0
Ford Bronco
Manufactured from 1966-1996, the Ford Bronco is a two-door sport utility vehicle produced in five generations. Broncos are divided into two categories, which are the early Broncos and the full-size Broncos, and were later replaced by the larger Ford Expedition.
1,597 Questions
Changing the Radiator in a 1990 Ford Bronco II?
# Disconnect negative battery cable # Drain cooling system # Loosen the hose clamps then detach the radiator hoses from the fittings # Disconnect the reservoir hose from the radiator filler neck # If the radiator is equipped with a finger guard remove it.If it has a shroud remove the screws that attach the shroud to the radiator and slide the shroud toward the engine # If the truck is a automatic disconnect the cooler lines from the radiator # Plug the lines and fittings to avoid spillage # Remove the radiator mounting bolts and brackets # Lift the radiator up and out of its lower mounting pads or grommets
Where is the speedometer cable located on a 1989 celebrity?
There isn't one. The 88 and up GM cars went to a VSS, or Vehicle Speed Sensor. It is located on the top of the transmission, usually right under the brake booster area.
How many fuel injectors are in a 1989 ford bronco full size?
There Should be 8. Four under the intake manifold and four along where the temp sensor is.
proably a bad sensor
How do you repair the tailgate of a 1989 Ford Bronco if it is stuck shut?
If the tailgate is stuck in the closed position it will be one of three things. Well, four things if you include someone welding it shut but I hope you would notice the weld burns... lol. Now then. A- the hinge and releases are rusted solid. It's not likely but it is possible. B- Body damage can tweak the whole rear of the Bronco and jam the tailgate shut. C- (and the most likely) The rods inside the tailgate that release it from the latch pins are no longer connected to the handle. If neither A or B are the cause, get inside and remove the inside panel of the tailgate. Connected to the handle there will be a couple metal rods going left and right. They're held in place with little plastic clips that commonly rot, crack and fall apart. The little plastic clips are available for a few bucks at any auto parts store. Replace them, lube up the moving bits and test it out. it that fixes it, put it all back together and you're welcome. If not, well...
Is it possible to put a Ford 2.0 Ztec engine in a Ford Pinto?
Possible? Yes it is possible. Easy? NO! This would be a very difficult swap. You better have lots of skill and the proper tools.
Can I prevent my motorbike from rusting by spraying diesel all over it after a full service wash?
spraying diesel on it will not keep it from rusting it will damage the bike
How much does a EFI to carb conversion cost on a 94 bronco with a 302 v8?
check on www.summitracing.com for the components you need.
Why did Henry Ford start the Ford motor company?
Henry Ford was an innovative businessman who, like many company owners, saw a need and wanted to fill that need. The Ford motor company grew out of Ford's own inventiveness. In 1896, Ford invented the Quadricycle, the first "horseless carriage" that he produced. Its popularity helped fund and launch Ford's business, and the new Ford Motor Company was founded 7 years later, on 16 June 1903.
Why is my 89 ford bronco hard to start and have small puffs of white smoke?
The white smoke could be caused by coolant leaking into the combustion chamber, though a cracked head or bad gasket.
Spray lots of wd-40 in the driver side latch, there is a mechanism in there that allows power to flow to the motor when the tailgate is closed. more than likely it is just dirty and stuck. Thing is you have to get the tailgate open.
Right answer:
BY r3dn3ck:
The answer above is almost entirely incorrect. It might be heavier heheheh. Well, yeah it is. Specifically, depending on the year of motor you use it'll be ~26lbs or ~44lbs heavier. It will fit well as has been demonstrated many times by the dozen or so Lightning swapped P71's. The only difference between a 4.6 and a 5.4 is deck height and the things that affects so it swaps fairly easily. The motor mounts are identically placed between the two relative to the oil pan rail. All the accessories transplant easily.
You'll want to buy a motor from a <01 expedition or van for the easiest time. You will need an intake manifold or intake adapter plates for good car performance (the truck intake is best left to trucks). A dyno tune is recommended but not mandatory. Cars with automatic transmissions should consider it mandatory for best drivability to get a dyno tune with a chip or handheld (costs about 500 bucks for the tune and chip/handheld) as the torque settings in the tune affect shifting of the trans.
Then check out www.hiperformancesolutions.com/54.HTML. HPS makes an intake manifold dedicated to swapping 5.4L 2v engines into places that used to have 4.6L 2v engines (mustangs, Crown Vics, etc...) without having hood clearance problems.
Don't take my word or ^^ his. Google it and look for cars on streetfire.net that have been swapped.
Will a c6 transmission bolt up to a 351 modified?
Depends.if the bell ( where it covers the flywheel behind the motor) is a bog block.or small block bell housing. Like a small bell housing will bolt to a 302 and big bell.housing will bolt to.a 460
What year did ford quit making broncos?
Ford stopped productions of the Bronco in 1996, but the have a prototype for a possible 2009 model pictures can be seen here http://loadinform.com/2009-ford-bronco/
What would cause Oil pressure problems on 1986 ford bronco?
There are a variety of reasons from a bad sender or gauge to low oil level to worn bearings. Check the sender first as it's the easiest.
Would an F-150 with a cap on the back get the same mpg as a bronco in the same year?
No, the bronco weighs more ...and it also depends on engine size, driving habits etc .....
Exhaust smell in cabin of van?
Could use more info like year, make and model van but in any case have a garage check it out asap before someone dies from carbon monoxide poisoning.
How do you remove the rotor from a 1996 ford bronco 4x4?
If you mean the rotor from inside the distributor. Just unclip the 2 clips and lift up the distributor cap then use a nut driver to remove the 2 bolts on the rotor.
How do you change leaf springs on full size 1989 ford bronco?
To change the leaf springs on a 1989 Ford Bronco, first, safely lift the vehicle and secure it on jack stands. Remove the rear wheels, then unbolt the U-bolts and any associated hardware connecting the leaf springs to the axle and frame. Once the old leaf springs are removed, install the new springs by reversing the removal process, ensuring all bolts are tightened to the manufacturer's specifications. Finally, reinstall the wheels and lower the vehicle to the ground.
How do you slim Jim 1987 ford bronco II?
Slim Jimming a 1987 Ford Bronco II involves using a slim jim tool to unlock the door without a key. First, carefully insert the slim jim between the window and the weather stripping, aiming for the lock mechanism inside the door. Gently manipulate the tool to catch the lock rod and pull it up to unlock the door. Be cautious to avoid damaging the wiring or window components during the process.
