0
Infiniti Q45
Manufactured in Japan from 1990 to 2006, Infiniti Q45 is a four-door rear-wheel drive powered by a V8 engine. Originally intended for upper-middle class families, it was sold to Nissan because of its unimpressive sales performance.
285 Questions
Why does your 1993 infinti q45 stall then cut itself completely off once you stop?
From my experience, it could be your MAF (Mass Air Flow) sensor. Signs and symptoms of a bad MAF are stumbling, rough idle, occasional stalling , etc. It could be that your connector is corroded, the pins have come uncrimped, or the unit itself needs to be cleaned or replaced. Another culprit of stalling in early Q45's could be low ATF.
Why does the slip light come on in a 1994 Infiniti Q45?
Well, I am not a mechanic but I own a 96 Q45 and experienced a similar problem. The warning light has to do with the traction control system. Your problem could be a number of things since the Q45 has so many sensors and relays etc. When I went to my dealership with my problem, the service advisor pointed out a black plastic box under the hood on the passenger's side close to the firewall. The black plastic box is attached to a silver aluminum box with a number of hydraulic lines attached to it. Remove the cover from the plastic box and you will see two relays inside. On the advice of the service advisor as a first step to solve the problem I replaced the two relays. That did solve my problem and that was almost 4 yrs ago now. The relays pull right out of their sockets and you just plop the new ones in. I live in Fl. but ordered my new relays from Infiniti of Scottsdale Az. because I could get them much cheaper there. They are called "Relay Assy-valve" Part# 47605-17V03 ($20.27) and "Relay Assy-Actuator" Part# 47605-17V10 ($19.28).
Hope this helps
What is the shop labor hours to replace a knock sensor on a infiniti q45 1997?
"http://wiki.answers.com/Q/What_is_the_shop_labor_hours_to_replace_a_knock_sensor_on_a_infiniti_q45_1997"
I have bad vibration in rear from 30 mph and up in a 92 infiniti Q45 any ideas?
The driveshaft on the 90-93 Q45 had a thinner rubber bearing than the ones found on the later model years. According to my Q45 specialist, it was a common issue and was usually replaced under warranty. If your Q45 has 100k+ miles on it, I would suspect the driveshaft bearing. Purchasing a factory driveshaft now would most likely get you the later model shaft with the thicker bearing. Another issue could be your transmission mounts and exhaust hangers. The rubber may have deteriorated and severly hampered it's ability to dampen the vibrations.
Full instructions are at http://www.handa-accessories.com/element/05fogs.pdf includes wiring info. Helpful even if you are not installing their kit.
How do you fix code 1320 on a 1997 infinite Q 45?
on my 1997 infinite Q45 i have the code 1320 how do i fix it?
What are quantitative techniques?
Many of the quantitative techniques fall into two broad categories: # Interval estimation # Hypothesis tests Interval Estimates It is common in statistics to estimate a parameter from a sample of data. The value of the parameter using all of the possible data, not just the sample data, is called the population parameter or true value of the parameter. An estimate of the true parameter value is made using the sample data. This is called a point estimate or a sample estimate. For example, the most commonly used measure of location is the mean. The population, or true, mean is the sum of all the members of the given population divided by the number of members in the population. As it is typically impractical to measure every member of the population, a random sample is drawn from the population. The sample mean is calculated by summing the values in the sample and dividing by the number of values in the sample. This sample mean is then used as the point estimate of the population mean. Interval estimates expand on point estimates by incorporating the uncertainty of the point estimate. In the example for the mean above, different samples from the same population will generate different values for the sample mean. An interval estimate quantifies this uncertainty in the sample estimate by computing lower and upper values of an interval which will, with a given level of confidence (i.e., probability), contain the population parameter. Hypothesis Tests Hypothesis tests also address the uncertainty of the sample estimate. However, instead of providing an interval, a hypothesis test attempts to refute a specific claim about a population parameter based on the sample data. For example, the hypothesis might be one of the following: * the population mean is equal to 10 * the population standard deviation is equal to 5 * the means from two populations are equal * the standard deviations from 5 populations are equal To reject a hypothesis is to conclude that it is false. However, to accept a hypothesis does not mean that it is true, only that we do not have evidence to believe otherwise. Thus hypothesis tests are usually stated in terms of both a condition that is doubted (null hypothesis) and a condition that is believed (alternative hypothesis). Website--http://www.itl.nist.gov/div898/handbook/eda/section3/eda35.htm
P.s "Just giving info on what you don't know" - ;) Sillypinkjade
----
How to replace fuel injector for 1992 infiniti q45?
Injectors 1, 2, 4, & 8 (the four corners) are able to be removed without taking off the plenum. Detailed instructions with pictures can be found @ Q45.org.
How many quarts of oil does a 1999 Q45 infiniti use?
A 1999 Q45 takes 6 quarts of oil (with a new filter).
What does the code p0420 mean on a 2002 infinity Q45?
Trouble code P0420 means:Catalyst system efficiency below threshold
There are many types of ballasts in the electrical industry. To get an answe, the type of ballast must be stated.
Where is the starter on 1992 infinity q45?
under the passenger side of the car you will need to remove the tire and lift the car up high to see it
Well there should not be a sleve in the crank snout where the seal lip rides. If there is one, then the crank has been reconnditioned/replaced, or there was damage to the snout, previously. I will recommend leaving the sleave, or replacing it with a new one if it has obtained rotational damage from the seal lip. This happens usually due to oil starvation at the lip ridding area or from a hardenned seal. The sleves may be purchased at your local autoparts and only serve to go over the damaged grove that the seal duged in. If the seal was not leaking and one is replacing the seal as maintenance or timing chain r&r. then leave the sleave in place other that that remove damaged sleve and replace with new one..Hope this helps.. Will..:)
Why would the slip and TRAC light come on on a 1998 infinity Q45?
I am far from being an expert or quasi expert but I do own a 96 Q45 and experienced a similar problem. I was helped or given advice free of charge by my local Infiniti Service Adviser. The problem had to do with the anti-lock braking system and its electrical components. There are two fairly inexpensive relays under the hood that you should try replacing first. My cost for both relays was $48.50 from Infiniti of Scottsdale, Az. (1-800-955-9181). The relays are called the ABS relay assy-valve and the relay assy-actuator. I live in Florida but I order most parts I need from Scottsdale because they are usually much cheaper. The mechanism of concern should be located under the hood at the right rear corner near the fire wall. You should see a little black plastic box mounted to the rear of a silver aluminum mechanism with a number of small metal tubes coming out of it. But you are only concerned with the black plastic box. Remove the cover and you will see the two relays I am talking about. The relays pull right out by pulling up on them. This is what I replaced and solved my problem. Calvin Bryant
How do you reset SRS air bag light on Infiniti Q45 1996?
If your airbag light on your 90-96 Q45 or similar year Infiniti vehicle is blinking, chances are it has been inadvertantly been set into self diagnosis mode. It does not indicate a problem with the airbag system. Unplugging the battery will NOT clear the self diagnosis status. To do this procedure, turn the vehicle on (engine not started) with the drivers side door open. Within 10 seconds of doing that, press the drivers side door switch more than 10 times within those 10 seconds. If you did the procedure correctly, the airbag light should go off. If it does not go off, it means there is a fault with the airbag system.
Where are Infinity Cars Manufactured?
When I bought my 1st QX56 the Infinity dealer told me the assembly plant is in Mississippi. The website below http://www.nissanusa.com/about/corporate-info/nissan-in-north-america.html lists 300 Nissan Drive
Canton, MS 39046
Phone: (601) 855-6010
How do you reset the brake sensor light in the dash board on 1992 Infiniti Q45?
check your break fluid, break pads, and ebrake switch! if were any other light like airbag then you would push the drivers door light swith five times with ignition on
