0
Chrysler Sebring
The Chrysler Sebring is a range of middle-sized cars manufactured by American carmaker Chrysler between 1995 and 2010. It is one of the few practically priced automobiles available in sedan and convertible body styles.
2,284 Questions
Where is the mass air flow sensor located on a 2005 Chrysler sebring?
It doesn't have a mass airflow sensor.
It doesn't have a mass airflow sensor.
How do you manually raise the power windows on Chrysler sebring?
How do you manually raise the power windows on chrysler sebring?
Where is the oil pressure sending unit on a 2002 Chrysler sebring?
Its between the motor and the firewall, just above the oil filter, hard to see at first because of the heat shield from the exhaust, going to need a 10mm socket to take the heat shield off
Where is the camshaft sensor located on a 2002 Chrysler sebring 2.7 liter engine?
i replaced mine on a 2001 sebring sedan lxi, when you face the front of the car, it is on the left side of your engine, down between the coolant reservoir and the engine side. there is a black plug that covered the bolt on mine. I had to get a 13mm "long shaft" lug to get it unscrewed. if it is a tight area for your hands, you may have to partially remove the coolant reservoir (have another bottle of coolant ready, in case you lose a lot from removing it.
How do you change the blower motor switch in 2001 Chrysler sebring?
The hvac switch is part of an assembly that has the on/off fan speed, temperature control, selector switches and rear window defroster all combined. To replace the blower switch will require replacement of the complete assembly since it is all made as one unit. To remove the switch, first remove the front wood grain panel around the radio and switch assemblies. It has six holders, three on each side of the panel. It is best to start at the bottom with a small flat pry bar and then work up toward the top of the cover. This cover is plastic and can easily break, so be gentle when prying it off. When you have the panel pulled out, remove the two cables from the back of the switch assembly and the whole thing should be free. The hvac switch assemby is held to the wood grain panel with six 4mm screws.
Is it hard to get to and replace the water pump on a 2001 Chrysler Sebring?
Not real hard but you need direction. Get a manual on your car from the parts store or from AUTOBOOKSONLINE.COM. It will cost about $20
How do you replace the alternator on a 1996 Chrysler Sebring JX convertible?
I just replaced the alternator on a 97 Sebring JXi convertible, 2.5L engine. I had to remove the four AC compressor mounting bolts so that the AC could be moved away from the engine enough to get a socket on the alternator pivot bolt. You do not need to break the compressor lines. I also removed the top mounting ear bolt and the bracket to make room to remove the alternator from the engine compartment. Of course the first thing you do is disconnect the negative battery terminal either at the battery or at the jumper cable location in the engine compartment. You also have to loosen the idler pulley and remove the belt. I removed the front right wheel and plastic cover to get to the pulley and belt. This also permits better access to the AC compressor bolts. I found it easier to get the alternator free before I disconnected the electrical wires.
How do you Change the battery in a Chrysler Sebring key fob?
Very carefully pry open the remote. I took mine to " Batteries Plus" and the guy was only to happy to open it and install the new battery. He had a little special gadget.
Do the back seats lay down in a 2005 Chrysler sebring convertible?
No. The seats are bolted solid in place.
Where is the convertible top motor in a 2004 Chrysler Sebring?
It is behind the rear seat.
It is behind the rear seat.
Where is the cabin air filter on a 2008 Chrysler Sebring?
The cabin air filter is located behind the glove box. If you remove the glove box door you will see a small access door in the HVAC housing.
How do you find the problem if your Chrysler Sebring's 20v ignition fuse keeps blowing out?
I had the same problem. Everytime I would turn the ignition past Accesory to the On position the 20A fuse would pop. I went through 15 or so fuses. I could get it to start every now and then, so one time it started I drove it up to Sears Auto and they diagnosed the Battery as having a bad cell. Replaced the battery and haven't pop a fuse since then.
Popping the 20A ignition fuse....have your battery tested and probably replaced!
check the starter too if battery is good
I had this problem as well. It turned out to be the starter. It occurs when you move to "start" and the starter fails to engage. Whether this was simply a bad solenoid, or something else in the starter, I can't say for sure. In short, if the engine didn't immediately turn, the fuse would blow in about 2 seconds. I got around it for quite a while by being very careful to not hold the switch in start unless I detected the engine turning over. Eventually the starter ws relaced and all is well.
that usually indicates a vacuum leak which causes the system to go into default mode, which is defrost.
Where is the fuse box under hood on a 2007 Chrysler Sebring?
It is the black rectangular part on the driver side.
What can cause a 2004 Sebring LX to hesitate after you put gas in a tank that was low?
Clogged fuel pump or air on fuel lines. Residue from the tank might clog the fuel intakes. Changing the fuel filter might help. But before spending for a fuel filter, try using a fuel injector cleaner for about $5. In my case, before the fuel injector cleaner, the car would take 2 or 3 turns of the ignition key to start. And it also cured a slight hesitation problem. 30,000 miles after first having this problem on my 1998 Sebring LX, 4 treatments have cured the problem 4 times.
It shuts down the voltage to the primary coil on the distributor, power to fuel injectors, and fuel pump also.
Can 20 inch rims fit on a 2004 Chrysler sebring sedan without getting it lifted?
yes, as long as you have a compatible bolt patter you will be fine, anything bigger than that you will need to get a lift to raise your car to get a right clearence.
How do you add transmission fluid to a 1996 Chrysler sebring?
pour down the same tube you check it with
Chrysler sebring starts then dies within seconds?
Computer chip is in key. It must not be programmed correctly.
What size are the freeze plugs on the 2000 Chrysler Sebring Convertible?
we have encountered multiple sizes; 25mm / 32mm / 41mm. the clevite part# for the 32 mm is 219-3173. we have ordered those through n.a.p.a. in the past. hope this helps someone. ralph, natick auto clinic, inc.
Does a 2004 Chrysler Sebring have fuel injection?
Yes, the last Chrysler product with a carburetor was 1987.
