0
Pontiac GTO
The Pontiac GTO is a car produced between 1964 and 1974 by General Motors’ Pontiac division. GM subsidiary’s Holden also produced this car model in 2004 to 2006. GTO’s 21st century version is a left-hand drive Holden Monaro.
642 Questions
How do you reset the service light on a Pontiac?
Have vehicle scanned to determine the problem and have codes cleared
Maximum horsepower for stock 2005 LS2?
Stock HP on a stock LS2 is 400hp at the crank. With an average drivetrain parasitic loss of 15% this equates to roughly 340hp at the rear wheels --LS2 GTO Owner
How do you apply on overhaulin?
Dear sir i like you people to get hold of my sister for my 1949 chevelot pickup.my sister is felicia brewster.i like to fixed my truck .i'm in oversea with the military david weir thank you.
Well, I'm no expert when it comes to frame/body relations. However, I've found that one of the best places to get parts (or anything for that matter) is eBay. All you need to do is type in the year and make your looking for in the search box, and chances are you'll find someone selling what your looking for. I would also check out Hemmings.com in the parts section. Hope this helps you some.
AMES.com
The 65 to 67 frame is the same. You should also be able to use the same year Chevelle, Cutlass, etc. That being a big SHOULD. Hollander interchange guide available at most salvage yards will help with that.
Parts sources, Used.....car-part.com New...Ames, year one, classic industries, OPG, Goodmark Ind, Performance Years....Just to name a few.
Where is the fuel pump resistor on a 98 gtp?
Right side frame behind washer bottle assy. Can be accessed by loosening inner fender.
How do you bleed the clutch in a 2005 gto?
Make sure the master cylinder is kept full of fluid at all times and put your helper inside with foot on clutch petal, with the car jacked up and stands in place locate slave cylinder on drivers side and place a 11mm wrench on the bleed valve,. have the cockpit man push on the petal and hold it down, then open valve and let air and fluid escape being careful not to get fluid in eyes, tighten valve and tell helper to let petal return. its petal down-loosen-tighten-petal up. Repeat this process several times to remove air.
What is the point gap setting for 1967 GTO 400?
.020 If you have a dwell meter it is 30 degrees of dwell.
How do you fix a GTO idling problem?
Others claim to have experienced idling problems with their GTO's aswell before their its' engine computer learned the new flow of the LS1Speed intake. Initially, the car had a bit of a hesitation to startup when the key was turned, but that issue went away as the computer learned. Probably the most noticeable effect the system had was that it made the intake snarl much more audible, which is always a plus.
Did the 1966 gto come with a 454 engine?
The 1966 GTO only came with the 389 cid motor. You could, however, get it with the standard 4 bbl quadrajet Rochester carb or the optional tripower (3x2 carbs).
How do you remove and install an ignition key tumbler from a 1970 Pontiac GTO?
steer wheel must come off,gently
push and turn horn contact wire, now you will see a steel plate this is called a lockplate
it lock wheel from turning when key is out, you need a tool to remove this plate, auto zone lends tool, this tool pushes plate down enough to remove snap ring that hols plate onto shaft, once plate is out remove turn signal lever unscrew it lefty loosey
now remove phillip
screws tha
hold turn signal switch also remove 4 way hazard switch. now look at new lock cylinder you will see a button that moves in and out when tumbler is turned now find the button on old switch and push this button on old tumbler to remove switch make sure key if foward
and pull on tumbler while you are pushing release button, install new cylinder put turn switch screws back put lock plate make sure you line up the keyway
on plate slip lock ring ovev
shaft install lockplate
tool depress enough till you see snap ring grove slide snap ring in, now look at end of steer shaft and splined
hole on steer wheel ther
is a alignment notch so you put the wheel centered.put
turn lever and hazard switch, simple right
Not in the GTO. You had a choice of 389 Tri-power (19,045) or 389
4 barrel. ( 77,901)
What is the problem when your key won't turn over in a Pontiac GTO?
In my 2004 Pontiac GTO, I had that problem. I took it to the dealer and they cleaned out the ignition with some lock cleaner that you can purchase at home depot and they also cleaned the key .
Will a 1970 442 12 bolt rearend fit in a 1967 gto?
Yes, but the 1968-1972 rears are 1" wider than the 1964-1967 rears. This may cause tire to fender interference problems.
How many horsepower is a 6.5 liter 389 engine 1965 GTO?
6.5 liter 389 4bbl puts out 335 hprsepower at the crank. The tri power puts out 360 horsepower at the crank.
How do you adjust idler to 1985 pontiac fiero?
There is no idler pulley on this year Fiero so you must mean Idle Speed.
It is most likely that if the idle is high and it wont slow down automatically, 1500 or so, that you have a cracked EGR pipe between the intake and the EGR valve.
There are replacements available on line from companies like "The Fiero Store"
In it's original production run, the last GTO was made in 1974. However, it was hardly a GTO, it was more of a glorified Nova than anything else.
What is the weight of a 1971 gto?
Options will change the base figures but Hardtop was 3,753 and convertible weighed in at 3,802.
What is the correct numbers for a 1966 gto bumper jack?
All bumper jack bases were painted blue and measured 6 x 6". Two different part numbers could have been used for the rack. 9783363 (keystone shape) or 9781295(square shape). The handle was the same for '64-'67, Part # 9775167 . It was blue and doubled as a lugnut wrench. It had a rubber sleeve # 9785869 in '66 and '67 only. The 5 1/2" bolt that secured the jack was unfinished metal (part # 535782 ) as was the wing nut (9785616).
