Geo Tracker

tighten brake switch located on top of brake pedal under dash adjust so lamps are out and come on with light pressure on pedal.

I have a 95 Tracker as well and recently it turned 100,000 miles. At 100,001 the "check engine light" came on. A local mechanic did a diagnostic and it also didn't give any codes to help reset the light or alert me of a problem. I asked him about the reset "switch" under the dash and he said he never heard of that. I investigated on my own when I got home, because the light being on was driving me crazy, and there actually is a small switch that reset the light. I removed the small plastic panel under the steering column and found it between the drivers side speaker and the steering column. It is really small. It is a black plastic switch with a metal face plate. You really have to look for it because it's settled in with the wire harness' under the dash. I flipped the switch and the light went out. Again be patient when looking for the switch. It's there you just have to look close to the dash and next to the steering column. I tried removing the battery cables because I read that that would reset the light but had no luck doing it no matter how long I left them off.

195/75R15

Step on brake first.

Turn steering wheel slightly to remove tension on key.

they have pictures and everything in books called chiltin manuals at pep boys. the 96 starts suzuki

It could be a sensor or anything it happens to a lot of cars. You can have a diagnostic done on it or first you nac remove the battery cables to reset everyhting. If it comes on again I would have a diagnostic reading done at your local mechanics shop. You can also buy the peice and do it yourself if you have the manual.

Runs bad how? Black smoke....rough running?...check the water temperature sensor (if hard starting when cold outside and instead of idling high as usual, goes right to low idle), and O2 sensor (if black smoke). Possible you have a loose injector (Throttle body) or failing fuel pressure regulator (if flooding out). Many things are possible. Weird idle? Check for vacuum tube leaks. If rough idle, can sometimes be the EGR valve. Get a Haynes manual, and debug.

I believe that 1996 and newer are OBDII, any auto partsrepair shop or dealer can tell you, I have a 97 and it's OBDII, Mike All cars and light trucks built and sold in the United States after January 1, 1996 were required to be OBD II equipped. In general, this means all 1996 model year cars and light trucks are compliant, even if built in late 1995. Two factors will show if your vehicle is definitely OBD II equipped: 1) There will be an OBD II connector that has 16 pins. The connector must be located within three feet of the driver and must not require any tools to be revealed. Look under the dash and behind ashtrays. 2) There will be a note on a sticker or nameplate under the hood: "OBD II compliant".

my 1990 has 4" speakers hole in the back but i have 5" speakers in there now.

You'll need about one and a half to two quarts of standard 80 or 90 weight. I'd recommend GM Syncromesh, but any type will do. I might also add that it's the same weather front or back diff. or auto or manual trans. Josh 95 Geo Tracker TBI 2x4 5-speed w/ soft top

Yes! No, not the right fit.

The fuse box diagram is in the owners manual of this car. It is also found on the back of the fuse box panel cover.

in the glove box

It is held in place by plastic slips. Move the seat either all the way back or all the way forward to gain access.

it could be belt pulley rubbing on the timing belt cover or it could be the berries in the wheel but if its making grinding noise while ilding then def check your pulley make sure it isn't rubbing on anything or it could be the flywheel theres numbers of things to check over for the grinding noise

On a 1999 GEO Tracker, a bad fuse can cause the headlights and dash lights to blink. A bad voltage regulator or alternator can also cause lights to blink and flicker.

on my 93 geo tracker lsi 5 speed manual with a 1.6 liter 4 cyl i get about 45 miles to the gallon on the highway and about 35 in town

see my CEL page (DTC')

see my profile see link.

it should be 1-3-4-2 also

Hi, I've found the easiest way to replace the bulb is first remove the center console, just 4 screws. I took this time to clean and wash it, rather my wife did. The remove the two screws near the dash side of the shift console, now there are two screws at the rear of the shift console that just need to be loosened because that end of the shift console has two slotted plastic tabs the screws go over, these are easy to break ( I have broken one) the screws are a pain to loosen too. then just raise the shift console and remove the light bulb from it's socket ( a half or quarter turn ) and remove the bulb from its socket. Now just reverse all the steps. If you have the time or patience left, you can vacumn everywhere ( I did ). One problem I had was that the wires that are at the socket were broken so I went to a local auto-recycler ( junk yard ) and went and found a bulb socket assy and removed it, paid for it ($5.00 ) and instaled it. I hope this helps and good luck. Steve H.

ITEM IS LOCATED ABOVE LICENSE PLATE AS STATED........MY HANDLE WAS SO RUSTED IT WOULDNT MOVE..........SO IF YOU ARE THE SAME.....GET IN THE BACK OF THE VEHICLE...REMOVE THE PLASTIC PIECES ON THE INSIDE OF THE TAILGATE.........PUSH THE MIDDLE OF THE BUTTON THINGS HOLDING ON THE PLASTIC.....WITH A SMALL FLATHEAD SCREWDRIVER REMOVE THE BUTTON THINGS........THEN WHEN ALL BUTTONS REMOVED .....TAKE OF PLASTIC PIECE......................INITIALLY YOU WILL SEE FOUR 10 MM NUTS.... REMOVE THE OUTER TWO.......THIS WILL THEN REMOVE THE COVER TO THE HANDLE........

YOU WILL THEN PROB NOTICE THAT THE HANDLE IS RUSTED LIKE NO OTHER.....YOU CAN ATTEMPT TO LUB HANDLE UP AND MIGHT MOVE........BUT I WAS NOT SO LUCKY..GOOD LUCK

i want to know how to rebuild a manual transmission for a 1990 Geo Tracker 4x4

The answer is YES. The question is how money will it cost to replace/repair the failed parts that cused the lock up. It could be a broken connecting rod, spun bearing, failed oil pump, or seized piston. You can buy parts and send the bare engine block to a machine shop so they can recondition it. If you are not mechanically inclined and depending what the issue is, it willgenerally cost about as much to repair the engine as it costs to replace the engine (unless you buy a used engine and can istall it your self).

to tow a 1992 Geo Tracker you must either disconnect the drive shaft or use a tow dolly and tow it backwards or you will damage the transmission

in the glove compartment, You cant see it unless you bend down and look up towards the top of the glove compartment on the right side. It's a pull handle.