Lexus RX

~$400 on OEM parts + 8 hours of labor

I just looked at the sliding roof diagram in the RX300 (2000) repair manual. The motor is located at the front center of the roof opening. It looks like it's just in front of the sliding roof controls.

The cost of a Lexus bulb replacement varies slightly by the model of the car and the retailer. On average the bulbs cost between 7.50 and 15.50.

Hi, I have a2002 Doge Ram. The driver side sunvisor falls down when I go over a big bump or dont hold it when putting it up. I took it off and found the rod inside broken. Then, I did a little research and found out it is a common problem, design fault. I called the dodge dealer and he knew about it and dodge redesigned the visor. So now if you want to replace the visor, not only do you have to buy a new visor, but you also have to buy the little clip that the visor clips in to. I am going to cut down the back of the visor, see how it works inside, maybe come up with a repair and probably ruin it and have to cough up the 55.00 to buy a new visor.......

There is a small black hose sticking out from the passengers fire wall and has been leaking out water over the last couple of days from having the heater on inside the car. The hose is under the passenger side part of the car up by the

fire wall or heater core area. Is this normal for this car? Is it a cool off or overflow hose?

The engine coolant temperature sensor is located at the timing belt end of the engine on the water outlet casting.

You need do diconnect the front differential, and then cut the red wire. After that try again. If it still doesnt work, take it to the dealer for a checkup. This is happening because in cars from japan, they use a different lockng mechanism. At you last checkup, your mechanic probably used the technipue for testing doors used for American-made cars.

yes u can, but there will be some loss of horsepower, other than that u're ok.

pry it off with a rusty butter knife

For a second generation IS250: Hold down the the odometer reset button and press the start engine (without your foot on the brake to prevent from starting) to switch to the acc. mode, continue holding the reset button for about 5 sec until the visual countdown ended et voila, your system has been reset.

interior trunk button wont work

that he must remove to get to spark plug rear of the cylinders

The PCV valve on a 2002 Lexus RX300 is located on the passenger side of the car underneath the hood. The valve will be on the rear valve cover.

I own a 2008 es350, so I for sure this works for 2007-2010 es350.

At the bottom of your nav screen,there is a little panel with the

Lexus logo on it,using your thumb nail,for the bottom push up,

the panel will come off.Push menu botton, then push the on screen

map DVD prompt, upper right corner. then push DVD eject prompt

on the screen, lower left corner. the DVD will slide out of a small slot.

You should be able to take it from there.

This Lexus maintenance light illuminates every 5,000 miles driven on the vehicle. This is a reminder light that will indicate when maintenance service is needed.

The Lexus is250 has two oil quantity possibility's. One is 6.6 quarts of oil , one is 6.8 quarts of oil.

The Lexus RX300 has the most common hook-end wiper arms. See Sources and Related Links below for installation videos. Also, purchase the replacement blades first and there will be additional instructions/illustrations on the replacement packages. Locate and press the tab or button where the wiper blade is inserted into the hook of the wiper arm and pull wiper blade out of hook. You may have to rotate and flex the blade to make enough clearance for the hook to pass through.

Toyota/Lexus uses a direct mount ignition coil for each spark plug so you have six of them on your engine. If you have a bad coil the engine will run rough, the vehicle will shake, and your check engine light may light. The trick is to find which coil is bad. You may be able to get a free scan at a local auto parts store(AutoZone does it, maybe others) that should tell you which cylinder is misfiring. The cylinders are numbered like this as you look at the front of the vehicle 1 3 5

2 4 6

2,4 and 6 are easy to change since they are in front. Remove the vanity engine cover by unscrewing the L emblem on top of the engine and remove 3 allen (4 mm or 5/32) screws at the top front of the cover. You can then see the 3 front coils. Disconnect the wiring connector by pushing on the clip that holds it in place and wiggle and pull, don't pull on the wires though. Remove the 10 mm bolt that holds the coil down and then twist and pull the coil off the spark plug. I have seen cracks and arc tracks on the shaft of a bad coil but just because there are cracks doesn't mean it's bad. I have switched a suspected bad coil to a different cylinder and rescanned to verify that the code changed to that cylinder. 1,3 and 5 are much more difficult to get to but can be done by removing a couple small parts to allow

access. There is a good procedure on Lexus club forums called DIY Spark Plugs (if you have the patience). Try searching on Google for it. The individual coils run $80- 100 at stores, slightly cheaper online. On Amazon I saw a set of 6 for around $225.

how do i change front interior light for lexus rx 300 2004 model

2000 Lexus RX300 brake light bulb replacement: Purchase the correct replacement brake light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement brake light bulb information. Then consult your owner's manual for the replacement procedure. As simple as it sounds, the owner's manual is the best place to start for brake light bulb replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).

behind the glove compartment. Couple of tabs need to be rotated 1/4 turn, then box drops down and filter is obvious

The plastic panel the houses the light assembly needs to be removed. The plastic panel is clipped in. To remove it carefully pull it out starting from the left side of the panel at the top and moving down to the right ending on the right. Be careful that the clips don't fall of the plastic panel. You may need to use some strength but it will come off. The light assembly is attached to the rear door. To remove it press down on the top of the red cover. Turn the light socket counter clockwise until you can pull it out. To remove the light bulb pull it out of the socket. It is a 921 18w bulb a very common high mount stop light bulb. The bulb can be purchased at most car parts stores such as Canadian Tire, Napa auto parts or Lordco auto parts. Push the new bulb into the socket. To replace the socket match it up with the lens and turn clockwise to lock in place. Make sure the wires are on the left and the open end of the lens is toward you. Install the assembly back on the door starting with the bottom and snap it back in place. Replace the plastic panel and reclip it by punching it with the side of your fist starting at the left. Punch the entire panel to ensure all clips are reclipped.

Late model RX330 were and RX350 are made in Japan and Canada.

open the glove box it should be in the back i have the same year but the 400 and that is where mine is the price for a new one should be no more than 25 dollars