Mechanical Engineering

If the generator is to maintain the same rpm and power output, then a heavier load will increase the diesel consumption.

The revolutions per minute the generator runs will increase as the load increases, thereby resulting in an increase in diesel consumption to maintain the high rpm.

A Generator has a governor which attempts to maintain frequency at 60 Hz for North America. For the generator to increase the power output at the same frequency, the governor will increase the fuel and air to the engine. The fuel consumption will not be linear because of the curves associated with the particular engine. The fuel to KWH is know as the heat rate curve for the generator.

knurling

In many typical installations, it is used in strain gauges.

Eat a banana.

It only takes half the effort to move an object but twice the distance

It is the point at which the stress-strain graph of a material deviates from being a straight line. It is the point at which a material stops obeying Hooke's Law

Architecture if you are more of the artistic type, but also somewhat interested in math and physics, which you will need to understand if you are to be an architect. If you are very much into mathematics and physics, but not interested in art and design, then mechanical engineering would be better for you.

So know how to build things instead of pile of I-beams and piles of cement willy-nilly. Perhaps building not your thing. So, it is easier to know the length, width, height better, without having to gess.

The fee structure will vary depending on the courses taken. You will need to check with each college.

Most roller bearing systems help create a decreased amount of friction between items, such as a wheel and the axle the wheel has been centered on. This allows the wheel to spin freely on the axle without being bound by the force of friction. It also decreases the force of drag on the wheel as it spins. This allows a wheel to be more easily pushed by any power source applied to it, whether it's an engine or a person pushing a car.

Smoke rising from a flame. At first the smoke rises with laminar flow before becoming turbulent just a few centimetres above the source.

The ultimate tensile strength of a 12.9-grade tensile bolt is typically around 1,220 MPa. This means that the bolt can withstand a maximum tensile load of 1,220 mega pascals before failing. It is important to note that the actual strength can vary slightly depending on the specific manufacturer and production process.

There are several examples of BEAM robots which are line followers. BEAM robotics uses simple logic chips for the "brain" like the 74AC240 which costs $1 or so. The rest of the components are discrete components which means no microcontrollers are involved - only the usual parts like diodes, resistors, capacitors etc. I've included 2 links in the "Related Links" section below.

refractory metals have high melting points and are used in extremely hot environments; if expansion coefficient is lower this prevents high stresses that can develop due to thermal gradients during the high heat up. It helps to have high thermal conductivity as well

the main reason might be that the percentage of carbon increase the hardness of material (steel ) and ductility would decrease

You create a table that you're on one side and the other at your jobs

Well,the well known negative affects of anamolous expansion are:- 1.Due to anamolous expansion the pipes usually burst in winter,because the expansion of water in winter is much more than is much more than the expansion of pipes. to avoid bursting the pipes are covered wid insulating material.

It should be less than 30lacs INR

No but copper or brass willNo

Going cold, not very much - it may get a 2% higher at cryogenic temps. Going warn, it does decrease by up to 20% as you get to 1000 degrees F ( from 30 Msi to 24 Msi)

A shaft bearing is a low friction support device for a rotating member of a mechanical machine.

it will start to change slowly after 20 degrees C. At 400 degrees C it will degrade quickly - almost linealy to 800 C where it will hve reached approx 10% of its yield strength.

The smaller the gage the thicker the material; therefore, for the same material, 14 gage is stronger.

St35

Two wheels are mounted on either side of the rigid axle .When one wheel encounters the bump, both the wheel do not execute parallel up and down motion So it gives rise to gyroscopic effect and wheel wobble. Rear driving wheels mounted on live axle suspended by laminated leaf springs and shock absorber

Abhijit jain

student at medicaps institute of technology and management.