignition and fuel systems of the car and one part of it has perished with age so the whole thing is kaput
Do you know where the sensor for the alarm is on your car, because I can't find it on mine!
Can I disconnect the timer for my Mazda 323 ignition light that stays on?
no. you have to take the whole light out
Where is the transmission located on a 1990 Mazda 323 and how do you change?
Regardless of whether it's a manual or autoamtic, the transaxle (transmission plus final drive) is located on the left side (as you look forward) of the engine. Unless you have the right tools including an engine hoist or transmission jack, jack stands, and floor jack, it's not a job you want to take on. I assume you are replacing the transaxle with a rebuld or new unit. Plan a whole weekend to do this job.
Disconnect the battery, speedometer cable, clutch cable, gear selectro linkage reverse/neutral switch wiring, jack up car, support on stands, remove road wheels, drop the lower control arm bolts, remove the half-shaft nuts, remove the half-shafts (make certain you have a drain pan under the transaxle); remove the starter motor, support the engine, remove the bolts holding the transaxle to the engine, support the transaxle with a floor jack, remove the four bolts that attach the cross-member to the body, pull the transaxle away from the engine and lower the transaxle/crossmember assembly on the floor jack. Dettach the crossmemebr from the transaxle.
When reassembling, make certain all componets, wiring etc are clean; if manual transaxle inspect clutch & flywheel replace if needed, re-surface flywheel if needed. Once reassembled, fill transaxle with new fluid per manufacturer's recommedation; retorque all bolts per shop manual.
Good luck
Malcolm
I'm not familiar or experienced with your vehicle, but I suspect that it is warning you that something is wrong with the engine cooling system, and the engine is overheating.
This is not good. As soon as possible have someone who knows what he/she is doing to check out your vehicle's engine cooling system!!!!!
The fact that the engine is missing indicates the the engine temperature is WAY too high, and to continue to run the engine will result in RUINING THE ENGINE!!!!!
When i checked it out in day light, it was actually two separate problems. 1. One spark plug lead had come loose on the distribitor causing the missing. 2. The Heat problem was a faulty sensor on the Catalytic converter on the exhaust.
Unplug the sensor and the light will go off if it is.
How do you tell if your 1997 1.6L Mazda Protege has ABS brakes?
ABS equipped vehicles have an indicator light to warn of trouble. The light should come on for a couple of seconds when you turn on the key. If the light were burnt out, you could look under the hood for an abs controller near the master cylinder, or wiring to the brakes for a speed sensor at each wheel.
White smoke from exhaust when first cranking motor?
White smoke from the exhaust is a symptom of coolant entering the combustion chamber. You either have a blown head gasket or cracked head or both. STOP driving the car until you can have it repaired.
How does the piston fit on B3?
The piston fits on B3 by aligning precisely with the cylinder bore, allowing for smooth movement and optimal compression within the engine. It is typically held in place by the piston pin, which connects it to the connecting rod. Proper clearance and lubrication are essential to prevent wear and ensure efficient operation. Additionally, the piston rings create a seal against the cylinder wall, maintaining compression and minimizing oil consumption.
Where is the fuel pump located on a 92 Mazda 323?
On a 1992 Mazda 323, the fuel pump is located inside the fuel tank. To access it, you typically need to remove the rear seats and the access panel or drop the fuel tank itself. It's important to ensure the fuel system is depressurized before attempting any work on the fuel pump. Always consult the vehicle's service manual for specific instructions and safety precautions.
Where is the fuse or horn relay for your Mazda Astina 323 1990 model?
In the 1990 Mazda Astina 323, the horn relay is typically located in the engine compartment's fuse box. To locate the fuse box, open the hood and look for a rectangular plastic cover near the battery. Inside, you should find the horn relay labeled accordingly. If you're having trouble, consult the owner's manual for specific diagrams and locations.
