0
Chrysler Concorde
Chrysler Concorde was a four-door, front wheel drive vehicle manufactured from 1993-2004 by Chrysler. The vehicle was designed with short overhangs and low slung windshield. Its wheels were effectively placed to the side of the vehicle to create a bigger passenger cabin than its competitors.
815 Questions
Where is the speed sensor on a 1994 Concord?
The speed sensor is located behind the front driverside wheel over the cv boot. The wire for it is supported on the strut.
Location of thermostat on a 1999 Chrysler Concorde?
I have a 1999 concord engine 3.2 and I was told it is on the lower radiator hose on the engine block side.
Where is the turn signal flasher located on a 1995 Chrysler Concorde?
the flasher that causes the turn signals to flash But where is the flasher located on this car?
What is the meaning of Trag off at rhe instruments panel in Chrysler Concorde 2000 car?
your car might be equipe with traction control. is there a button somewhere that says trac if you push does light goes out if so this shifts power from one tire to another when you loose traction on ice or loose gravel
How do you reset the radio in a 2000 Chrysler Concorde after changing the battery?
get code from dealer
How do you replace the alternator on a 98 Chrysler Concorde?
There are three main steps behind replacing the alternator on the 1998 Chrysler Concorde. The first is disconnecting the battery cables for safety. Second, is depressing the belt tensioner to allow for the release of the drive belt. Finally the alternator can be unbolted from its bracket for replacement. If the drive belt, idler pulley and tensioner are worn it would be an ideal time to replace this components as part of the install.
How do you remove the door panel on a 2000 Chrysler Concorde?
There are 3 screws at the bottom of the door panel, one behind the inside door handle lever and one under the small cover inside the recessed area used for closing the door. Then you need to pry out the mesh covering the speaker using a flat screw. There are 3 screws inside there as well. Once you have removed all the screws the panel should be loose at the bottom. Pull out and push upward to free the panel. Then you need to unlock the small lever connected to the inner door handle. Also unscrew the locking lever near the B pillar. Disconnect the electrical cable for the courtesy light and the panel is completely free. Reverese the process the fix it back.
superglue for the pastic liner
phillips driver
10mm socket + 6"ext
Does a 1996 Chrysler Concorde lxi have an electric fuel pump?
Yes. It is in the fuel tank, and is accessed through a plate under the carpet in the trunk.
What else could cause chrysler concorde to make a clicking sound when trying to start?
Weak battery, corroded or loose battery cables, failed starter.
How can you take off a Chrysler Concorde hood?
To remove the hood from a Chrysler Concorde, first, ensure the vehicle is parked on a level surface and the engine is cool. Open the hood and secure it with a prop rod if necessary. Next, disconnect the hood release cable if applicable and remove the bolts securing the hood to the hinges using a socket wrench. Finally, carefully lift the hood off the hinges and set it aside.
Where is the weep hole on a 2.7 liter water pump on a 2002 Concorde?
The weep hole is next to the thermostat housing, which is where the lower radiator hose hooks to the engine.
The weep hole is next to the thermostat housing, which is where the lower radiator hose hooks to the engine.
How much does a rebuilt 1998 3.2 liter chrysler concorde engine cost?
I just checked (11-19-13) Jasper engine and transmission and the engine lists for $3998.00 with out core charge.
I just checked (11-19-13) Jasper engine and transmission and the engine lists for $3998.00 with out core charge.
Where is the computer at on a 1996 Chrysler Concorde?
It's below air filter compartment (engine)
There are also transmission and ABS computers under the hood.
There are also body, airbag, HVAC, and cluster computers inside the car.
How do you fix code P0122 on a 1998 Chrysler Concorde?
Throttle Position Sensor/Switch A Circuit Low Input
You need to test the wiring to the TPS, check the computer, and maybe replace the tps
Where is the speed sensor located on a 1996 Chrysler Concorde?
The transmission speed sensors are located on the driver side of the transmission case. Those are also where the speedometer signal comes from. The abs sensors (if equipped) are located at each wheel bearing.
Why your 1995 Chrysler Concorde goes into a limp mode when it reaches a certain temperature?
The transmission computer default to limp mode when it detects a malfunction. It will also set a trouble code. You need to have the code read with a scan tool to know possible causes.
Where is the air conditioner clutch on a 2004 Chrysler Concorde?
On all cars, the air conditioner clutch is on the front of the air conditioner compressor. The clutch is a unit by itself, while it's mounted on the shaft which is part of the compressor.
A belt drives the clutch, and the clutch (when engaged) drives the compressor.
Clutches tend to be held on in odd ways, snap rings might be involved. Also a puller is usually needed. Don't head into this without checking the information for your specific car.
What is wrong if the speedometer stops and the engine keeps cutting off on a 1999 Chrysler Concorde?
Could be just about anything. I would check the fuel filter, if it never has been changed it could be dirty, and only allow a little gas to get through enough to run the engine then starve it for fuel. When was the last tome this vehicle was tuned up? it may just need a tune up. Have the plugs ever been changed? But from your description I think it's a fuel problem.
Replace center brake light Chrysler Concorde?
I have a "93 concorde, with the light in the back window... I have to open the trunk lid, and reach underneath the unit. There are two bulbs in mine, the housings both twist out with a 1/4 turn(they are keyed with large and small slots as are typical of bulb housings, so they must be oriented properly to be re-installed. these bulbs can be removed by pulling straight out, I believe they are a #921, but should be printed on the base of the glass part of the bulb....hope this helps.
