Ford Thunderbird

goggle it

maybe you should try to install some strut bars on top of your engine to hold it in place.

It won't happen unless you buy an aftermarket high performance PCM like an El-Diablo or something. There is no separate "chip." The PCM is programmed the way it's programmed by the manufacturer, and that is the way it is. I guess you may be able to buy an aftermarket "programmer," but I have seen a whole buncha car engines totally messed up by that stuff, including the aforementioned high performance PCM's. These engines are simply not made to handle the stress of performance enhancers, that is why there is protection software installed into the PCM. But I realise that some folks just have money to burn on replacing engines.

Trouble code P0320 means:Ignition/distibutor engine speed input circuit malfunction

there are several answers to that question so thats kind of hard to answer with one answer I would try cleaning the throttle body, checking the map sensor,check the mass airflow , and also changing the fuel filter,I have done all of those and mine has settled down, it may also be as easy as adjusting the kickdown cable or the adjustment screw on the throttle body but I would check the fuel filter first and then going on to the rest do the cheapest first. most times its the simple things that get you.

18 gal.

if it is a 4.6 v8 you dont it is controled by the ecm

Either at the rear or side of the oil pan

302 cubic inches

You have to replace the entire light unit. The bulbs are not replaceable. Try a junkyard or Ebay for used units.

The ball joints on a 97 Ford Thunderbird are replaced by placing the vehicle on jack stands, removing front wheel and rotor, and unbolting the steering knuckle. A ball joint puller is then used to remove the ball joint and a special installer tool is used to press the new one into place.

Hey Michael==It would help if you listed what kind of car yu have. SOME cars you can get into the trunk by taking the back seat out and with long extensions, remove the latch. Good luckJoe

On a 1992 Ford Thunderbird, the crankshaft position sensor is typically located near the crankshaft pulley at the bottom of the engine, often on the driver's side. It may be mounted to the engine block or transmission bell housing, depending on the specific engine configuration. To access it, you may need to remove some components or get under the vehicle for better visibility. Always consult a repair manual for your specific model for detailed instructions.

To recharge the air conditioning on a 1992 Ford Thunderbird, first ensure you have the correct type of refrigerant, which is R-134a for this model. Locate the low-pressure service port, typically found on the larger of the two lines connecting the AC compressor. Connect the recharge kit to the port, start the engine, and turn the AC to the maximum setting. Follow the instructions on the recharge kit to add refrigerant until the system reaches the recommended pressure. Always wear safety goggles and gloves while handling refrigerants.

To remove the backseat in a 2003 Chevrolet Impala, first, locate the seat release tabs or bolts at the base of the seat. Typically, you need to pull up on the seat bottom to release it from the clips holding it in place. For the seatback, there may be bolts or clips at the top or bottom that need to be unscrewed or disengaged. Once released, carefully lift the seatback out of the car.

The purge valve on a 1996 Ford Thunderbird is typically located on or near the engine, specifically along the intake manifold or near the throttle body. It is part of the evaporative emissions control system, and you can usually find it connected to the charcoal canister and the intake vacuum source. For precise identification, it's advisable to refer to the vehicle's service manual or a repair guide.

To change the 3rd brake light on a 1995 Ford Thunderbird, first, open the trunk and locate the access panel or cover behind the brake light assembly. Remove any screws or clips holding the panel in place. Disconnect the wiring harness from the old light bulb, twist the bulb socket counterclockwise to remove it, and then replace the bulb with a new one. Reassemble everything by reversing the steps, ensuring the bulb is securely in place before closing the access panel.

To disable the alarm on a 1997 Ford Thunderbird, insert the key into the driver's side door lock and turn it to the unlock position. This action should deactivate the alarm system. If the alarm persists, you may need to disconnect the car battery for a few minutes to reset the system. Always refer to the owner’s manual for specific instructions related to your vehicle model.

The fan sensor on a 1997 Ford Thunderbird is typically located near the engine's cooling system, specifically on or near the engine coolant temperature sensor. It is usually situated on the engine block or cylinder head, often towards the rear of the engine. To access it, you may need to remove some components for better visibility. Always refer to a repair manual for detailed instructions specific to your vehicle.

The front wheel bearing torque specifications for a 1995 Ford Thunderbird typically require the hub nut to be torqued to approximately 250 ft-lbs (340 Nm). It's important to ensure that the bearings are properly seated before applying this torque. Always refer to the vehicle's service manual for the most accurate and specific torque settings, as variations may exist based on the specific model or options.