0
Jeep Cherokee
The Jeep Cherokee is a full-size SUV vehicle that came in two versions: the SJ model (1974 to 1983) and the XJ model (1984 to 2001). The chassis was based on the Jeep Wagoneer but had a 6.6-liter engine.
2,083 Questions
Your 93 Jeep Cherokee Sport is overheating?
The usual reasons are one or more of the following 1. Radiator cap bad (system must be pressurized to cool properly) 2. Bad themostat 3. Lower radiator hose weak. (at speed, the hose can callopse restricting the water flow) 4. The viscus fan is bad (this is the fan that is driven by the fan belt. It has a slip clutch) 5. Old or Improper coolant mix in radiator (should be 50% water/50% coolant) 6. Radiator needs to be flushed or rodded 7. Timing too high. NOTE: do not remove the thermostat. it is there for a reason.
I have had a broken filament in a brake light bulb do the same thing. they cross touch and allow power to cross into the other circuit. replace all brake bulbs. If condition still there also check the front turn signal bulbs. They all share the same circuit..
I would check the ground wire first just in case that is the problem. If not, get back to me with additional information.
How many gallons of gasoline does a 1993 jeep Cherokee 4x4 hold?
The gas tank on the 2014 Jeep Cherokee holds 15.8 gal..
How many quarts of oil do you need for a 1999 Jeep Grand Cherokee?
4.7 engine, 6 quarts
How do you recharge the air conditioning system on a Jeep Cherokee?
Using a set of a/c gauges put the blue hose on the low side (suction side) and the red hose on the high side (discharge side) and make sure that there is no freon in the system and if you have freon in the system then you will have to go to an automotive a/c shop and have them reclaim it for you.. Put the yellow hose on your vacuum pump and let it run for about 1 hour and then let it sit for 1 hour so that you can see if it will at least hold the vacuum pulled. If so then let it run for an additional hour and then start the recharging process remembering to keep the low side readings between 30 to 40psi and the high side between 200 to 250psi depending on the outside temperature…………….
Does the fuel pump in a 1998 Jeep Cherokee need to be replaced?
If the jeep takes a while of turning over to start or if it just won't start at all check to see if it is pumping fuel out. Also turn the key to the on position and see if you can hear the pump kick in.
How many catalytic converters on a 2000 Jeep Cherokee 6 cylinder?
They are located at the beginning of the exhaust just below the body of the car. They are easily found by following the pipe coming off the manifold, they actually look like mini mufflers and may be in any shape.
What causes your Jeep Cherokee 2000 to lean during a turn?
I'm assuming tight means seizing?
Lack of power steering fluid, defective pump, broken belt, seized front end parts (ball joints, tie rod ends, etc). Possible seized front u-joints if it's a 4x4.
Why do both headlights go out when you turn brights on in 1994 jeep cherokee?
I don't have an answer yet, so anything anyone can offer is appreciated. I would like to share though what I have done so others can do the same if desired: call the dealership and have them enter the issue in your file. Call the Jeep Corporate Service Line: 1 800 992 1997 to submit the problem...it might help to get a recall on the issue. Also, call the National Highway & Traffic Safety to submit the problem and receive a formal report from them to sign and return to the Nat High & Traffic Safety: 800 424 9393. Has anyone else had this problem with their lights? It's a serious safety issue that I hope is a recall soon so it's not an expense for the auto owners!
Why does 2000 jeep run hot at idle?
A lack of water in your cooling system will cause your 2002 Pontiac Sunfire to overheat. A malfunctioning thermostat can also cause it to overheat.
Where is the EGR valve for a 1995 Jeep Cherokee?
According to Alldata the 4.0L engine is not equipped with an EGR Valve. You don't have one on the 4.0
How much horsepower does your 1996 Jeep Cherokee Sport have?
Factory rated at 190 hp, 225 lb-ft of torque at the crank (assuming you mean the 4.0L I6 and not the old GM v6 that was used in the 80s)
Where do you add transmission fluid in a 1998 Jeep Cherokee?
The same place that you check the level of the transmission fluid. The tube that the dipstick goes in is so large so that the fluid will flow down it easily. However, you may need a special funnel, one that has a very long neck, in order to be able to get the fluid into the tube. These are sold at all auto parts stores, and many other places. Check the level frequently, to insure that you do not over fill the transmission.
Where is the horn relay located at on a 1999 Jeep Cherokee?
The horns are located under the passenger side head light behind the front bumper. You have to trace the wires back to the relay.
In your PCM not the alternator
Its built in the alternator be sure that you replace the alt with the same amp. alt it could be a 90 or 124 amp alternator. Replace the belt while you have the alternator off.
How do you reset computer in Jeep Cherokee 2009?
= How do you reset the computer on a Jeep Cherokee Laredo? = Matt all you need to do is unhook to negative post of the batery for a minute, reconnect the battery and computer should be reset. any recurring trouble codes proably still need to be adressed
Where is the fuse for power seats on a 1990 Jeep Cherokee?
the fuse 4 the seats is actually circuit breaker #11 in the fuse block located over the break pedal. this is identified in the owners manual.Another fuse link is located under the carpet.
How to replace antenna on 1994 Geo Prism?
Just did it... You have to buy an exact OEM replacement. Unscrew the antenna unit by removing the two screws. Pull out the remaining metal antenna and the wire. A plastic tube that houses the antenna will need to be removed. I was unable to remove the antenna cable as it is clipped behind the dash. I cut the wire leaving about 6 inches remaining above the roof of the car. Remove the inside trim along the top of the driverside door, all the way to the fron window. Additionally, remove the small trim piece along the edge of the door beside the drivers side dash. With the new antenna unit, begin to thread the antenna cable through the existing roof opening along-side the original cable that remains. As you thread the cable through the body, take notice of a hole in the body on the inside of the car above the drivers side door. You should see the new cable pass by the hole. Pull the cable through the hole.(I had to enlarge the hole to accomodate the plug that attaches to the radio. I used a dremel tool with a grinding bit to slightly enlarge the hole.) Once you get the antenna cable through the hole, pass the metal antenna and cable through the hole in the roof until you can mount the antenna housing to the roof using the two screws. Run the cable under the door trim and down under the dash. Make sure the new cable does not interfere with your steering wheel or and thnig else. I hope this helps you. I would have loved to see this before taking on this project. I just replaced the antenna on my 1994 Geo Prism and found that only one piece of trim needed to be removed. It is the piece with the fuse box door on the inside drivers side. Once you have it removed you have access to a plug and cable that runs from the antenna to the radio. Unplug the antenna remove the screws on the outside, pull the old antenna and cable out,put the new antenna and cable in, plug it into the cable running to the radio, replace the screws and trim, job done! I followed above answer with one modificarion. Only had to remove fusebox molding. Unscrew antenna from roof.cut antenna wire and leave as much as possible. Pulled out clear plastic piece. Taped end of new antenna wire to end I cut off old antenna wire. Pulled new wire thru and connected to wire that goes to redio. No grinding.
Bad smell coming from the heater of your 95 Jeep Cherokee what could cause it?
A bad smell coming from the heater in a vehicle can indicate a bad heater core. One way to check this out is to see if the smell is worse when you sit in the passenger seat. If it is, there is a good chance the heater core is bad.
Where do you put the jack on a 98 Jeep Cherokee?
The jack is located under the spare tire. If you remove the spare tire, you will see it in the center of the well. The rods used to raise and lower the jack are located under the back seat on the passenger side. The jack is located under the spare tire. If you remove the spare tire, you will see it in the center of the well. The rods used to raise and lower the jack are located under the back seat on the passenger side.
How do i bleed the breaks on a 1999 Jeep Cherokee?
The 1988 jeep Cherokee Laredo has the sealed cooling system. Many bloggers have posted instructions on how to bleed or burp by removing the rad cap. This does not exist on the 88. Here is what I have come across during my search ( I am currently attempting to bleed my system), that you need to remove the temperature sensor valve. There is a bolt near the back of the valve cover under the hood on the driver's side. There is a small temperature fitting on top of the bolt that is easily pulled off. This is the sensor that feeds your dashboard gauge. When pulled off the temp will read zero. This procedure must be done after the car has cooled off, otherwise you will end up badly burned and needing to replace the bolt you just launched after being sprayed by boiling hot coolant. To start, be sure that the sensor bolt is higher than the front of the valve cover. In other words you need to lift the back of the car or park on a steep enough incline so that the back of the valve cover is higher than the front. When the bolt is removed you will hear air bubbles escape and hiss out as it leaves the hole. Immediately replace the bolt when coolant begins to flow. This process will need to be completed 5 or 6 times and will take most of the day because after each attempt you need to run the car to temperature and let cool before trying again. This will fix problems related to the jeep running cooler than usual or over heating in heavy traffic. It will also fix the problem with your heater not blowing hot air. The bolt requires a 13m deep socket to be removed. It may also fix problems with leaking coolant.
What I did the other day was to Remove the upper radiator hose and finish filling the radiator that way. It can take forever trying to add through the coolant bottle and then it still will not take as much coolant as needed. Very frustrating, be nice to have a real radiator cap.
How do you loosen the tension pulley on a 95 jeep Cherokee?
Loosen the 15mm nut that holds the pulley to the bracket then back off on the 13mm adjuster bolt.
What kind of oil filter do i use for jeep Cherokee 1995?
one that filters oil, and screws onto the mounting plate and seals Try the same kind you removed
Your remote door opener may be the problem. It may be going bad. Leave the remote home and see if that solves the problem
