Buick Regal

From battery to starter solenoid

It is located in front of the drivers side back tire in about a foot. It is cylyndrical and will take a lot of time if it hasn't been changed in a while. I would recommend using a lithium grease or rust remover if that's the case. I believe that one is located under the trunk area near the gas tank.

17.5 gallons

yeS BUT it needs to be replaced so it cant go

on the gm metric body 3 bolts hold the throttle pedal asm to the floor pan move the carpet to expose the bolts at the top of the throttle arm is the cable align the plastic bushing slot with the slot in throttle arm to remove the cable remove the bolts holding the throttle asm to the floor pan after removal u will see either a clip or sometimes a nub on the arm pivot remove clip or grind nub to remove pedal if u have to grind the nub u will have to secure the pedal from sliding its possible for the pedal to bind and this may cause the throttle to stick and that can be dangerous be very carful when installing pedal and throttle asm not only can the pedal bind but the carpet can ball up under the brake pedal i suggest having a pro do the job it may cost u but its better than taking a chance

In the fuel tank. Need to drop it down and remove from the top.

Drain the radiator. Remove the water pump belt. Take the fan off and fan shroud if necessary. Unbolt the pump and remove it. Bolt on the new pump, and reverse the process to finish the installation.

The 2012 Buick Regal has a 6-speed shiftable automatic.

There should be several places where there are ground wires; this is general and for most cars. * The large battery ground will normally go to the engine block or a good grounding spot on the engine. Often there is a smaller ground connected with the larger ground that connects to the car body normally at the fender or firewall. * On the inside the car near or under the dash board will be several different grounds; the grounds can be behind the left and right kick panels (near were your feet sat on the floor), attached to the center console if equipped, attached to the lower dash board, to the steering column, and under the front or rear seats to name a few. * Grounds can be found also in the trunk around the tail lights and other spot especially where there is electronic. * Grounds are sometimes under the car near the gas tank at the frame

Open the front passenger door and remove the plastic cover on the right side of the dash.

Some years were interchangeable, some weren't

If your problem is the instrument lighting, such as the odometer not displaying mileage. Then you would want to refurbish your cluster. I refurbish 97-04 century clusters so I think I may be able to help you out. Contact me at ANCTechnologies at hotmail.com

It should be located near the oil filter witch is under the power stearing pump. On the passenger side at the back of the engine. If the pressure switch is broken, you sould see your oil light on and have a trouble code on your computer, if you have a pressure indicator in the dash, it would indicate way to high pressure.

If its a mount referred to as a "dog bone", then replaceing it is really simple. You will need a 13 and 15 MM deep well socket, and a 13 and 15 MM wrench. With the motor in nuetral, the wheels chocked, and the parking brake set, you can easily wrench off the 2 bolts that hold the mount on.

Check out this link. It includes pictures. I am certain your 2000 Regal will be very similar if not identical to the 2001. http://www.clubgp.com/cgi-asp/mods.asp?modid=141

IF it is like the 1994 3.8 v-6, it is located on the top of the motor behind the alternator, you have to remove the plastic 3800 cover that snaps on to get to it. It is under a black vented cap that looks weird and says PCV in small letters on it but it is all in black so you have to look close, you just turn it and the pcv valve is set in a spring underneath it.

look below heater hose

how much ac oil do i put in my ac copressor

Master cylinder, upper firewall, driver's side.

Take off the plastic holders for the net at the back of the trunk. This will allow the plastic trim to move away from back of trunk then with a wrench or socket remove nuts that are on the threaded bolts that the plastic net holders were on. This will allow the whole assembly to be removed from the back (exterior) of the car. Now just remove connector half turn bulb remove old bulb replace new bulg and reverse to assemble.

Remove the plastic cover over the switch at the clutch pedal. The CRX switch can be unscrewed and replaced by disconnecting the wires and twisting the switch out.

The Regal Crown Club offers services where they give people credit if they go to the movies. With the credit earned from Regal Crown Club, one may earn free popcorn, soft drinks, movies, and more.

There are 2:

The first is on the top of the thermostat housing. To find it, follow the upper radiator hose from the radiator to the thermostat housing. It will probably be buried underneath part of the air filter duct and throttle cables, but visible without moving anything. The bleeder screw is very small, and enters the top of another, slightly larger bolt.

The second is on top of the water pump. It will look just like the one on the thermostat. The location of the water pump varies slightly with the size of the engine, but is usually in the same general location, on the left side of the engine. It will be near the lower radiator hose. On most 3.1L engines, the lower radiator hose connects right to the water pump. This is usually true of 3.8L engines as well, but not always.

Good luck.

You cant, it is computer controlled.

If the drive belt needs replacing it could also send the engine out of sync. Stand on the passengers side of the engine next to the wheel. Look down below the alternator & 6" towards the front, U'll see the belt tensioner. It's the slanted 'bar' with a pulley on each end. The lower pulley on the tensioner has 2 marks about an inch apart where the 2 halves of that pulley bolt together. On the other half of the same pulley u'll see 1 mark. U may need a flash light & some papertowels to clean off the marks. The single mark HAS TO BE IN BETWEEN the 2 marks on the opposite side. If the single mark is alot more to either of the 2 marks opposite it u need a new drive belt. To change the drive belt, put a 3/8 ratchet head into the squared hole in the upper pulley from where the 'marks' are. Then push the ratch handle towards the windshield & u'll see the drivebelt loosen. You can put a pipe on the ratch handle to extend it & give more leverage. Then put the new drivebelt on the same way u took the old 1 off.

It is bolted to the side of the cylinder head closest to passenger compartment on driver's side.