0
Subaru Legacy
The Subaru Legacy is a mid-sized car produced by Subaru since 1989. It is available in five generation models, and comes as a wagon or sedan. This model serves as the flagship car of Subaru.
1,507 Questions
How do you replace a dashboard light bulb in a 2003 Subaru Legacy?
Generally speaking, you have to remove various dashboard panels in order to gain access to the bulb(s) that need to be replaced. Which panels, and how to remove them, depend on which specific lamp has failed. Dashboards have dozens of lamps in them -- some for illumination (so you can see a gauge or label at night), some as indicators ("on", "fasten seatbelts", etc.).
For example, in my 2001 Forrester, the illumination lamps in the HVAC (heat/vent/air conditioning) console failed. During the day, this did not matter, but at night, I had to feel for the knobs to tell what they were set at. I discovered that the HVAC console was illuminated by two lamps (distributed across the entire HVAC console face by a series of clear plastic light pipes). Replacing the lamps themselves is a simple matter of pulling the bulbs from the lamp-holder sockets, and inserting new ones. However, to gain access to the lamp-holder sockets, I had to:
- Remove emergency brake cover by removing two screw caps, two screws, and pulling. This unlocks the gearshift cover.
- Remove gearshift cover by unscrewing gearshift knob, then pulling. This unlocks the bottom of the center dashboard cover
- Remove center dashboard cover by pulling.
- Disconnect two power connectors from center dashboard cover.
- Remove left lower dashboard cover by removing one snap, two screws, and pulling.
- Disconnect wiring for two switches and OBD-II diagnostic socket from left lower dashboard cover, by pushing plastic tabs. (Can't do this before because they're covered. Have to do it after, otherwise dashboard cover dangles)
- Disconnect vent selector control cable, using pliers to pop it off pin. (Exposed by removing left lower dash cover.) This is needed to free the HVAC console later.
- Remove right lower dashboard cover and glove compartment by removing one snap, six screws, and pulling.
- Disconnect hot/cold and fresh/recirc control cables. (Exposed by removing right lower dash cover). This is needed to free the HVAC console later.
- Remove radio bracket (with radio still in it) by removing four screws and lifting out.
- Disconnect wiring from radio by pushing plastic tab.
- Reach through hole left by radio bracket, and disconnect three wiring connectors from back of HVAC console. (Not enough slack in HVAC console wiring to pull console first. There is slack in radio wiring to remove radio.)
- Remove four screws from HVAC console.
- Remove HVAC console from dashboard.
Re-installation is basically just reverse of removal.
As you can see, this task is made much harder by all the steps you have to do to gain access to the bulbs. None of it is actually all that hard as far as techniques go -- it is mostly just screws and snaps. The trick is knowing which screws and covers to remove, and in what order. I bought a Service Manual for my Forester to make it easier for me.
The only reason I even bothered replacing the lamps was that I had to tear the dashboard apart for something else anyway. (The HVAC blower switch failed.)
*** For the Legacy/outback go to: http://www.subaruoutback.org/forums/99-do-yourself-illustrated-guides/18175-replacing-lights-instrumet-cluster.html
Why do I smell burning rubber after replacing the clutch in my Subaru?
The smell comes from the new clutch and usually because you are riding it, or slipping it. Being a new clutch it reacts to almost any pressure. Stop riding or slipping it and this will stop.
Is there a Picture of thermostat in 2001 Subaru Outback?
Go to: http://opposedforces.com/parts/legacy/us_b12/
Select Body Style, Engine Type, Transmission, etc.
Go to Cooling System. Select Water Pump; You should find Thermostat, Gasket & applicable part numbers...
Is the Subaru Legacy a good family car?
"Yes, I actually own a Subaru Legacy Outback Wagon, and while my family of 3 is small, it is our first choice for all road trips. It is big enough for all of our luggage, but easy for my wife to hand our toddler snacks and toys."
to set on fire
In an automotive sense, ignite is the "explosion" of the fuel in the head cylinder when the spark plug "fires". The "explosion" forces the piston down to rotate the crankshaft and provide power to the engine.
Is the 96 Subaru legacy outback 2.2l engine interference or non interference?
non-interference. there seems to be a lot of confusion about this. the 2.5l's are interference, the 2.2l's are non-interference.
How much does it cost to replace the clutch on 1998 Subaru Outback?
If you go to a normal shop, the parts are rarely the issue. Clutch jobs run from $600-800 depending on the reputability of the shop and the area of the country you are in. Always check the warranty or lack thereof. They will always make up charges to get it up as close as they can to $1000, no matter if it is a subaru, SAAb, or chevy.
There will be shop fees, energy fees, disposal fees, tax, and labor at $90/hr or better. If you really want the listed labor rate go to alldata.com, get a membership, and get the actual hours of labor for the job. If they charge more hours than in alldata, go to a different shop. These are standards based on the make of the vehicle. Make sure they itemize all charges before you take the car in.
Also, BE SURE TO CHANGE THE THROW OUT BEARING. If it is integrated into the clutch slave cylinder, replace with a NEW ONE. Make sure you specify NEW hydraulic clutch fluid in the entire system. If it is a cable clutch, change the cable too. You will kick yourself later if you do not replace all the components at this time. Also, make sure the flywheel is resurfaced professionally, not just a brillo pad on a drill. Pilot bearing has to be replaced too.
Is the tape player wiring plug the same as a CD tape player wiring plugfor a 97 Subaru Legacy?
Yes. Its only an audio output. If you want pin outs, do a search in Nasioc.com under Impreza stereos. I can't remember the exact link. Have fun Osei
How do you remove the stock stereo from a Subaru Legacy Outback?
Easy one. I bought my replacement stereo from Crutchfield, who also supplies wiring harnesses for each individual car, First, remove screws from console and shifter arm (be careful) remove carefully console and center trim and set aside. Remove bezel (cover) from around radio by 2 screws under bezel. Remove bezel to expose radio assembly. 4 screws hold in radio and storage compartment. (unhook battery early) Remove 4 screws and radio assembly will slide out easily. Change out stereo (lots of mounting holes to choose from) by removing antenna lead and wiring harness plug. Attach wiring harness plug from crutchfield (Easy, solder or tape white wire to white wire, orange to orange, etc...) Plug in harness end to harness end, and re-install in reverse order. No botched wires, jerry-rigged connections, and using factory harness enables speaker setup and looks like it was built that way. total cost; 130.00 plus your time. Crutchfield supplies everything, and has several choices for stereos. Easy and professional. I have used same stereo on 3 cars now, just needed different wiring harnesses. Enjoy and don't forget to reconnect battery.
How do you set the time on the timing belt of a Subaru Legacy?
WARNING!! its not a good idea for you to adust the timing because it very dangerous for your car, your safety. i recommend that you see a mechanic. doing this yourself requires a lot of experience in car mechanics. if you have the experience. then you observe the timing belt and the pullys. also contact the subaru dealer and ask to be transfered to the mechanic and ask him/her for the timing configuration for your car.
Where is the transmission dipstick located on a 1995 Subaru Legacy?
is located in the passanger side of the engine. almost right above the universal joint that powers the tires/ it's on the bell housing if you open the hood and look close you will see a 2 inch curved handle/ it's verry small to see but if you take your time you will see it. the dipstic itsekf its about 4 inches big If it is manual transmission, the dipstick is on the passenger side. If it is an automatic trans, then the dipstick is on the drivers side, buried under/behind the rubber heater hoses, almost under the master brake cylinder.
Is it OK to tow a U-Haul trailer with a Subaru Legacy wagon?
Yes, you should be able to tow a 6x12 utility trailer, use the uhaul website to make your reservation and it will verify that your car can tow the selected trailer during the process.
Where is the knock sensor on a 1995 Subaru legacy?
I believe the knock sensor is housed at the top of the oil pump. It should be visibly located under the alternator. It's wire should share the same main cable routing as the oil pressure sending unit which is just above the knock sensor and under the left side of the alternator when standing in front of the car. Nothing posotive here, don't quote me
How difficult is it to remove and replace a 2.5 liter engine in a 2000 Subaru Legacy?
Easy if you have an engine hoist and experience doing it. The most annoying/difficult and time consuming part is just unplugging everything. Oxygen sensor, throttle position sensor, coolant temperature sensor, etc... all need to be unplugged, then plugged back into the correct place on the new engine. Every time I've done an engine swap, there will be one plug that didn't get plugged in, or plugged into the wrong place, and then you have a really fun time finding what you did wrong. I recommend you buy a service manual, and make friends with someone who's done engine swaps before.
How to check power steering in 1997 Subaru Legacy Outback?
Hi,
My answer may apply to you. My girlfriend has a 99 subaru legacy and the pwr steering fluid was leaking on the garage floor. We bought a rebuild kit for $45. from the dealer and I tried to repair it. I went to the public library and they had Chiltons manual online (free of coarse) that I was able to down load and copy on the step by step process on how to take off the whole Pwr Steering unit from the car so i could "rebuild" it. The site has instruction on how to bleed the system when you're done. Once the unit is out of the car you can look the unit over to see where your leak is happening. You didn't share in your question what problem leads you to believe you need to "check" your power steering so I'm not sure what you need to do. You can respond to this site I guess if you need more info. I did find the dealer wants about $360 for a new pump. I went to a rebuild site and found where I can have a rebuilt arrive at our house for $125. Installing is pretty easy. Rebuilding with the parts kit left me with some questions as I didn't feel comfortable taking some parts out for fear of not being able to get some back in just right. Small pins and such. One seal seemed pressed in. The pulley nut is regular threaded. Good luck. Mariner356@hotmail.com
What is the location of the thermostat on a 1995 Subaru Legacy Wagon?
Follow the lower rad hose from the rad to the engine, the thermostat is located under the thermostat housing on the engine end (2X10mm head bolts). Notes: 1) if these bolts have not moved in a while it is likely best to spray them with oil for a bit, they are steel bolts in an alumnium housing located in an area almost impossable to get a drill to, so be careful. 2) using an aftermarket thermostat can give "mixed" results, the best choice is a Subaru OEM thermostat and gasket. 3) use a bit of grease on the bolts when replacing them for "next time".
Can you twin turbo a Subaru sti?
The way the EJ engines are designed, and the engine compartment of the STI itself, is specifically suited to fit one turbo. But, anything is possible with custom fabrication. Doing something like twin turboing an STI though would cost too much money, you're looking at over $20k.
It would be a much better choice to simply put a larger turbo on. Less money, more simplicity, more reliable, easier to work with, probably faster as well.
How do you change a headlight bulb on a 2010 subaru legacy?
You have to go from the wheel well.
Pull back the fender liner toward the front and you will be able to reach your arm in there and remove the bulb. It may be helpful to remove the wheel in the process, if you need more more to work with.
How can I find a 1997 Subaru legacy outback ltd owner's manual?
check this link, it did helped me get info on my 97 subaru outback.
http://hp.auto.ru/Subaru%20Legacy/1997/
cheers!
How do you remove headlight lens cover on 97 subaru legacy for cleaning?
The headlights are sealed units, unfortunately they do cloud over a bit with age. Try a cut and polish on the outside of the lens to clean them up a bit, but you would have to go to a plastic welder or similar to get them to remove the housing, and even then, cleaning them may not remove the cloudy effect.
Does the stock stero in a 1994 suberu legacy have dc conecters?
If you are asking if it operates on DC, the answer is YES. It has a 12 volts DC in connection.
What is the GM legacy program?
The GM Family Legacy Program provides eligible children of certain deceased GM retirees and surviving spouses the opportunity to continue.
