0
Mercury Villager
The Villager was a minivan manufactured by Ford Motor Company from 1993 to 2002, and was a rebadged version of the Nissan Quest. Designed by Moray Callum, the Villager featured a five-speed automatic transmission and a front engine, front-wheel drive layout.
1,605 Questions
What to do when 98 Mercury Villager battery light is on?
This indicates a no-charge situation. Most likely the alternator is bad.
How do you replace the oil pump of a 96 mercury villager?
The oil pump assembly is behind the front timing cover and fits around the crankshaft snout. Needless to say, this requires considerable disassembly to get at.
What is the oil capacity with a filter change for a 2000 Mercury Villager?
According to the 2000 Mercury Villager Owner Guide :
With engine oil filter change the 3.3 litre V6 engine takes :
( 4.0 litres / 4.2 US. quarts of 5W-30 engine oil )
Why would the knock sensor trouble code keep coming on?
depends on what kind of car it is. On most supercharged, turbocharged,and cars with high compression ratios the knock sensor code would come up because you didnt put high octane fuel in the car. the lower the octane rating of the fuel, the more unstable the fuel is under pressure, which means the fuel would ignite before the spark ignites it, causing the timing to be off and the Check Engine lite to come on
ANSWER from smokingallowed....
I just came from there. I can tell you I kept getting a P0325 code, which is Knock sensor circuit 1 fault. I have another knock sensor sitting around,so I swap them out. The code kept coming back. I KNOW they work because to test them,get your meter, clip the red(+) meter wire to the the plug-in side of the sensor and the black(-) meter wire to the caseing of the sensor if its the one wire type. If its 2 wire type connect the two meter wires to the two sensor prongs on its plug on the sensor. Then set the meter to the lowest AC setting.(Not DC) Knock sensors produce AC voltage. Then bang on the side of the sensor and watch the voltage spike..If it don't change the sensor is bad. But anyway, It's still doing the same even with different knock sensors. I'm starting to think bad gas,but there was no knock. So I removed the sensor again took a wire brush to the threads of the sensor AND the thread of the block where itscrews in. I learned that don't overtighten it.It should be torqued to Appx. 14 ft. lbs. I set mine at 10lbs. But first I wrapped it in a towel so it wont bang on anything and then drove the car with it being unscrewed from the block. The code STILL came back. So I double check the threads for cleanliness. Screwed the oridgenal sensor back into the block. I tested the plug that comes from the car for voltage.It was somthing low like 4 or 5 VDC in which it is supost to be. Then pluged it back in and THAT was the problem.NO MORE KNOCK SENSOR CODE P0325. In short words,MAKE SURE that the sensor has a good clean connection where it screws into the block...because that is the ground for the sensor and if its not makeing good contact with the block you will have a P0325 (Knock Sensor Circuit 1 Fault (or short) I also replaced the knock sensor plug on the 97 z24..... So remove the sensor,test it as outlined above,clean the sensor threads, and the threads on the block, twist the wire that you will be plugging into the sensor a few times So you can be sure the plug is pluged in very good. I have read that these are screwed into the water jacket,but the past 8 knock sensor I have removed from blown 2.4L DOHC engines NONE were screwed in the water jacket.
Dont get the above code mixed-up with the P0326 CODE. Which is Knock Sensor Circuit Performance. That will be the sensor is failing or has already failed, or the 4 or 5 volts is not reaching the knock sensor.
Where is the cam sensor located on a 2000 Mercury Villager sport?
The cam sensor is located in the distributor. The cost of a distributor is about $250.00 and up. get the cam sensor checked first, then if needed, replace. Use a Haynes Manual or something else to guide you thru the replacement process. It's easy to do.
Where is the starter relay located on a 2001 mercury villager sport with a 3.3L automatic?
start inhibitor relay located next to battery in fuse/relay compartment
Where is the CD player on mercury villager 99 state model?
The CD player, if it has one, is right in the radio. If you mean the changer, look below that or under the passenger seat.
Where is pressure regulator on 95 mercury villager?
If you mean the fuel pressure regulator, it's on the end of the fuel rail near where the fuel line attaches.
Where is the starter relay located on a 1998 mercury villager?
All major relays are in the relay box under the hood.
Where do you add transmission fluid on mercury villager 1997?
Transmission fluid is added through the dipstick tube.
Where is the neutrl safety switch located on a 1995 mercury villager gs?
It's part of the range switch on the transmission.
Where is the cam shaft position sensor in a 1999 Mercury Villager?
The camshaft position sensor is integral with the distributor. So, have it checked carefully by a professional because, if the sensor is faulty, the distributor must be replaced. That can get ugly expensive real quick.
How do I remove the rear wiper assembly on a 2000 Mercury Villager?
First Raise the rear wiper blade assembly out away from the back glass it will pull away from the body of the van.
next there is a plastic clip located on the wiper shaft pop this clip off.
After you have removed the clip slid the wiper assembly out of the slot.
This should allow complete removal.
Next step re-install the new wiper in reverse.
Where is the 1997 mercury villager power steering pump located?
on the front passenger side of the vehicle it is the pump that has the third belt n it
The clock spring is part of the Air bag system. It keeps the connection on the air bag while turning the steering wheel. To get to it you MUST DISCONNECT the battery first. This is a must. Then take the air bag from the center of the steering wheel. The bolts are on the back of the steering wheel. Remove the lower cover at the ignition switch. unplug the wires going to the steering wheel. That is the clock spring wiring. When you remove the steering wheel the clock spring is right there. Dealing with the air bag is DANGEROUS if you are not familiar with this stuff spend the money to have it fixed. Your safety is more important than saving a couple of dollars. Call your local dealer or go online to find the price of the clock spring. I don't know how much it cost.
What size Torx bit do you need to remove the caliper of a 2000 Silverado?
T55 TORX BIT ON THE FRONT 12MM SOCKET ON THE REAR!
The Blower Motor Resistor Pack is defective. Replace it.
It is located on the passenger side by the blower motor. Very easy fix, 1 clip and 2 screws. Check RockAuto.com AIRTEX Part # 4P1402 for price and a great picture so you know what you are looking for.
How do you open the hood of a 1998 Mercury Villager?
Pull the hood release under the dash at the left side.
Can the oil filter housing be replaced?
That is a poorly worded question as oil filters have not had housings since the 60's. All oil filters are normally screw-on cans and are totally self contained. However, if you removed the filter and have an outer shell and a paper filter in your hand, you are in big trouble because the threaded filter can base is still on the mount. Now, if you are talking about the oil filter mounting base, it can be replaced by removing three bolts. Check to see if it is available separate from the oil pump.
If you smell gas from your vehicle it probably indicates a leak. Even a tiny leak will produce a fuel smell. If there is nothing obvious leaking from the fuel lines, pull the vacuum hose off the fuel pressure regulator, if there is any smell of fuel there or if gas is present, it is leaking and needs to be replaced.
What is the best replacement battery for a Mercury Villager van?
I prefer to use Duracell batteries . . . they keep going, and going, and going . . . = = Answer = = Any good national brand battery with at least 850 CCA (cold cranking amps) Then have your charging system checked.
