0
Chrysler Concorde
Chrysler Concorde was a four-door, front wheel drive vehicle manufactured from 1993-2004 by Chrysler. The vehicle was designed with short overhangs and low slung windshield. Its wheels were effectively placed to the side of the vehicle to create a bigger passenger cabin than its competitors.
815 Questions
Where is the crankshaft position sensor on a 1997 Chrysler Concorde?
Passenger side of the bell housing, behind the engine.
check ecu, ignition, wiring harness, fuses, relays, and cam sensor
Where is the data link connector located on the 95 Concorde 3.5 engine?
It is a 6 pin (may be blue or black) rectangle under the dash on the driver side.
It is not OBD 2 so it is not the normal 16 pin connector.
It is a 6 pin (may be blue or black) rectangle under the dash on the driver side.
It is not OBD 2 so it is not the normal 16 pin connector.
How do you replace fuel pump in a 1999 Chrysler Concorde?
fuel pump is located in the fuel tank. Tank musgt be removed for access.
How much freon does it take for air conditon?
depends on the car ,vans take more since some have rear air too. but there should be a tag under the hood , but its not wise to charge yourself ,since u don't know why its not working. its either low from a leak or a component isn't working such as the clutch isn't engaing or a low pressure switch and so on....
Where is the coil wire on my 2000 Chrysler Concorde?
A Chrysler Concorde does not use a distributor, so there is no coil wire.
Where is the oil filter located on 1999 Chrysler Concorde?
2.7L it is on the passenger side of the oil pan. 3.2L it is on the driver side of engine block, in front of engine mount, behind power steering pump.
1992 buick park avenue drivers power seat not working where and what to look for?
See if you have power to motor Check fuses
Spray penetrating oil, such as WD-40, on the shafts coming out of each of three motors under the seat, right where the shaft exits the motor, trying to get the oil into the motor. Over time, dirt accumulates in this area, creating friction and the motor stops turning and the seat doesn't move. After several tries the motor will begin to turn again and the seat will once again move.
There is a two wire connector from the wiring harness to the control box under the seat. Check the orange and black wires at both sides of the connector to make sure they aren't broken. You can also check for power coming from the harness side.
How do you change the turn signal bulb on a 1993 Chrysler Concorde?
Open the engine hood so you can see the turn signal/parking light assembly and using a flat blade screwdriver and push the retaining blade, between the headlight lens and the parking light lens, sideways, to allow the turn signal/parking light housing to slide forward. It may take some coaxing, as dirt has probably built up on the two guide slides. There is also a rubber grommet that is holding a centering pin in the back. Keep working the housing back and forth, it will come out. Once the housing is out far enough, twist the bulb socket 90 degrees and pull out socket and bulb.
Don't let shops tell you they have to take out the entire headlight assembly, as they did me. I replaced the bulb at home in ten minutes.
Were is the amplifier at for a 1999 Chrysler Concorde lxi?
Where are the factory amplifiers located inside of a 1999 Chrysler concorde?
Where is the solenoid switch valve latched in LR position code P1776 and P0700 for 2004 Concorde?
behind the trans pan and valve body in the solonoid pack 1 pac for each gear .
How do you change water pump on 2001 Concorde 3.2?
Do u need to take the pulls off to change the water pump on a 2001 concordeLXI 3.2 motor
Why won't 1999 Chrysler Concorde start?
There are a wide variety of possibilities as to why a vehicle will not start. A bad starter, timing belt, battery or alternator all could be reasons for a car not starting.
Where is the thermostat located on 1996 Concorde lx?
The thermostat is located inside of the thermostat housing on the front of the engine. You can follow the top radiator hose to the thermostat housing.
How easy is it to replace a Chrysler Concorde radiator fan motor?
It's not a five-minute job. I just had to replace one on my 1999 Concorde. You must remove the upper tie bar to access the fan/shroud/radiator assembly, remove the fan module from the radiator, replace the fan motor, then re-assemble everything. I would estimate maybe 1.5 hours for someone experienced in medium-level difficulty repair jobs. If any of this scares you or you don't know what those terms mean, then have a pro do it.
How do you replace the battery on a 2003 Chrysler Concorde?
You have to take the front passenger tire off and a plate under the wheel well to get to the battery.
What does the body control module operate on a 1995 Chrysler Concorde?
Locks, wipers, lights, most interior functions, theft, parts of the hvac etc
Where is the oil drain plug on a 1998 Chrysler Concord with a 3.2L engine?
It is on the bottom of the oil pan.
How do you get a 1995 Chevrolet Lumina starter out?
I did this today on my '95 Lumina w/3.1. Raise the car. Make sure it's secure, as the starter bolts can be rather tight and you might need to torque pretty hard. I had mine on ramps. Drain the oil and remove the oil filter, after it has drained, remove the plastic oil filter guard which is directly under the filter, three small bolts here. Loosen and remove two of the three nuts on the solenoid: the small nut which holds the ground wire and then one of the two 13mm nuts - the one that attaches the power wires. There is no need to remove the other 13mm nut for the wire that connects the starter to the solenoid. Loosen and remove the plastic cover where the starter meets the flywheel, this is only one small bolt. This part just keeps the dust and dirt out of the flywheel. There are only two bolts that hold the starter to the engine block, both are located near the flywheen end of starter. They are 15mm bolts and go from the direction of the bottom of the car up. One is located and accessible in front of the lower cross member and the other is located behind it. The one in front is a straight shot and easily reached with a long extention on the rachet. Mine was very tight and required a pipe on the rachet to break it lose. The one on the rear is a little trickier but not too tough if you have a swivel elbow for the socket. After these bolts are removed, the starter will be loose and can slide out easily through the bottom in the opening where the oil filter was. Installation is pretty easy and just the reverse of removal. Good luck.
