Acura TL and TLX

To change the thermostat in a 2001 Acura TL, first ensure the engine is cool and disconnect the negative battery cable. Drain the coolant from the radiator, then remove the upper radiator hose from the thermostat housing. Unbolt the thermostat housing, replace the old thermostat with a new one, and reassemble by reversing the disassembly steps, ensuring to refill the coolant and bleed any air from the system. Reconnect the battery and check for leaks.

A 1999 Acura TL typically uses 5W-30 motor oil for optimal performance. It's recommended to use high-quality oil that meets API (American Petroleum Institute) standards. Always check the owner’s manual for specific recommendations and any oil change intervals.

To replace the alternator on an Acura TL, first disconnect the negative battery terminal to ensure safety. Remove any components obstructing access to the alternator, such as the drive belt, air intake, or engine cover. Unbolt the alternator from its mounting bracket and disconnect the wiring harness. Install the new alternator by reversing the steps, ensuring all connections are secure and the drive belt is properly tensioned.

To remove the glove box on a 2003 Acura TL, first, open the glove box and locate the damper arm, which is usually attached to the side. Detach the damper arm by either popping it off or removing the clip. Next, remove the screws or bolts securing the glove box to the dashboard. Finally, gently pull the glove box out to detach it from the dashboard assembly.

To replace the turn signal on a 1999 Acura TL 3.2, first, open the hood and locate the turn signal assembly. Remove the screws or clips securing the assembly and gently pull it out. Disconnect the wiring harness, then remove the old bulb by twisting it counterclockwise. Insert the new bulb, reconnect the harness, and reinstall the assembly, securing it with the screws or clips.

To change the shifter solenoid on a 1999 Acura TL, first, disconnect the battery to ensure safety. Remove the center console by unscrewing the necessary screws and carefully lifting it out. Locate the shifter solenoid, which is typically found near the transmission, and disconnect the wiring harness and any bolts securing it. Replace it with the new solenoid, reattach the wiring, and reassemble the center console before reconnecting the battery.

Service code A14 on a 2006 Acura TL indicates that the vehicle requires an oil change (A) and additional services related to the 15,000-mile maintenance interval (1), which includes a tire rotation (0), and a replacement of the cabin air filter (4). This code prompts the owner to perform these essential maintenance tasks to ensure optimal vehicle performance and longevity. Always refer to the owner's manual for specific service details and recommendations.

To remove the door panels on a 2002 Acura TL Type-S, start by carefully prying off the plastic cover behind the door handle and removing the screws underneath. Next, use a flathead screwdriver or a trim removal tool to detach the clips around the edges of the panel. Once all screws and clips are removed, gently lift the panel upwards to detach it from the door frame. Be cautious with the wiring harnesses connected to the power windows and locks, disconnect them before fully removing the panel.

The service due soon code A5 on a 2005 Acura TL indicates that it is time for scheduled maintenance. Specifically, the "A" refers to an oil change and oil filter replacement, while the "5" signifies that the vehicle requires a tire rotation, a brake fluid replacement, and a multi-point inspection. It's important to address these services to maintain the vehicle's performance and safety.

In the 2013 Acura TL, the Positive Crankcase Ventilation (PCV) valve is located on the engine's valve cover. Specifically, it can be found towards the rear of the engine on the driver's side. To access it, you may need to remove some components, such as the engine cover, for better visibility and reach.

On a 2001 Acura TL, the transmission fluid dipstick is located near the back of the engine bay, towards the driver's side. It is typically marked with a bright-colored handle, often orange or yellow. To check the fluid level, ensure the vehicle is running and at operating temperature, then pull the dipstick, wipe it clean, reinsert it, and check the fluid level against the markings. Remember to add fluid if necessary, using the recommended type for your vehicle.

To reset the immobilizer on a Peugeot 106, first ensure the vehicle is in the "Off" position. Insert the key into the ignition and turn it to the "On" position without starting the engine. Leave it in this position for about 10 minutes until the immobilizer light turns off, then turn the key back to the "Off" position and try starting the engine. If the issue persists, consult the vehicle's manual or a professional for further assistance.

The offense description "FL TO PY TL" likely stands for "Flight to Avoid Police Traffic Law." This abbreviation suggests that the offense involves a vehicle fleeing from law enforcement in violation of traffic laws. It typically indicates a serious traffic-related crime, often related to reckless driving or evading arrest. Specific meanings can vary by jurisdiction, so it's important to refer to local statutes for precise definitions.

TL, BL, WL are commonly used abbreviations in the field of networking and telecommunications. TL stands for Transmission Loss, which is the amount of signal power lost as it travels through a medium. BL stands for Burst Length, referring to the number of bits transmitted in a single burst. WL stands for Wavelength, which is the distance between two peaks of a wave in the electromagnetic spectrum.

Well, honey, an example of an active restraint is a seatbelt. It's not just a fashion statement, it's there to keep your butt in place during a car crash. So buckle up, buttercup, and stay safe out there on the road.

They are used primarily by Japanese and other Asian automotive manufacturing companies. They are the equivalent to the following standard Cartesian coordinate system axes. X=TL (traverse line) Y=BL (buttock line) Z=WL (water line)

Well, removing a gas tank can be a delicate process, much like painting a happy little tree. First, make sure to disconnect the fuel lines and electrical connections carefully. Then, support the tank securely as you lower it down. Remember, there are no mistakes, just happy accidents - take your time and you'll do great!

I had this same problem along with the dash lights out. I found out it was a blown fuse in the fusebox under the hood. It is a 15amp fuse. The owners manuel identifies it as "small Interior Light".

You should also check the door switch to ensure it is properly connected and functioning. The switch has a protective rubber cover and is located on the outside of the post that separates the front and back doors. Remove it for inspection by lifting the rubber flap that covers the attachment screw (below the switch plunger)and unscrewing the screw with a no. 2 Phillips screwdriver or a hex head socket. The plastic switch attaches to the holder screwed to the chassis. The switch interrupts the ground side of the electrical circuit (normally open). If the switch is not firmly seated in the holder, the metal prongs in the switch do not make contact with the chassis ground circuit. If the switch is loose, try snapping it back into place, or replace if necessary.

To change the timing belt on a 2002 Acura TL, first ensure the engine is cool, then disconnect the battery and remove the engine covers. Next, drain the coolant and remove the drive belts, crankshaft pulley, and timing belt covers to access the timing belt. Align the crankshaft and camshaft timing marks, remove the old belt, and install the new timing belt while ensuring proper tension. Finally, reassemble all components, refill coolant, and reconnect the battery.

The timing belt on a 2005 Acura TL should typically be replaced every 105,000 miles or every 7 years, whichever comes first. It's important to check the owner's manual for specific recommendations, as maintenance schedules can vary. Additionally, if you notice any signs of wear, such as fraying or cracking, it's wise to replace it sooner to prevent engine damage. Regular inspections can help ensure the timing belt remains in good condition.

It should be a 5 digit code (you have to call an acura dealer with the serial number) just press the digits and it will unlock. Hint... if you've entered the wrong code you may have to remove power to reset it.

This works for a 2003 Blazer, they may be the same.

You will actually have to remove the head light assembly to access the bulbs. The procedure will not throw off the headlight aiming a bit and it is real easy.

If you look at the top of the radiator support just above where the head lights are, you sill see two black plastic pieces that lean in toward the engine compartment on each side. They are about an inch, or so, wide. Just pull/lever them up and the head lamp will pop out for access to the bulbs.

You will need to pop out the center grill and then on each headlight unit there are two tabs (one on each side of unit) that you need to pull up. After that carefully pull out the headlight unit and remove the wires that are for the lights. To change the bulb remove the large rubber cap and twist the bulb holder to remove the bulb from headlight unit.

Begin by removing the instrument panel cover in your 1997 Acura. Remove the lightbulb, by pushing it in and turning at the same time. Install the new lightbulb in the same manner that you removed it.

The starter is located on the top of the engine, on the driver's side under the intake manifold. You remove the rear manifold mounting bracket to get to it.