0
Dodge Ram
The Dodge Ram is a large pick-up truck produced by Chrysler from 1981 to present. The car, which features a front engine and rear/four-wheel drive, was named “Truck of the Year” three times by the Motor Trend magazine.
13,744 Questions
Who is the voice for 2010 Dodge Ram?
I believe it's Sam Elliot.
If you want to double check, watch the 2007 release of "Ghost Rider" with Nicolas Cage. Sam Elliot was the character "Caretaker" and has enough lines for you to compare voices.
What is the wheel base of the 2013 RAM 3500?
The 2013 RAM 3500 has a 11 ft. 8.5 in. (140.5 in.) wheel base.
What parts are needed for A TUNE UP on a 2004 dodge ram 1500?
Spark plugs, air filter, wires ( if equipped ).
Spark plugs, air filter, wires ( if equipped ).
1978 Mercedes 300D how to bleed the cooling system?
If you mean "purge" the air out of the cooling system, then loosen the top radiator hose at the radiator. Pour coolant mixture into the hose until most of the air is purged and replace.
What is the proper spark plug gap for a 2004 dodge ram 1500 5.7L?
we are having a time with this . we have a 2004 ram with a 5,7 himi and one plug per cylender. wht is the best plug to use?
What does it mean IF THE 4X4 light keeps blinking?
It means that there is a malfunction in the 4wd system.
Does the 2001 dodge ram laramie slt have outside temperature readings?
i have a 96 dodge ram laramie slt, and it has outside temperature readings, so im sure a newer version of the same model would, yes
Main bolt torque on 6.1L Hemi?
6.1L ENGINE
DESCRIPTION N·m Ft. Lbs. In. Lbs.
Block Pipe Plugs
(1/4 NPT) 20 15 -
(3/8 NPT) 27 20 -
Camshaft Sprocket - Bolt 122 90 -
Camshaft Tensioner Plate - Bolts 28 21 -
Timing Chain Case Cover - Bolts 28 21 -
Lifting Stud 55 40 -
Connecting Rod Cap - Bolts 45
plus 60° Turn 33
plus 60° Turn -
Main Bearing Cap - Bolts
M-12 Bolts 28
plus 90° Turn 21
plus 90° Turn -
Crossbolts
M-8 Bolts 22 16 -
Cylinder Head - Bolts
M-12 Bolts
Step 1 - Tighten bolts 1-10
Step 1 - Tighten bolts 11-15 34
20 25
15 -
Step 2 - Tighten bolts 1-1 0
Step 2 - Tighten bolts 11-1 5 verify 54
20 40
15 -
Step 3 - Rotate bolts 1-10 90° - -
Step 4 - Tighten bolts 11-15 34 25 -
Cylinder Head Cover - Bolts 8 - 70
Exhaust Manifold to Cylinder Head - Bolts 31 23 -
Flexplate to Crankshaft - Bolts 95 70 -
Flywheel to Crankshaft - Bolts 75 55 -
Front Insulator - Through bolt/nut 95 70 -
Front Insulator to Block - Bolts 95 70 -
Generator - Mounting Bolt 55 40 -
Intake Manifold - Bolts12 9 106
Lifter Guide Holder 12 9 106
Piston Oil Cooler Jet - Bolts 13 10 115
Oil Pan - Bolts 12 9 105
Oil Dipstick Tube 31 23 -
Oil Pan - Drain Plug 27 20 -
Oil Pump - Attaching Bolts 28 21 -
Oil Pump Pickup Tube - Bolt and Nut 28 21 -
Rear Seal Retainer Attaching Bolts15 11 -
Rear Insulator to Bracket 68 50 -
Rear Insulator to Crossmember 41 30 -
Rear Insulator to Transmission 68 50 -
Rear Insulator Bracket - Bolts 68 50 -
Rocker Arm - Bolts 22 16 -
Thermostat Housing - Bolts 28 21 -
Throttle Body - Bolts 12 9 105
Vibration Damper - Bolt 176 129 -
Water Pump to Timing Chain Case Cover - Bolts 28 21 -
How do you change 2003 dodge ram heater control lights?
you can't replace the lights they are built in to the control head.you must replace the entire hvac control
Ballast resistor? Distributor pick up plate? I put in a new resistor and pulled one of the plugs it has spark
How do you remove the dashboard on a '95 Ram pickup?
there is screws up along the bottom of the dashboard by the floorboard and then you have to remove the screws that hold in the cup holders and ash tray if you have any other questions my e-mail is redneck_308@hotmail.com
Where is the Voltage Regulator on a 1990 Ford Taurus 3 point 0 v6?
The voltage regulator is locate in one of two places.
***The voltage regulator is located in the alternator if you have an IAR type alternator***
***The external voltage regulator (for the EVR-type alternators) is located on the driver's side wall, right next to the battery. It's much easier to see and/or remove if you remove the battery first. It has "Motorcraft" in raised lettering across the front***
I just had to remove mine.
You probably need to replace the engine thermostat. Locate the hose coming out of the top of the radiator & follow it back to the top of the engine. Where the hose attaches to the engine is where you will find the thermostat. If you have not performed a coolant flush on the engine in the last two years I would recommend to do that as well. A coolant flush should be performed every two years along with replacing the thermostat and radiator cap and aproximately three gallons of antifreeze ( dillute antifreeze to manufactuers specs.). All total I would estimate it will cost you 50 dollars if you do it yourself.
Why would gas leak from a hose at the rear driver's side of a 1999 Nissan Altima?
Because there is a hole in the hose! Replace the hose
