0
Small Engines
Miscellaneous small engines refer to low-power internal combustion engines (operating on gasoline/petrol), or electric engines. These include chain saws, lawn mowers string trimmers, snow and leaf blowers, wood chippers, and go-karts.
1,382 Questions
How do you know when to stop greasing a bearing?
u know when you have greased a bearing when grease starts puffing out. as far as do you ever stop greasing a bearing not as long as the bearing is still in service
How much does 50cc engine weigh?
A 50cc engine typically weighs between 25 to 50 pounds (11 to 23 kilograms), depending on its design and materials used. Lightweight models, such as those found in small scooters or dirt bikes, may be on the lower end of this range, while more robust engines could weigh more. Factors such as additional components and accessories can also affect the overall weight.
What can it be used for 4X Nickel babbitt?
The product called 4X Nickel Babbitt is a lead-free alloy. It is used to resurface bearings made by Babbitt. One package costs around $18 to $20, but some websites offer a discount if you order in large quantities.
01 raptor turns over and over pops but doesnt run?
Sounds as if you may have either a compression or a timing problem. I would check these two areas first. Also, a new spark sometimes does wonders.
Your spark plugs keep burning out and the engine is losing power what is the cause?
There is not a lot of information to go on from the question as posted. When an engine is in proper operating condition, the spark plugs should not be "wearing out", on a regular basis. From the information at hand, I would suspect the wrong heat range plug is being used. Check to see what spark plug the engine manufacturer recommends for your engine.
How to isntall points and condenser on a Briggs and stratton engine 10hp model 243431 type 0123?
CLEAN AND ADJUST CONTACT POINTS
Remove cover. Clean points with a carborundum contact point stone. Then insert a hard finished card or pied, of paper and close and open points. The paper will absorb any dirt or filings on the points. Adjust breaker points as follows:
a. Rotate crankshaft until points open to widest gap.
b.. Loosen lock nit illustrated below until it is just snug.
c. Rotate breaker point screw to obtain .020" gap.
d. When gap is .020" tighten locknut.
e. Replace breaker box cover. Same for installation, just eliminate the cleaning. CLEAN AND ADJUST CONTACT POINTS
Remove cover. Clean points with a carborundum contact point stone. Then insert a hard finished card or pied, of paper and close and open points. The paper will absorb any dirt or filings on the points. Adjust breaker points as follows:
a. Rotate crankshaft until points open to widest gap.
b.. Loosen lock nit illustrated below until it is just snug.
c. Rotate breaker point screw to obtain .020" gap.
d. When gap is .020" tighten locknut.
e. Replace breaker box cover. Same for installation, just eliminate the cleaning.
How do you increase speed on 50cc scooter 4 stroke engine?
Take out the top speed restrictor plate. If you don't know how to do it contact a proffesional.
where are the restrictor plates located
Are trams better than trains for the environment?
Trams are not bad for the environment, though if there a lot of them then sometimes
they can cause damage. It would be best not to use trams.
What is the best engine to ues in a go kart?
it depends if you want speed or power, what cog and chain you have and how big they are (small on motor and big on axel gives you lots or acceleration and power where big on motor and small on axel will give you a very high top speed (if you can get it to move))
How fast will a 6.5hp engine go on a go-kart?
3hp with 150lbs. rider 25mph. 6hp 35mph with 150lbs rider 120lbs. gocart balloon tires hard geared right with centrifical clutch
What other filter can you use for an Onan 140-3116 air filter?
NAPA 9087
Go to Wixfilters website. (Wix filters)
Go to Fram website. (Fram filters)
Go to Pureoil website. (Purolator filters)
Each one has a cross-reference tool in their website.
Apparently, I'm not allowed to give you the fricken links, due to some totally assenine policies that this website has.
Kudos! ~AJ
How do you replace the main bearing on a 2510 kawasaki mule?
There is only one main bearing. It is on the flywheel side and is a plane bearing (not a ball or needle bearing). You have to remove the crankshaft, press the old bearing out and press the new one in. Once the new one is installed, it MUST be checked for proper oil clearance. If it's not correct (tight), it will lock and destroy the rest of the engine. There is only one main bearing. It is on the flywheel side and is a plane bearing (not a ball or needle bearing). You have to remove the crankshaft, press the old bearing out and press the new one in. Once the new one is installed, it MUST be checked for proper oil clearance. If it's not correct (tight), it will lock and destroy the rest of the engine.
How many trains are run by Indian railways daily?
Almost 20 million people travel by rail in India each day. The rail network is extensive. Sixty thousand kilometers of tracks link 7500 stations.
How many minutes should a blower be operated before starting a engine?
It is recommended that you use a blower at least 4 minutes before you ever start the engine, and especially after fueling. How long should the blower run after fueling? After fueling, be sure to run your blower for at least four to five minutes and make sure you cannot smell gas before starting your eninge
Can you please send to me Turbine parts and function of each part shortly?
What are the tools you need to buy for motor rewinding?
I want to purchase some tools for electrical motor rewinding work hence please give me list of tools available to u with price list.
E-MAil- davidph68@hotmail.com
What is knocking and anti knocking agents?
The most common agent is Methyl tert-butyl ether, also known as methyl tertiary butyl ether and MTBE; a chemical compound with molecular formula C5H12O. MTBE is a volatile, flammable and colorless liquid that is immiscible with water. MTBE has a minty odour vaguely reminiscent of diethyl ether, leading to unpleasant taste and odour in water. MTBE is a gasoline additive, used as an oxygenate and to raise the octane number, although its use has declined in the United States in response to environmental and health concerns. In the US it has been used in gasoline at low levels since 1979 to replace tetra-ethyl lead to help prevent engine knocking. Oxygen helps gasoline burn more completely, reducing tailpipe emissions from pre-1984 motor vehicles.
Other anti-knocking compounds are available as oxygenate additives for gasoline, for example ethanol and related ethers, e.g. tert-amyl methyl ether (TAME). Ethanol has been advertised as a safe alternative by the agricultural interest groups in the USA and Europe. Its lack of toxicity is not different from MTBE, but as a polar solvent, it drives off nonpolar hydrocarbons from the gasoline, a problem that MTBE does not cause.
What do all generators and motors have in common?
They all have a rotating commutator in the centre and a coil surrounding it.
How do you change sliders on a 97' ski doo formula?
loosen track, tip machine enough to remove screw on one side front of slider, use a screwdriver/hammer to move the slider towards the back of the machine and through a track cog hole, may have to slightly pry it through to start, keep moving it back until out, measure old to new after removal, cut new to same size and tap through the same hole until screw hole lines up in front, put screw in. tip machine on other side and repeat. I took and used the small piece I cut to make slider the correct size as a sacrificial stiking device so as to not dammage the new slider. after second one is on, tighten track back up to spec and allign and good to go. Probably one hour from start to finish.
How do you check the compression of a small engine?
Box compression tester in Gujarat uses as a tool to check an engine's compression. It enables the user to gauge the engine's pressure output to make sure it is operating effectively. Compression testers are necessary for both detecting engine issues and optimizing engine configuration.
What is the altitude in Port Elgin ON?
Answered my own question. Looked up our local airport. Every airport site tells you the altitude of the area.
