0
Chrysler Sebring
The Chrysler Sebring is a range of middle-sized cars manufactured by American carmaker Chrysler between 1995 and 2010. It is one of the few practically priced automobiles available in sedan and convertible body styles.
2,284 Questions
How do you change spark plugs in a 1999 Chrysler Sebring?
First to change the spark plugs 1, 3, and 5 on the Chrysler Sebring its required to uninstall the upper intake plenum, so you could get to the rear spark plugs, benieth the plenum. Here are the steps for removing and replacing the plugs on cyl 1,3,and 5 of the V-6:
Disconnect negative cable from auxiliary jumper terminal (I believe this is the ground wire tied to the strut tower on the driver's (left) side of the car).
Unplug the connectors from the MAP sensor and (just to its front) the intake air temp sensor.
Remove the plenum support bracket bolt located rearward of the MAP sensor
Remove the bolt holding the air inlet resonator (the thing with words "multi-point injection") to the intake plenum.
Loosen throttle body air inlet hose clamp
Release snaps holding air cleaner housing cover housing
Remove air cleaner cover and inlet hoses from the engine
Unplug throttle position sensor and idle air control motor connectors.
Pry retainer tab back on throttle cable and slide cable out of bracket. Remove cable from throttle lever.
Slide Speed control cable out of bracker, if equipped. Remove cable from throttle lever.
Remove EGR tube from intake plenum.
Remove plenum support bracket bolt located rearward of EGR tube
Remove bolts holding upper intake plenum and remove plenum
Always remove the ignition cable by grasping at the spark plug boot turning the boot 1/2 turn and pulling straight back in a steady motion
Prior to removing the spark plug spray compressed air around the spark plug hole and the area around the spark plug to keep debris and dirty oil from falling into the cylinder. These loose debris can cause serious dammage.
Remove the spark plug using a quality spark plug socket with a rubber foam insert. Inspect spark plug condition. To avoid cross-threading start the plug into the cylinder head by hand
Tighten the spark plugs to 20 ft-lbs (28 N-m)
Install ignition cables over spark plugs
Install new gasket and position upper intake plenum. Tighten blots to 13 ft-lbs (18 N-m)
Install bolts at plenum support brackets (Same torque as above)
Install EGR tube at plenum. Tighten EGR tube to intake manifold plenum screws to 8 ft-lbs (11 N-m)
Install throttle and speed control (if equipped) cables
Attach electrical connectors to sensors.
Install air inlet tube clamp to to 25+/- 5 inch pounds (3 +/- 1 N-m)
Connect negative terminal to auxiliary jumper terminal.
It's required, by manufacters orders, if changing the spark plugs, in addition, need to change spark plug wires and distribuator cap and rotor. Lastly,you're going to need the proper tools for this.The tools you need are 3/8 ratchet and a set of different sizes of sockets.In addition,be careful when disconnecting the sensors around the manifold,keep everything label for rememberence.
Since your question does not indicate that the other "running" lights are not working, I suspect that they are working. Since the license plate light does NOT have it's own dedicated circuit, and therefore it's own fuse, it is not a blown fuse. IF all other rear lights, are working, then the problem is limited to the bulb SOCKET or the hot wire to it. That wire is relatively short, in that it is connected to the tail light wiring in the trunk area near one of the tail light assemblies. I can think of three possibilities that would cause the lcense plate lamp circuit to be "open:" 1. Somehow, the wire got cut or broken. 2. A connector has become disconnected. 3. Water has gotten into a connector, bulb socket, or ground connection, causing corrosion which impedes the flow of electrical current.
How do you remove the stereo amplifier under the passenger seat of a 2000 Sebring JXI conv?
You need a 90 degree socket screwdriver set, a very small one. Got mine from sears for $15.
Fuses are good still no brake lights 1996 Chrysler Sebring?
Check bulbs Check stop light switch Also make sure you have the right bulbs model 2057 bulbs.
Where is the coil wire located on a 1997 Chrysler Sebring LXI 2.5L?
The coil is inside the distributor. There is no coil wire.
The coil is inside the distributor. There is no coil wire.
How do you replace the Blower Motor Resistor Pack on a 2000 Chrysler Sebring?
its very simple, on the passanger side of the car you will find a plastic cover under the glove box, it has 2 push pins holding it up, one on the firewall and one on the passanger side by the door, remove it, look under the dash and you will see a conector with 5 or 6 wires (thats it) leavve the wires connected, you will find (2) 8mm screws holding it in place, remove them and wiggle the part out...put your new one in and slap it back together...15 min job
yes, yes you do
Be sure the ignition switch is in the "off" position. Move the steering wheel right & left while removing the key - sometimes the steering wheel lock mechanism engages and needs to be manipulated to allow ignition switch into "off" position. Airbag light is a mystery, our Sebring does this also. I have heard that one cause is a faulty airbag fuse - maybe try replacing it. For future reference, if your brake light comes on (mainly while turning) check you brake fluid level.
What would cause a 1997 Sebring Convertable engine to stall?
check the crank shaft sensor
MAP, CRANKSHAFT, CAMSHAFT SENSOR THE COMBINATION OF THOSE SENSORS WILL LET THE CAR RUN RIGHT AND NOT STALL ANY MORE
Where is the diagnostic plug in located in a 2004 Chrysler sebring lx?
It is under the dash on the driver side.
Where do you add transmission fluid in a 2002 Chrysler sebring?
The fluid is added down the dipstick tube.
Which is the fuse to clear dtc codes on a 2005 Chrysler sebring convertible?
Pulling a fuse will not clear codes on this vehicle. A scan tool is required to clear codes.
Where is the timing chain located in a 2003 Chrysler Sebring?
The timing chain is inside the passenger side of the engine.
The timing chain is inside the passenger side of the engine.
Why does your 01 sebring ac leak water into your drivers side floorboard?
A/C's don't have water in them, but your heater core could; if it is broken, this would require immediate attention as coolant fumes can harm nervous systems,liver, and kidneys in our bodies even if you can't smell them, rather quickly!
If you are seeing fluid in the mirror, or it appears to be leaking, then it wasn't a flooded car. There is a special chemical inside the mirror that causes it to get darker so you aren't blinded by headlights behind you at night. You are going to have to replace the mirror completely, or ignore it.
How much to replace water pump and timing chain on a 2002 Chrysler Sebring 2.7l dohc?
It depends on local labor rates, but tends to be more than $1000.
How do you reset the gas cap message in the dashboard on a Chrysler Sebring?
Verify that the cap is tight. Drive for a couple of days, and if the light is still on, you have a vapor leak in the fuel system and will need service.
Verify that the cap is tight. Drive for a couple of days, and if the light is still on, you have a vapor leak in the fuel system and will need service.
How can you disconnect the battery on a 2004 Chrysler Sebring convertible?
You remove the black cable from the post under the hood, on the driver side strut tower.
You remove the black cable from the post under the hood, on the driver side strut tower.
EGR Valve is dirty, or stuck open. Replace or better yet change.
How do you replace the headlight bulb in a 2002 Chrysler Sebring?
go under hood reach down where headlight is turn the light counterclock wise and pull bulb out then twist bulb and it will come out.
Can you jump a 2004 Chrysler sebring without taking the tire off?
Yes, attach the cables to the red and black jump start posts under the hood.
